Next ASHTON 868279 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• For general cleaning, periodically dust with a soft cloth.
• Not suitable for use in bathrooms.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Do not rub or scrub the surface when cleaning.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Made from MDF with painted finish.
• Made in China.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
868279 ASHTON CONSOLE
Page 1 of 6

1. Insert 3 x cambolts (A) and 2 x wooden dowels
(D) into 1 x lower rail 7.
2. Attach lower rail 7 to bottom panel 6.
3. Insert 3 x camlocks (B) into bottom panel 6.
Ensure the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1. Insert 3 x cambolts (A) and 2 x wooden dowels
(D) into 1 x lower rail 7.
2. Attach lower rail 7 to bottom panel 6.
3. Insert 3 x camlocks (B) into bottom panel 6.
Ensure the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
PARTS
STEP TWO
STEP ONE
FITTINGS
B
B
B
A
D
A
A
D
B
B
B
A
A
A
D
D
(1) Top Panel x 1
(7) Lower Rail x 2
(2) Side Panel (L&R) x 2
(5) Shelf Rail x 1
(3) Back Panel x 1
(6) Bottom Panel x 1
(4) Divider Panel x 1
Page 2 of 6

1. Attach back panel 3 to divider panel 4 with 2 x
screws (F) and tighten.
2. Insert 1 x wooden dowel (D) to divider panel 4.
3. Attach shelf rail 5 to the assembled unit with 1 x
screw (F) and tighten.
1. Insert 7 x cambolts (A) and 3 x wooden dowels
(D) into side panel 2-L.
2. Attach bottom panel 6,back panel 3 and shelf
rail 5 to side panel 2-L.
3. Insert 7 x cambolts (B) into bottom panel 6,back
panel 3 and shelf rail 5. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 7 x cambolts (A) and 3 x wooden dowels
(D) into side panel 2-R.
2. Attach side panel 2-R to the assembled unit.
3. Insert 7 x cambolts (B) into bottom panel 6,back
panel 3 and shelf rail 5. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
STEP THREE
STEP FOUR
STEP FIVE
A
D
D
A
A
DAA
BB
B
B
B
A
A
B
B
D
AA
A
D
A
A
B
B
B
B
B
AA
B
B
D
F
F
F
Page 3 of 6

1. Insert 8 x cambolts (A) and 4 x wooden dowels
(D) into top panel 1.
2. Attach top panel 1 to the assembled unit.
3. Insert 8 x camlocks (B) into side panel 2 (both
L&R) and divider panel 4. Ensure the arrow
indicator is pointing towards the panel edge
before tightening with a screwdriver.
1. Insert 4 x cambolts (A) into drawer front panel 8-
L.
2. Attach drawer side panel 9 (both L&R) to drawer
front panel 8-L.
3. Insert 4 x camlocks (C) to drawer side panel 9
(both L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
4. Insert drawer bottom panel 11 into the grooves
of the drawer side panel 9 (both L&R).
5. Attach drawer back panel 10 to the assembled
unit with 4 x screws (E) and tighten.
6. Attach 1 x handle (H) to drawer front panel 8-L
with 2 x bolts (G) and tighten.
1. Insert 4 x cambolts (A) into drawer front panel 8-
R.
2. Attach drawer side panel 9 (both L&R) to drawer
front panel 8-R.
3. Insert 4 x camlocks (C) to drawer side panel 9
(both L&R). Ensure the arrow indicator is pointing
towards the panel edge before tightening with a
screwdriver.
STEP SEVEN
STEP SIX
STEP EIGHT
C
A
C
A
AA
DD
DD
A
A
AAA
B
B
B
B
B
A
AB
B
B
C
A
C
A
AA
D
AA
A
D
A
A
B
B
B
B
B
AA
B
B
Page 4 of 6

4. Insert drawer bottom panel 11 into the grooves
of the drawer side panel 9 (both L&R).
5. Attach drawer back panel 10 to the assembled
unit with 4 x screws (E) and tighten.
6. Attach 1 x handle (H) to drawer front panel 8-R
with 2 x bolts (G) and tighten.
1. Insert the drawer into the unit.
2. Insert 2 x paper cards (J) to 2 x handles (H).
1.Use screw (C) and washer (B) to secure the
nylon strap (A) to the top panel.
2.Secure the other end of the strap to the wall with
an appropriate screw and wall plug for your wall
type. To hide the strap behind the unit, drill the
holes lower than the top of unit.
Warning :Always ensure the area to be drilled is
free from hidden electrical wires, water and gas
pipes.
NB: Wall fixings are not included-please source
suitable fixings for your wall type. If in doubt
please consult a qualified trades person.
STEP NINE
STEP TEN
SCREW
TOP
B
C
A
C
A
AA
Page 5 of 6

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6