Next HARTFORD 844249 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
FITTINGS
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Do not rub or scrub the surface when cleaning.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not put hot dishes directly on the surfaces of the item.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made in China.
• A minimum of 2 persons is required to assemble this product.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• For general cleaning, periodically dust with a soft cloth.
PRODUCT INFORMATION
• Made from Pine with NC lacquer finish.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
CARE INSTRUCTIONS
• Natural features ensure that each piece is individual. Every effort is made to ensure colour continuity between
pieces, however this is a natural product, slight colour variations and natural grain markings may occur.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
844249 HARTFORD BENCH
Page 1 of 5

1. Attach 3 x hinges (C) to top panel 1, using 9 x
screws (D). Tighten with a screwdriver.
2. Insert 4 x dowels (E) to bottom panel 2.
STEP ONE
PARTS
4. Insert 2 x cambolts (A) and 4 x dowels (E) into
panel 5.
3. Insert 2 x cambolts (A) and 4 x dowels (E) into
panel 6.
Page 2 of 5

1. Insert 8 x cambolts (A) into 2 x rails 3.
2. Insert 8 x cambolts (A) into 2 x rails 4.
1. Insert 6 x dowels (E) to panel 8.
2. Insert 4 x cambolts (A) and 8 x dowels (E) into 2 x
panel 6.
1. Attach rails 3 & 4 to panel 7.
1. Attach panels 5 & 6 to panel 8.
STEP FIVE
STEP FOUR
2. Insert 4 x camlocks (B) into panel 8. Tighten with a
screwdriver.
2. Insert 4 x camlocks (B) into panel 7. Ensure the
arrow indicators on the camlocks are pointing
towards the panel edges and ensure the assembly
bolts locate properly into the camlocks before
turning clockwise with a screwdriver to tighten.
3. Repeat above steps to assemble another rails 3 &
4 to another panel 7.
STEP THREE
STEP TWO
Page 3 of 5

1. Attach bottom panel 2 to the assembled unit, using
2 x screws (F). Tighten with a screwdriver.
1. Attach side panels to the assembled unit.
STEP SIX
STEP SEVEN
2. Insert 8 x camlocks into panels 5 & 6. Tighten with
a screwdriver.
STEP EIGHT
1. Insert 4 x camlocks into bottom panel 2. Tighten
with a screwdriver.
Page 4 of 5

1. Attach 2 x support hinges to top panel 1 and panel
6, using 8 x screws (G). Tighten with a screwdriver.
Next Retail Ltd, Desford Road, Enderby, Leicester, LE19 4AT
STEP NINE
STEP TEN
1. Attach top panel 1 to the assembled unit, using 9 x
screws (D) to fix 3 hingers (C) to top panel 1. Tighten
with a screwdriver.
Page 5 of 5