Next CORSICA User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0333 777 8999
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should
you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
CORSICA EXTENDING DINING TABLE
CORSICA EXTENDING DINING TABLECORSICA EXTENDING DINING TABLE
CORSICA EXTENDING DINING TABLE
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
CARE INSTRUCTIONS
• Do not use furniture polish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage.
• Do not put hot dishes directly on the surfaces of the item.
• Made in China.
• Keep fittings out of children's reach and keep children well away from the construction area.
PRODUCT INFORMATION
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of two persons is required to assemble this product.
• Made from honeycomb board , partical board & MDF with a wood effect finish.
Page 1 of 6

FITTINGS
PARTS
1.Attach 4 × latches (C) to panels 4 & 11 with 8 × screws
(D) using a screwdriver until tight.
3.Attach 4 × latch hooks (C) to panels 3 & 11 with 8
×screws (D) using a screwdriver until tight.
STEP ONE
Page 2 of 6

1.Insert 4 x nuts (M) into panels 1 (x2) & 2 (x2) .
2.Insert 12 × bolts (J) into nuts fixed on panels 1 (x2) &
2 (x2) and turn bolts (J) clockwise until tight by hands.
1.Attach panels 5 (x2) to panels 3 & 4 with 6 x screws (F)
and tighten with an Allen key (G) .
STEP TWO
STEP THREE
1.Glue and insert 12 x wooden dowels (A) into ends
of panels 1 (x 2) & 2 (x2).
2. Attach panels 1 (x2) & 2 (x2) to panels 5 (x2), 3 & 4 .
3. Slot 8 X metal pieces (K) onto bolts ( J ) ,and thread
8 X springs (L) onto bolts (J) ,then screw 8 X metal
nuts (I) with spanner (H) until tight .
Please note :We recommend that the
packaging is used to protect the
surfaces during assembly.
STEP FOUR
Page 3 of 6

1.Glue and insert 8 x wooden dowels (A) into ends
of panels 6,7,8 & 9.
2. Attach panels 6,7,8 & 9 to panels 1 (X2) & 2 (x2).
3. Slot 4 X metal pieces (K) onto bolts ( J ) ,and thread
4 X springs (L) onto bolts (J) ,then screw 4 X metal
nuts (I) with spanner (H) until tight .
4.Tighten the panels 6,7,8 & 9 to panels 3 & 4 with
12 x screws (F) and tighten with an Allen key (G) .
1.Ensure latches (C) on panel 4 are open as shown in diagram.
2.Attach panels 3, 6 & 7 to panels 4, 8 & 9.
3.Ensure all panel edges and assembly pins
lined up and close the table top together.
close all latches to secure in place.
STEP SIX
STEP FIVE
1.Attach panels 12 & 13 to panels 3 & 4 with 16 x screws (F)
and tighten with an Allen key (G) .
STEP SEVEN
Page 4 of 6

1.Attach panels 10(x2) to panels 12 & 13 with 8 x screws (E)
and tighten with an Allen key (G) .
please noted: the velvet side face to panels 3 & 4
1. Carefully lturn over the unit , the unit should be lifted by two
people as shown
STEP NINE
STEP EIGHT
1.Open latches (C) on panels 3 ＆
＆＆
＆ 4 as shown in diagram .
STEP TEN
Page 5 of 6

1.Extend the apron on panel 11 as shown.
2.Extend the table top as shown.
3.Insert panel 11 into the open area.
4.Ensure all panel edges and assembly pins
lined up and close the table top together.
close all latches to secure in place.
STEP ELEVEN
(Removing the central extension piece)
1.Extend the table tops as shown.
2.Store the panel 11 above the panels 10 (x2).
3.Ensure panel edges and assembly pins
lined up and close the table top together.
close all latches to secure in place.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP TWELVE
Page 6 of 6