Next STANTON User manual

Tools Needed
Helpline
If you have any problems with this product or require any
replacement fittings please contact Customer Services Tel:
0333 777 8999
ASSEMBLY INSTRUCTIONS.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found to be
faulty. Should you need to return the unassembled product, please repack in the original packaging.
IMPORTANT
• Carefully check that you have all parts before beginning assembly.
• We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
STANTON TV UNIT
STANTON TV UNITSTANTON TV UNIT
STANTON TV UNIT
• We recommend that the packaging is used to protect the surfaces during assembly.
• Keep fittings out of children's reach and keep children well away from the construction area.
• Carefully check that you have all parts before beginning assembly.
• A minimum of two persons is required to assemble this product.
• Made from partical board & MDF with a wood effect finish.
CARE INSTRUCTIONS
PRODUCT INFORMATION
• Made in China.
• Never drag pieces of furniture across the floor as this will cause damage to the joints.
• Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or warping.
• Any spills should be removed immediately with a soft clean damp cloth and dried immediately.
• Do not put hot dishes directly on the surfaces of the item.
• Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching or
damage.
• Do not use furniture polish.
• For general cleaning, periodically dust with a soft cloth.
• Do not rub or scrub the surface when cleaning.
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.
Page 1 of 6

FITTINGS
PARTS
DX16
CX16
BX2AX17 EX1
(?8*30mm)
FX4 GX8 HX7 IX2 JX1
(4*38m/m)
1.Attach panels 13 & 14 to panel 15 with
4 x screws (H), and tighten with a screwdriver.
STEP ONE
H
13
15 14
Page 2 of 6

1.Slide panel 16 into the assembled unit.
1.Insert 2 x cambolts (D) into panel 12 and tighten
with a screwdriver.
2.Glue and insert 4 x wooden dowels (A) into panels 13 &
14.
3.Attach panel 12 to the assembled drawer frame.
4.Insert 2 x camlocks (C) into panels 13 & 14
and tighten with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP TWO
STEP THREE
13
12
A
B
C
D
D
1. Attach 1x handle(E) to the panel 12 with 1x bolt (E)
and tighten with a screwdriver.
STEP FOUR
14
13 A
B
C
12
E
Page 3 of 6

1.Insert 14 x cambolts (D) into panels 1,2,3, 5 & 6 and
tighten with a screwdriver.
2.Attach panel 4 to panel 1 with 3 x screws (H),and
tighten with a screwdriver.
1.Glue and insert 3 x wooden dowels (A) into panel 2
2.Attach panels 3 & 11 to panel 2.
3.Insert 4 x camlocks (C) into panels 2 & 11 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP FIVE
STEP SIX
11
3
C
1
4
2
6
H
H
finished side
D
D
D
D
3
1.Glue and insert 4x wooden dowels (A) into panel 2
2.Attach panels 5 & 6 to panel 2
3.Insert 4x camlocks (C) into panel 2 and tighten with a
screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
4.Attach panel 7 to panel 2 with 2 x screws (I) with an
Allen key ( J) to tighten
STEP SEVEN
2
C
C
A
B
2
7
5
6
A
B
Page 4 of 6

1.Slide panels 9 & 10 into the assembled unit as the
illustration.
1.Glue and insert 6 x wooden dowels (A) into panels 5, 6
& 7
2.Attach panel 1 to panels 5, 6 & 7.
3.Insert 6x camlocks (C) into panels 5,6 & 7 and tighten
with a screwdriver.
Ensuring the arrow indicator is pointing towards the
panel edge before tightening with a screwdriver.
STEP EIGHT
STEP NINE
10
1
panel edge before tightening with a screwdriver.
1.Insert 4 x fittings (P) into the required position
2.Insert panel 8 onto the fittings (P) .
STEP TEN
8
finished side
B
1
5
7
6
Page 5 of 6

1. Insert the drawer 12 to the assembled unit as
shown in diagram.
Note: If you want to disassembled the unit,
please follow the steps as the right
brief to push the drawer out.
1.Secure 8× plastic fasteners (G) with screws (G)
provided onto the back panel.
STEP ELEVEN
STEP TWELVE
12
provided onto the back panel.
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
G
G
Page 6 of 6