Next LEAMINGTON DOUBLE BED User manual

Tools Needed
Helpline
If you have any problems with this product or
require
any replacement fittings please contact Customer
Services Tel: [phone]
• For general cleaning, periodically dust with a soft cloth.
• Do not put hot dishes directly on the surfaces of the item.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Do not use abrasive cleaning products or those containing silicone.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not rub or scrub the surface when cleaning.
• Made in China.
CARE INSTRUCTIONS
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging
IMPORTANT
• A minimum of persons persons is required to assemble this product.
PRODUCT INFORMATION
• Made from steel with a nickle plated finish and poplar sprung wooden slats.
LEAMINGTON BED (DOUBLE)
Page 1 of 5

FITTINGS
PARTS
A.Bolts x 12
M6X20mm
H.Spanner x
1
C.Bolts x 4
M6X55mm
E.Plastic Washer x
8
D.Nut x 2
M6
G.Allen key x
1
F.Metal Washer x
(1)Headboard x 1
(2)Footboard x 1
(3)Side Rail x 2
(5)Center Rail x 1
(4)Cross Bar x 2
(6)Sprung Slats x 30
(7)Plastic cap
(one end open) x
(11)Finials x
(10)Fabric x 2
(13)Supporting x 2
(8)Plastic cap
B.Bolts x 4
M6X40mm
(12)Foam Pads x 4
(9) Foot Slider
x 4
Page 2 of 5

1. Attach side rails 3 (x2) to headboard 1 and
footboard 2 using 8 x bolts (A), 8 x plastic washers
(E)
and 8 x metal washers (F). Tighten using Allen key
(G)
NOTE: Ensure the threaded insert holes in cross bars 4
(x2) are facing downwards
STEP TWO
STEP ONE
1.Attach Foot Slider (9) to Headboard 1 and
Footboard 2
by using Bolts (B), Metal Washer (F)and tightening
with
Allen key (G).Peel the rear tape from the Foam Pads
(12)
and stick them to the base of the Foot Slider (9).
STEP THREE
1. Attach cross bars 4 (x2) to the brackets on side rails 3
(x2) using 4 x bolts (A) and 4 x metal washers (F). Tighten
with Allen key (G).
Page 3 of 5

1. Attach centre rail 5 between the brackets on cross
bars 4 (x2) using 2 x bolts (C), 4 x metal washers (F)
and 2 x nuts (D). Tighten with Allen key (G) and
NOTE: Please ensure that the slat cap holes on the
centre rail 5 face upwards.
1. Attach 2x support leg 13 to centre rail 5 using 2 x
bolt (C), 2x metal washer (F) and tighten with Allen
key (G).
IMPORTANT
Once the feet have been assembled and attached,
they should be adjusted to ensure they do not touch
the floor, (5mm above the floor) to allow for
movement once the mattress is placed on the bed
It is important to note that when moving the bed that
it is not dragged into its new position to prevent the
possibility of these feet being twisted or angled to
one side, which could lead to the collapse of the
centre of the bed.
To move the bed, remove the mattress and lift the
bed into its new position to avoid damage. Ensure
the feet are at 90° to the floor before replacing the
STEP FOUR
STEP FIVE
Page 4 of 5

1. Insert a sprung wooden slat 6 through the first
hole in strap 10. Repeat using another sprung
wooden slat 6 and the other strap 10.
2. Attach single sided slat cap 7 onto one end of the
sprung wooden slat 6. Attach another single sided
slat cap 7 onto the other end of the second sprung
wooden slat 6.
3. Attach both sprung wooden slats to the
assembled bed base by inserting each single sided
slat cap 7 into side rails 3 (x2) and using double
sided slat cap 8 in the centre. Once each slat has
been inserted into the slat caps, ensure the double
sided slat cap is firmly pushed into the holes in
4. Repeat process for all remaining slats and caps
until all components have been used and firmly
pushed in place.
1. Attach finials 11 X 4 to headboard 1 and footboard
2 turning clockwise by hand to tighten.
STEP SIX
STEP SEVEN
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 5 of 5