NEXTIVITY Cel-Fi GO+ User manual

Cel-Fi Indoor
Omni Antenna
A52-V32-100
Cel-Fi Wideband
Panel Antenna
A11-V43-100
Cel-Fi Wideband
Directional Antenna
A32-V32-100
Cel-Fi Mobile Mag
Mount Antenna
A41-V21-100
A41-V21-101
Cel-Fi Mobile Bolt
Mount Antenna
A41-V36-100
A41-V36-101
Cel-Fi Whip
Antenna
A21-V33-100
Cel-Fi Mobile
Server
Antenna
A41-V30-100
Cel-Fi Mount
Antenna
A62-V44-100
Cel-Fi Trucker
Antenna
A21-V31-100
Cel-Fi Marine
Antenna
A11-V37-100
Cel-Fi
Antenna
Mount
F66-100
Cel-Fi
Pole Mount
F26-100
User Interface
qsg_go+-eng_19-0730
Cel-Fi GO+ All-in-One
Quick Start Guide
Smart Signal Booster™
Basic Functionality
The Cel-Fi GO+ All-in-One Smart
Signal Booster Smart Signal
Booster is designed to improve
cellular coverage in a building,
remote area, or vehicle. Cel-Fi
GO+ connects to an external
Donor Antenna to draw in a cellular signal from the macro
network, and redistribute signal via the Server Antenna.
Cel-Fi WAVE App
The Cel-Fi WAVE app provides a User
Interface to Cel-Fi systems. The app’s
dashboard shows the system “Boost”
value that is a numeric representation
mapped to the amount of Signal Gaivn the
system is providing. Higher is better, with
nine (9) being the highest value. Cel-Fi
WAVE is the registration and management
application that allows users to setup
antenna, modes, and carriers. Cel-Fi WAVE
app is available through either the Google
Play Store or Apple App Store; depending
on the mobile device.
Cel-Fi GO+ is congured to automatically select the best
cellular band to boost.
• A user may manually congure the system’s preferences
using the Cel-Fi WAVE app.
• A user may manually change the system’s Carrier cong
and Mode between Mobile and Stationary via
Cel-Fi WAVE app.
NEMA 4 Rating
The Cel-Fi GO+ is NEMA 4 rated, and can be used both
indoors and outdoors. The NEMA 4 rating provides the
following advantages:
• A degree of protection against ingress of solid foreign
objects (falling dirt and windblown dust)
• A degree of protection from the ingress of water (rain,
sleet, snow, splashing water, and hose directed water)
• Equipment will be undamaged by the external formation
of ice on the enclosure
Review the latest authorized antennas at www.cel-.com/antennas
Antenna and Mount Options:
LED MEANING
Solid GREEN The unit is working properly and boosting properly.
Blinking GREEN Unit is scanning for networks to boost.
Blinking RED The unit is in an error condition. Use the Cel-Fi WAVE app to
check the error code meaning and remedy.
Solid RED The unit has a hardware error and is not booting up normally.
Cel-Fi GO+ All-in-One Smart Signal Booster features an LED on the top face
to indicate the unit’s state:
NOTE: In mobile usage, it is normal for the Cel-Fi GO+ All-in-One Smart
Signal Booster to uctuate between scanning and boosting. The Cel-Fi GO+
All-in-One Smart Signal Booster automatically adjusts its boost behavior
based on available signal.
ISSUE MEANING ACTION
Continual
Blinking
GREEN
Unit is
operational, but
not attaching to a
network to boost.
• Make sure both antennas are connected
properly and are appropriate for the desired
frequencies to boost.
• Make sure the selected operator to relay is
available at your location. This can be checked
with the Cel-Fi WAVE application. If the service
is not available, it cannot be boosted.
Solid
RED LED
Unit is not
operational.
• Unplug and reinsert power.
• If restart has no effect, contact vendor for
remedy.
Troubleshooting
Specifications:
Frequency Support Multiple variations of the product are available with
different frequency support.
