Next STANTON 138678 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0333 777 8999
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
138678 STANTON PHONE TABLE
138678 STANTON PHONE TABLE 138678 STANTON PHONE TABLE
138678 STANTON PHONE TABLE
• Wall fixings are not included.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• We recommend the use of the wall attachment bracket/strap provided for safety reasons.
• Made in China.
• A minimum of two persons is required to assemble this product.
• Made from partical board & MDF with a wood effect finish.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or
warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Do not rub or scrub the surface when cleaning.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft cloth.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
Page 1 of 6

1.Insert 14 x cambolts (D) into panels 1 , 2 , 3 & 5
and tighten with a screwdriver.
FITTINGS
PARTS
STEP ONE
D
2.Attach panel 7 to panel 3 with 2 x screws (E) and
tighten with a screwdriver.
STEP TWO
3
E
7
3
D
D
DD
1
2
5
Page 2 of 6

1.Glue and insert 1x wooden dowel (A) into panel 6
2.Attach panel 6 to panel 4.
3.Insert 2 x camlocks (C) into panel 4 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
1.Glue and insert 4 x wooden dowels (A) into panel 2.
2.Attach panels 4 , 5 & 6 to panel 2.
3.Insert 4 x camlocks (C) into panels 4 , 5 & 6 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP THREE
STEP FOUR
4
B
6C
A
C
5
6
1.Glue and insert 4 x wooden dowels (A) into panels 4 , 5
& 6
2.Attach panel 1 to panels 4 , 5 & 6
3.Insert 4 x camlocks (C) into panels 4 , 5 & 6 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP FIVE
B
A
1
B
C
A
6
4
5
Page 3 of 6

1.Carefully lift the unit upright.
2.Slide panel 8 into the grooves of the assembled unit
1.Glue and insert 4 x wooden dowels (A) into panels 1 & 2
2.Attach panel 3 to panels 1 & 2
3.Insert 4 x camlocks (C) into panels 1 & 2 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP SEVEN
STEP SIX
A
3
1.Insert 4× metal pins (H) in required position
2.Insert shelf 9 into the assembled unit
STEP EIGHT
A
1
2
finishedside
Page 4 of 6

1.Attach panels 11 & 12 to panel 13 with 4 x screws (E),
and tighten with a screwdriver.
1.Slide panel 14 into the grooves of the drawer frame.
STEP TEN
STEP NINE
1.Insert 2 x cambolts (D) into panel 10 and tighten
with a screwdriver.
2.Glue and insert 2 x wooden dowels (G) into panels 11 &
12
3.Attach panel 10 to the assembled drawer frame.
4.Insert 2 x camlocks (C) into panels 11 & 12
and tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
5. Attach 1x handle(F) to the panel 10 with 1x bolt (F) to
tighten with a screwdriver.
STEP ELEVEN
Page 5 of 6

1. Insert the drawer 10 to the assembled unit as shown in
diagram.
Note: If you want to disassembled the unit,
please follow the steps as the right
brief to push the drawer out.
1. Insert 6x plastic fasteners (I) into the back panel
grooves and tighten with screws provided.
2.Using screw and washer secure the
1X nylon strap (J) to the back of top panel .
3.Secure the other end of the strap to the
wall with an appropriate screw and wall
plug for your wall type (not provided).
To hide the strap behind the unit, drill the
hole lower than the top of the unit.
Warning:
Always ensure intended wall area to
STEP TWELVE
STEP THIRTEEN
I
Always ensure intended wall area to
be drilled is free from hidden electrical
wires, water and gas pipes.
NB:Wall fixings are not included - please
source suitable fixing for your wall type.
If in doubt please consult a qualified
trades person.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 6 of 6