Next PARIS 899684 User manual

Tools Needed
Helpline
If you have any problems with this product or require
any replacement fittings please contact Customer
Services Tel: [phone]
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry naturally.
• For more stubborn stains a professional upholstery cleaner should be consulted.
• Clean periodically in situ using a professional cleaning company.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may affect the finish. Avoid prolonged contact with such products.
• Please do not apply adhesive substrates to the product, e.g. sticky tape.
• Keep fittings out of children’s reach and keep children well away from construction area.
• Foam is supplied to protect the front face. Do use the foam to protect the main face during assembly.
• Made in China.
• Made with 100% polyester, nelson mink fabric covering.
• Regular cleaning is essential to avoid build up of these products on the surface.
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and soak up any
liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet cloth.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources such as
radiators.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
PRODUCT INFORMATION
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
• Carefully check that you have all the parts before beginning assembly.
• We recommend that the packaging is used to protect the surfaces during assembly.
• A minimum of 2 persons is required to assemble this product.
PARIS STORAGE BED 899684
Page 1 of 6

1. Attach 2 x side rails 3 to headboard 1 using 4 x
bolts (B), 4 x flat washer (F) and 4 x spring washer (I).
Tighten with Allen key (M).
1. Attach 2 x side rails 3 to footboard 2 using 4 x bolts
(B), 4 x flat washer (F) and 4 x spring washer (I).
Tighten with Allen key (M).
STEP ONE
FITTINGS
PARTS
Page 2 of 6

1. Attach 2 x wood leg 13 to footboard 2 using 4 x
bolts (A), 4 x flat washer (F) and 4 x spring washer (I).
Tighten with Allen key (M).
1. Attach central support rail 11 to headboard 1 and
footboard 2 with 4 x bolts (B), 4 x flat washers (F) and
4 x spring washers (I). Tighten with Allen key (M).
2. Attach central support leg 12 to central support rail
11 using 2 x bolts (C), 2 x nuts (E) and 4 x flat washers
(J). Tighten with a crosshead screwdriver and
spanner (N).
1. Attach drawer support rail 4 to side rail 3 with 8 x
bolts (A), 8 x flat washers (F) and 8 x spring washers
(I). Tighten with Allen key (M).
1. Attach drawer cross bar 5 to drawer support rail 4
with 2 x bolts (A), 2 x dowel (D), 2 x flat washers (F)
and 2 x spring washers (I). Tighten with Allen key (M).
STEP FOUR
STEP THREE
STEP TWO
Page 3 of 6

1. Insert slats 14 into end caps (L) and double end
caps (K) as shown.
2. Insert each end cap into corresponding holes in 2 x
side rails 3 and central support rail 11. Repeat
process for each slat.
NOTES:
* The curve of the slat must be facing upwards.
* Number of slats and caps vary dependant on size.
Quantities as shown in FITTINGS and PARTS
sections.
Note: Double 13 x Slats
King 14 x Slats
Super King 14 x Slats
1. Carefully slide drawer bottoms 9 into each
previously assembled drawer frame.
2. Insert 2 x wooden dowels (D) into drawer strength
rail. Attach drawer strength rail 10 to drawer back 8.
Repeat for second drawer frame.
STEP SIX
STEP SEVEN
1. Insert 4 x cam bolts (G) into 2 x drawer sides 6 and
tighten with a screwdriver.
2. Insert 2 x wooden dowels (D) into the 2 drawer
sides 6.
3. Attach drawer sides 6 to drawer back 8. Insert 4 x
cam locks (H) into drawer back 8 and tighten with a
screwdriver (not supplied).
4. Repeat previous steps to assemble the second
drawer frame using the remaining drawer sides 6 and
drawer back 8.
STEP FIVE
Page 4 of 6

Insert the assembled drawers into the bed.
1. Insert 4 x cam bolts (G) into drawer front 7 and
tighten with a screwdriver. Insert 2 x wooden dowels
(D) into drawer front 7.
2. Insert 2 x wooden dowels (D) into drawer strength
rail and attach drawer front 7 to assembled drawer
frames.
3. Insert 4 x cam locks into drawer sides 6 and tighten
with a screwdriver.
4. Repeat previous steps for the second drawer.
STEP NINE
STEP TEN
STEP EIGHT
Page 5 of 6

Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6