Model:
 G32-2/4/5/12/13
BAND NAME DOWNLINK UPLINK
21900 PCS 1930 1990 1850 1910
4AWS–1 2110 2155 1710 1755
5850 869 894 824 849
12 700 a 729 746 699 716
13 700 c 746 756 777 787
Gain Up to 100 dB system gain
Model:
G32-1/3/5/7/8/20
BAND NAME DOWNLINK UPLINK
1 2100 2110 2170 1920 1980
3 1800+ 1805 1880 1710 1785
5 850 869 894 824 849
7 2600 2620 2690 2500 2570
8 900 925 960 880 915
20 800 DD 791 821 832 862
Gain
Up to 100 dB system gain
Dimensions
LENGTH WIDTH HEIGHT WEIGHT
272.5 mm 96.5 mm 43.5 mm 850 g
Power (max)
DOWNLINK TX UPLINK TX
10 dBm/5 MHz
(16 dBm per band) 24 dBm per band
Bluetooth (LE Ver 4.2) FREQUENCY POWER
2042 – 2480 MHz 0 dBm
Environmental
Operating Temp: 0 - 65°C
Relative Humidity: 95%
Antenna Connectors SMA-Female
 Certications 3GPP TS 25.143 Rel.10 BQB (Bluetooth)
(All variants) 3GPP TS 36.143 Rel.10 NEMA-4
RoHS 2
(G32-2/4/5/12/13 FCC CSA C22.2#62368-1
variants only)ISED UL 50E, UL 60950-22
UL 62368-1:2014 CSA C22.2#60950-22
(G32-1/3/5/7/8/20 IEC 62368-1:2014 EN 301 908-1 v11.1.1
variants only) EN 301 489-1 v2.1.1 EN 301 908 v11.1.2
EN 301 489-17 v3.1.1 EN 301 908 v11.1.2
EN 301 489-50 v2.2.0 EN 300 328 v2.1.1
EN 62311 (2008)
Regulation (EC) 1275/2008 (Standby and Off mode)
Regulation (EC) 278/2009 (External Power Supply)
Cel-Fi GO+ All-in-One Smart Signal Booster

Before You Begin
Cel-Fi GO+ All-in-One Smart Signal Booster has a Donor Antenna Port and a
Server Antenna Port. They are marked on the device with icons (see illustration).
It is critical that the Donor and Server antennas are connected to the correct port.
IMPORTANT: Best to make sure all cable lengths support the intended mounting
location BEFORE permanent mounting.
Cel-Fi GO+ All-in-One
Smart Signal Booster
Installation SERVER DONOR
Cel-Fi GO+ All-in-One Smart Signal Booster
Change Modes Between Mobile
(65/70dB)orStationary(100dB)
1. Open Cel-Fi WAVE application
2. Go to settings tab
3. Select Booster Setting
4. Switch between mobile and stationary
ChangeCarrier/Operator
1. Open Cel-Fi WAVE application
2. Go to settings tab
3. Select Operator
4. Switch between mobile network operators
Change Between Modes and Carriers
IMPORTANT: Cel-Fi GO+ All-in-One Smart Signal
Booster ships with a mode and operator selected,
but some versions can be changed via Cel-Fi WAVE.
Install Server
Antenna*
*Sold Separately
2Connect Donor
& Server Antennas
to the Cel-Fi GO+
4Activate &
Setup with
Cel-Fi WAVE
6
Mount
Cel-Fi GO+
3An AC or
12V Power
Source
5
Install
Donor
Antenna
1
4
1
2
5
3
2
3
1
5
4
1
3
5
22
4
06:00 PM
5
1
2
3
4
5
2
1
3
4
Point & Optimize Antenna
For stationary applications, Cel-FiGO+XIndoor/
Outdoor Solution with AntennaBoost integrates
the Cel-Fi Antenna with the Cel-Fi WAVE Platform
to provide the best donor signal in the industry.
Nextivity’s proprietary 8-position dial base enables
the antenna to be rotated in 45-degree increments
for best performance, optimized with real time data
from the Cel-Fi WAVE Antenna Position Test.
Install Tips for Donor Antenna
• Install antenna at least 12 inches from any other antennas for
best performance
• Antenna should be free of obstructions
• Antenna should be away from windows (including sunroof or
other openings)
• Install 8 inches away from any people
• For best performance make sure there is 50 cm of metal
around the base of the antenna
Install Tips for Server Antenna
• For best results, install Donor and Server Antennas such that
there is substantial material between the antennas. This will
create isolation and allow the system to perform at higher gain
without oscillation or feedback
• Keep Donor and Service Antennas separated/isolated from
each other for best performance
• Do not use cable splitters for Donor Antennas
• Follow the installation instructions for your chosen antennas
• The power supply is not NEMA 4 rated
Tips for Mobile Mounting:
• Location should have airow (for cooling) and be secure from
contact with external objects
• Make sure the unit is within cable range of the 12V power
supply on your vehicle
2
2
1
3
3
4
5
Antenna
Antenna Mount
1
2
3
4
5
6
7
8
8-Position Dial
Position
Set Screw
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Position
Arrow
» https://www.signalbooster.com/pages/contact-us
» [email protected]
» 1-855-846-2654