Next CARTER 117994 User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel: 0844
844 8999
• WARNING: Do not use child's bed neat if any part is broken ,torn or missing and use only spare parts approved by the manufacture
• All assembly fitting should be tightened properly before use and should be periodiacally checked and re-tightended if required.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Children are likely to play,bounce jump and climb on beds,therefore the child's bed should not be place too close to other furnture
• A minimum of two persons is required to assemble this product.
• A mattress measuring 900mm x 1900mm is intended for use with this item
• Assemble this product close to the required position in the room to reduce handling.
PRODUCT INFORMATION
• Made from MDF & particle board with a wood effect finish paper.
• WARNING: Not suitable for children under 4 years.
• WARNIMG: Be aware of the rish of open fire and other sources of strong heat,such as electric bar fires,etc.In near vicinity of the bed
• WARNING: Do not place this child's bed near heat sources,windows and other furniture
• Do not put hot dishes directly on the surfaces of the item.
• For general cleaning, periodically dust with a soft cloth.
CARE INSTRUCTIONS
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be faulty.
Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - KEEP FOR FUTURE
REFERENCE READ CAREFULLY
• Keep fittings out of children's reach and keep children well away from the construction area.
• Made in China.
• Do not use furniture polish.
• Do not rub or scrub the surface when cleaning.
• Sprung slates are designed to be positioned with the curve ︵
︵︵
︵ not ︶
︶︶
︶ .Incorrect use may cause damage to the bedstead.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or damage.
• Do not cover your bed straight away-allow it to air thoroughly for a few hours.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• The child's bde conforms to BS 8509:2008+A1:2011
•The bed is not designed to be dismantled for storage or transportation.
117994 CARTER BED
Page 1 of 4

1. Insert 4 x bolts (D) into nuts fixed on panel 2 and turn bolts (D)
clockwise until tight by hands.
STEP ONE
PARTS
FITTINGS
Page 2 of 4

STEP TWO
1. Glue and insert 4 x wooden dowels (A) into panels 3 & 4.
2. Insert 4 × nuts (J) into panels 3 & 4.
3. Attach panels 3 & 4 to panel 1 with 4 x bolts (K) and tighten by
an Allen key (L).
STEP THREE
1. Glue and insert 4 x wooden dowels (A) into panels 3 & 4.
2. Attach panel 2 to panels 3 & 4.
3. Cover 4 x metal pieces (E) onto 4 x bolts (D) and thread 4 x
springs (F) onto bolts (D) then screw 4 x metal nuts (C) with
spanner (G) to tighten.
STEP FOUR
1. Attach panel 5 to panels 3 & 4 with 4 x screws (I) and tighten
with a screwdriver.
Page 3 of 4

STEP FIVE
1. Insert 16 x slats 6 into the gap of nylon strap (N) as shown in
diagram
STEP SIX
1. Insert 32 x plastic sleeves (H) to slats 6.
STEP SEVEN
1. Attach slats 6 to panels 3 & 4 as shown in diagram.
2. Use 4 x stickers (M) to cover the holes on panel 1.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
6
Page 4 of 4