Next SPARKLE 849932 User manual

Tools Needed
Helpline
If you have any problems with this product please contact
Customer Services Tel: [phone]
• Assemble this product close to the required position in the room to reduce handling.
• All assembly fittings should always be tightened properly.
• This product contains 5 mm annealed mirror glass.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Avoid keeping furniture in direct sunlight or close to any heat source as this can cause cracking, discoloration or warping.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Do not place very hot or very cold items against or in proximity to mirror surface.
• Do not strike the glass with hard or pointed items.
• This item contains glass. Please handle with extreme care.
• This item contains glass. Please handle with extreme care.
• BS 744 : 1 1.
• Batch No.:2012/03
• This product contains 5 mm annealed glass. If the glass is chipped or broken replace with glass of the type described. Consult the
manufacturer, retailer or agent with regard to obtaining a manufacturing specification and shape for replacement glass quoting the model
number and batch number or date of manufacture.
PRODUCT INFORMATION
• Made from MDF and mirror glass
• Made in China
CARE INSTRUCTIONS
FITTINGS
GLASS INFORMATION
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty. Should
you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by step instructions.
• Carefully check that you have all the parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from construction area.
• Wall fixing are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
SPARKLE TRIPLE CABINET

1. Attach 2 x panels 3 to panel 4 as shown in the diagram.
1. Insert 4 x wooden dowels (E) into 2 x panels 3.
2. Attach panels 1 & 2 to 2 x panels 3 as shown.
STEP TWO
STEP THREE
1. Insert 4 x screws (A) into panels 1 & 2 using a
screwdriver to tighten.
PARTS
STEP ONE

1. Insert wooden dowels (E) into panel 5 as shown.
3. Attach panel 5 to the assembled unit as shown.
3. Slide panel 6 into the back panel grooves as shown.
1. Insert wooden dowels (E) into panel 7.
STEP FOUR
STEP FIVE
STEP SIX
2. Insert 4 x cambolts (C) into panel 5 using a screwdriver
to tighten.
1. Insert 4 x camlocks (D) into panel 1 & 2 using a
screwdriver to tighten.
2. Insert 4 x cambolts (C) into panel 7 using a screwdriver
to tighten.
3. Turn the panel 7 upside down and attach panel 7 to the
assembled unit.
2. Insert screw (A) into panel 5 by using a screwdriver to
tighten.
4. Insert screw (A) into panel 7 using a screwdriver to
tighten.

STEP SEVEN
1. Attach 2 x hinges (F) to panel with 4 x screws (B) by
using a screwdriver to tighten.
STEP EIGHT
STEP NINE
1. Insert 4 x camlocks (D) into panel 1 & 2 using a
screwdriver to tighten.
1. Attach panel 8 to panel 2 with 6 x screws (B) by using a
screwdriver to tighten.

2. Adjust the door properly as below illustration.
LATERAL
VERTICAL
FRONT TO
BACK
2. Use a spirit level to check that the marks are level.
WARNING:
Always ensure intended wall area to be drilled is free from
hidden electrical wires, water and gas pipes. Wall fixings
are not included, please ensure wall fixings are suitable
for your wall type. If in doubt consult a qualified
tradesperson.
4. Lift the cabinet into position ensuring that the fixing
clips attached to the cabinet are firmly hooked over the
screw threads. Check the mirror periodically to see that
no fitting has loosened and needs attention.
Next Retail Ltd, Desford Road, Leicester, LE1 4AT
STEP NINE
STEP ELEVEN
1. Attach panel to panel 4 with 4 x screws (B) by using a
screwdriver to tighten.
STEP TEN
3. Drill four holes and insert an appropriate wall plug into
each. Insert the screws and tighten, leaving the screw
head exposed by about 1/4 inch(6mm)
1. Attach panel 10 to panel 1 with 6 x screws (B) by using
a screwdriver to tighten.
2. Use 14 x stickers (G) to cover the visible camlock and
screw holes.
1. Use the template provided to mark on the wall the
position of the fixings.
NOTE: Place the template over the back of the cabinet to
ensure the holes line up with the hooks before drilling into
your wall.