Next CORSICA 760284 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless
the item is found to be faulty. Should you need to return the unassembled product, please repack in the
original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
760284 CORSICA MEDIA CABINET
760284 CORSICA MEDIA CABINET 760284 CORSICA MEDIA CABINET
760284 CORSICA MEDIA CABINET
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-
step
• A minimum of two persons is required to assemble this product.
• Made from honeycomb board , partical board & MDF with a wood effect finish.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Made in China.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking,
discolouration or warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to
prevent scratching or damage.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• All assembly fixings should always be tightened properly and periodically check all fixings and
tighten if necessary.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
tighten if necessary.
Page 1 of 8

PARTS
FITTINGS
1.Attach panels 17 & 18 to panel 19 with
4×screws(F) by using a screwdriver until tight.
STEP ONE
Page 2 of 8

1.Slide panel 15 into the grooves of the
drawer frame
1.Insert 2×cambolts(A) into panel 16 using a
screwdriver until tight.
2.Glue and insert 2× wooden dowels(C) into
panels 18 & 17
3.Attach panel 16 to panels 18 & 17.
4.Insert 2×camlocks (B) into panels 18 & 17 and
tighten with a screwdriver.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
STEP THREE
STEP TWO
the panel edge before tightening with a
screwdriver.
5.Attach handle (H) to the panel 16 with screws
provided.
6.Repeat step one,two & three to assemble
the other three drawers.
1.Insert 15xcambolts (A) into panels 1,2,4,6 & 8 by
a screwdriver until tight.
STEP FOUR
Page 3 of 8

1.Glue and insert 2x wooden dowels(D) into panels
7
2.Attach panel 8 to panel 7.
3.Insert 3x camlocks (B) into panel 7 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing
towards the panel edge before tightening
with a screwdriver.
1.Attach panel 2 to panel 7 with 2 x screws(G) by
an Allen key (J) to tighten.
STEP FIVE
STEP SIX
1.Glue and insert the wooden dowel (D) into panel
2
2.Attach panel 14 to panel 2.
3.Insert 2x camlocks (B) into panel 14 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing
towards the panel edge before tightening
with a screwdriver.
STEP SEVEN
Page 4 of 8

1.Glue and insert 2x wooden dowel (D) into panel
1.
2.Attach panel 1 to panel 7.
3.Insert 2x camlocks (B) into panel 7 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing
towards the panel edge before tightening
with a screwdriver.
1.Turn over the frame
2.Glue and insert 4x wooden dowels (D) into
panels 1 & 2 .
3.Attach panels 4 & 6 to panels 1 & 2.
4.Insert 8x camlocks (B) into panels 1&2 and
tighten with a screwdriver.
Ensuring the arrow indicator is pointing
towards the panel edge before tightening
STEP EIGHT
STEP NINE
towards the panel edge before tightening
with a screwdriver.
STEP TEN
1.Slide panels 10(x2) into the assembled unit as
shown in diagram.
Groove
Page 5 of 8

STEP ELEVEN
1.Glue and insert the 3xwooden dowels (C) into
pnael 13
2.Attach panel 13 to panel 4.
1.Slide panels 11 & 12 into the assembled unit as
shown in diagram.
STEP TWELVE
Finished side
1.Slide panels 3 & 5 into the assembled unit as
shown in diagram.
STEP THIRTEEN
Page 6 of 8

1.Attach panels 3 & 5 to panels 1 & 2 with 8 x
screws(G) by an Allen key (J) to tighten.
STEP FIFTEEN
1.Carefully lift the unit upright
2.Insert 8 x fittings (I) into the required position of
panels 7,5 & 6.
3.Insert panels 9(x2) onto the fittings (I) .
STEP FOURTEEN
1
STEP SIXTEEN
1. Insert the drawers 16(x4) to the assembled unit
as shown in diagram.
Finished side
Page 7 of 8

STEP SEVENTEEN
1.Insert 8×plastic fasteners (K) into the back panel
grooves and tighten with screws provided.
STEP EIGHTEEN
1.Using screw and washer secure the 2 x nylon
straps (L) to the back of top panel.
2.Secure the other end of the strap to the wall with
an appropriate screw and wall plug for your wall
type (not provided).To hide the strap behind the
unit ,drill the hole lower than the top of unit.
unit ,drill the hole lower than the top of unit.
Warning:
Always ensure intended wall area to be
drilled is free from hidden electrical wires,
water and gas pipes.
NB:Wall fixings are not included-Please source
suitable fixing for your wall type. If in doubt
please consult a qualified trades person.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
Page 8 of 8