Next STANTON 932185 User manual

Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: [phone]
CARE INSTRUCTIONS
•For general cleaning, periodically dust with a soft clean lint-free cloth or a soft micro fibre cloth.
• Do not rub or scrub the surface when cleaning.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• All assembly fixings should be tightened properly. Periodically check all fixings and tighten if necessary.
• Any spills should be removed immediately with a soft clean lint-free cloth or micro fibre cloth and dried
immediately.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent
scratching or damage. Ensure the mats and coasters used do not have an abrasive surface underneath.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration
or warping.
• Keep fittings out of children's reach and keep children well away from the construction area.
• We recommend that the packaging is used to protect the surfaces during assembly.
• Made in China.
• Made from engineered board with a wood effect finish.
PRODUCT INFORMATION
• A minimum of two person is required to assemble this product.
• Carefully check that you have all parts before beginning assembly.
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is
found to be faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
932185 STANTON COFFEE TRUNK
Page 1 of 6

1. Insert cambolts(A) into panel (1)&(3)&(4) & (8)x2
by using a screwdriver until tight .
2. Insert cambolts(C) into panel(13) by using a
screwdriver until tight .
FITTINGS
PARTS
*NOTE: 2 spare camlocks are included in case a failure during assembly.
STEP ONE
18x
2
Page 2 of 6

1. Glue and insert wooden dowels (E) into panel (2).
2.Attach panel(8)x2 to panel(2) with camlocks (B)
by using a screwdriver until tight.
Ensure the arrow indicator is pointing towards
the panel edge and turn camlocks clockwise
until tight using a screwdriver.
1. Glue and insert wooden dowels (E) into panel (14).
2.Attach panel(14) to panel(2) with bolts (M) by using
an Allen Key(G) until tight.
1. Glue and insert wooden dowels (E) into panel (5).
2. Attach panel (5) to panel (2) with bolts(M) with an
Allen Key(G) until tight.
STEP THREE
STEP FOUR
STEP TWO
8
2
5
2
Page 3 of 6

1. Glue and insert wooden dowels (E) into panel (2).
2.Attach panel (4) to panels(2)&(7)x2 with
camlocks(B) by using a screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and turn camlocks clockwise until tight
using a screwdriver.
1. Glue and Insert wooden dowels (E) into panel (2).
2.Attach panel (3) to panel (2)&(7)x2 with
camlocks(B) by using a screwdriver.
Ensure the arrow indicator is pointing towards
the panel edge and turn cam locks clockwise until
tight using a screwdriver.
1.Stand the unit upright carefully.
2.Slide panels(15)x2 into groove of the assembled
unit as shown.
STEP SIX
STEP SEVEN
STEP FIVE
2
7
7
2
7
4
2
4
5
15
15
3
Page 4 of 6

1.Glue and insert wooden dowels (E) into panel (3)
& (4) &(5).
2.Attach panel(1) to panel (3)&(4)&(5) with
camlocks(B) by using a screwdriver.
Ensure the arrow indicator is pointing towards
the panel edge and turn cam locks clockwise
until tight using a screwdriver.
3.Attach panel(7) x2 to panel(1) with screws(J) by
using a screwdriver until tight.
4.Use the sticker(K) to cover camlock holes.
1. Glue and Insert wooden dowels (E) into panel(11).
2.Attach panel(9)&(10) to panel(11) with 4x screws(J)
by using a screwdriver until tighten.
3.Slide panel (12) into groove of the assembled unit.
1.Attach handles(H)to panel(13) with screws(I) by
using a screwdriver until tight.
2.Glue and insert wooden dowels(E) into panels (9)
& (10).
3.Insert camlocks (D ) into panels (9)& (10) with a
screwdriver.
Ensure the arrow indicator is pointing towards the
panel edge and turn cam locks clockwise until
tight using a screwdriver.
4. Use stickers(K) to cover camlock holes.
5. Repeat STEP 9 to 10 to assemble another drawer.
STEP EIGHT
STEP TEN
STEP NINE
11
12
10
11
I
13
1
3
5
4
2
7
Page 5 of 6

1.Insert shelf pins(F)into the assembled unit
as shown.
Ensure all shelf pins are at the same height for
each shelf.
2.Place adjustable panels (6)x2 onto shelf pins in
each cupboard.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
1.Put the drawers into the assembled unit as shown.
STEP ELEVEN
STEP TWELVE
6
6
13
13
Page 6 of 6