Next 896225 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
• Made from MDF with a painted finish.
• Do not rub or scrub the surface when cleaning.
• Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• For general cleaning, periodically dust with a soft cloth.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Not suitable for use in bathrooms.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Made in China.
PRODUCT INFORMATION
• Do not put hot dishes directly on the surfaces of the item.
CARE INSTRUCTIONS
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
896225 ASHTON DESK
Page 1 of 8

1. Insert 2 x wooden dowels (D) into top panel 1.
2. Attach top front rail 7 to top panel 1 with 3 x
screws (E), tighten with a screwdriver.
1. Attach 1 x wooden stopper (F) to shelf panel 6
with 2 x screws (G), tighten with a screwdriver.
1. Insert 2 x cambolts (A) and 2 x wooden
dowels (D) into side panel 2 and divider panel 5.
2. Attach side panel 2 and divider panel 5 to
supporting rail 6 .
3. Insert 2 x camlocks (B) into supporting rail 6.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
PARTS
STEP ONE
STEP TWO
STEP THREE
FITTINGS
1
62
5
Page 2 of 8

1. Insert 4 x wooden dowels (D) into side panels
2 and divider panel 5.
2. Attach bottom panel 4 to the assembled unit
with 4 x screws (E) and tighten with a
screwdriver.
1. Insert 3 x cambolts (A) and 1 x wooden dowel
(D) into divider panel 5.
2. Attach back rail 8 and back lower supporting
rail 18 to divider panel 5.
3. Insert 3 x camlocks (B) into back lower
supporting rail 18 and back rail 8. Ensure the
arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
1. Insert 3 x cambolts (A) and 1 x wooden dowel
(D) into side panel 3.
2. Attach side panel 3 to the assembled unit.
3. Insert 3 x camlocks (B) into back lower
supporting rail 18 and back rail 8. Ensure the
arrow indicator is pointing towards the panel
edge before tightening with a screwdriver.
STEP FIVE
STEP FOUR
STEP SIX
2
5
4
8
18
2
5
8
18
3
2
5
Page 3 of 8

1. Insert 6 x wooden dowel (D) into side panel
2,divider panel 5 and side panel 3 .
2. Insert 8 x cambolts (A) into top panel 1 .
3. Attach top panel 1 to the assembled unit.
4. Insert 8 x camlocks (B) into side panel
2,divider panel 5,side panel 3 and back rail 8.
Ensure the arrow indicator is pointing towards
the panel edge before tightening with a
screwdriver.
1. Attach back panel 11 to the assembeld unit
with 14 x screws (H) and tighten.
1. Insert 3 x cambolts (A) and 2 x wooden dowel
(D) into front rail of keyboard tray 12.
2. Attach front rail of keyboard tray 12 to bottom
panel of keyboard tray 13 .
3. Insert 3 x camlocks (C) into bottom panel of
keyboard tray 13. Ensure the arrow indicator is
pointing towards the panel edge before
tightening with a screwdriver.
STEP NINE
STEP EIGHT
STEP SEVEN
2
83
5
Page 4 of 8

1. Insert 4 x cambolts (A) into the drawer front
panel 14.
2. Attach drawer side panels 16 (both L&R) to
drawer front panel 14.
3. Insert 4 x camlocks (C) into drawer side panels
16 (both L&R). Ensure the arrow indicator is
pointing towards the panel edge before
tightening with a screwdriver.
4. Insert the drawer bottom panel 17 into grooves
of drawer side panels 16 (both L&R).
5. Attach drawer back panel 15 to the assembled
unit with 4 x screws (G) and tighten.
6. Attach 2 x handles (M) to drawer front panel 14
with 4 x bolts (N) and tighten.
1. Insert the drawer and keyboard tray into the
unit.
1. Attach 2 x hinges (L) to door panel 10 with 4 x
screws (K) and tighten with a screwdriver.
STEP TEN
STEP ELEVEN
STEP TWELVE
Page 5 of 8

1. Attach 4 x handles (M) to door panel 10 with 8
x bolts (N) and tighten.
1. Attach door panel 10 to the assembled unit
with 4 x screws (K) and tighten.
Note: The gaps between the door and frame can
be changed by making adjustments to the hinges
with a screwdriver. Refer to adjustment
diagrams.
Laterally (Side to Side)
Front to back
Vertically ( up and down)
1. Insert 4 x shelf supporters (J) to side panel 2
and divider panel 5. Ensure all supports are at
the same level for each shelf.
2. Place the adjustable shelf panel 9 onto the
shelf supports (J).
STEP FOURTEEN
STEP FIFTEEN
STEP THIRTEEN
Page 6 of 8

1. Insert 6 x paper cards (P) to 6 x handles (M).
1. Use screw (S) and washer (R) to secure the
nylon strap (Q) to the top panel.
2. Secure the other end of the strap to the wall
with an appropriate screw and wall plug for your
wall type. To hide the strap behind the unit, drill
the holes lower than the top of unit.
Warning : Always ensure the area to be
drilled is free from hidden electrical wires, water
and gas pipes.
NB :Wall fixings are not included-please
source suitable fixings for your wall type. If in
doubt please consult a qualified trades person.
STEP SIXTEEN
STEP SEVENTEEN
P
P
P
P
P
P
Page 7 of 8

PACKAGING LAYOUT
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 8 of 8