Next LEAMINGTON User manual

r
Tools Needed
Helpline
If you have any problems with this product or
require
any replacement fittings please contact Customer
Services Tel: [phone]
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found
to be faulty. Should you need to return the unassembled product, please repack in the original packaging
IMPORTANT
• A minimum of persons persons is required to assemble this product.
PRODUCT INFORMATION
• Made from steel witha nickle powder coated finish and poplar sprung wooden slats.
• Carefully check that you have all parts before beginning assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Do not use abrasive cleaning products or those containing silicone.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage.
• Do not rub or scrub the surface when cleaning.
• Made in China.
CARE INSTRUCTIONS
• For general cleaning, periodically dust with a soft cloth.
• Do not put hot dishes directly on the surfaces of the item.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
LEAMINGTON BED
(SINGLE)
Page 1 of 4

FITTINGS
PARTS
A.Bolts x 8
M6X20mm
B.Plastic Washer x 8
M6
D.Allen key x 1
4mm
C.Metal Washer x 12
M6
(1)Headboard x 1
(2)Footboard x 1
(3)Side Rail x 2
(4)Sprung Slats x
(5)Plastic cap
(one end open)
(6)Finials x
(7)Fabric Strap x
E.Bolts x 4
M6X40mm
(9)Foam Pads x 4
(8) Foot Slider x
Page 2 of 4

1. Insert 1 x sprung wooden slat (4) through the first
hole in strap (7).
2. Attach single sided slat cap (5) onto one end of
the sprung wooden slat(4).
3. Insert sprung wooden slat and slat cap fitting from
Step 1 & 2, into the first gap in side rail 3.
4. Attach 1 x single sided slat cap (5) to the other
side of the slat and by lifting the centre and pushing
down on the end, insert the end of the slat (with
fitted cap) into the corresponding hole on the other
5. Repeat process for all remaining slats and caps
until all components have been used and firmly
pushed in place.
STEP THREE
STEP ONE
1.Attach Foot Slider (8) to Headboard 1 and
Footboard 2
by using Bolts (E), Metal Washer (C)and tightening
with
Allen key (D). Peel the rear tape from the Foam Pads
(9)
1. Attach side rails 3 (x2) to headboard 1 and
footboard 2 using 8 x bolts (A), 8 x plastic washers
(B)
and 8 x metal washers (C). Tighten using Allen key
(D).
STEP TWO
Page 3 of 4

1. Attach 4 x finials (6) to headboard 1 and
footboard 2 turning clockwise by hand to tighten.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
STEP FOUR
Page 4 of 4