Nibe Contura C750A User manual

Installation
Instructions
C750
C750A
www.contura.eu
For more information go to www.ecobuildproductsearch.co.uk

GB
50
Manufacturer’s assurance
The stove is approved by the Swedish National Testing and Research Institute, SP SITAC and fulfils
the applicable rules for CE marking. Manufacture of the product has taken place in accordance with
those documents that are the basis for the relevant type approval certification and the required
manufacturing checks.
378 001
N
O
R
D
I
C
E
C
O
L
A
B
E
L
378 001
N
O
R
D
I
C
E
C
O
L
A
B
E
L
Contura 750 is a Swan marked wood burning stove.
NIBE was the first stove manufacturer in Sweden to commit to Swan marking stoves. The Swan mark
is one aspect of our vision to be a company of the future, setting high quality standards regarding
the environment. Certification number 378-001.
CERTIFICATE
www.contura.eu
EC Declaration of
conformity
MANUFACTURER
Name NIBE AB/NIBE STOVES
Address Box 134, Skulptörvägen 10, SE-285 23 Markaryd
Place of manufacture Markaryd, Sweden
PRODUCT
Product type Stove fired by solid fuel
Type designation Contura
Standard EN 13240 annex ZA
Intended for use Heating of living accommodation
Fuels Wood logs
Special conditions None
CE-MARKING 750/750A
Issued 2010
Nominal output 5 kW
Fuel type Wood logs
Flue gas temperature 271° C
Energy efficiency 80%
Emission of CO 0,1%
Appendix
Lighting and installation instructions
Niklas Gunnarsson
Business area manager NIBE STOVES
For more information go to www.ecobuildproductsearch.co.uk

GB
51
Table of contents
Technical details 52
Prior to installation 52
Connection to chimney 53
Supply of combustion air/Option 54
Installation distance 750 55
Installing 750 56
Removing the loose parts 58
A warm welcome to Contura.
A warm welcome to the Contura family. We hope
you will get a great deal of pleasure from your new
stove. As a new owner of a Contura stove you have
secured a product with timeless design and long
service life. Contura also has combustion that is both
environmentally friendly and efficient for the best heat
production.
Read through these installation instructions carefully
before installation. Read how to best light your stove
in the lighting instructions.
The stove becomes very hot
During operation, certain surfaces of the stove become
very hot and can cause burn injury if touched. Be aware of
the strong heat radiated through the hatch glass. Placing
flammable material closer than the safe distance indicated
may cause a fire. Pyre lighting can cause quick gas ignition
with the risk of damage to property and personal injury.
NOTE! WARNING!
Report the installation of a stove to your
local authority.
The owner of the house is personally responsible
for ensuring compliance with the mandatory safety
requirements and must have the installation approved by
a qualified inspector. Your local chimney sweep must also
be informed about the installation as this will affect the
routines for regular chimney-sweeping services.
CONTENTS
For more information go to www.ecobuildproductsearch.co.uk

GB
52 FACTS
Output 3-7kW
Nominal output 5 kW
Efficiency up to 80%
Model 750
Height (mm) 1151
Width (mm) 459
Depth (mm) 372
Weight (kg) 103
Type approved in accordance with:
European standard EN-13240
Swedish type approval
Norwegian standard NS 3059, SINTEF - 110-0354
German standard DIN Plus, RRF - 40112559
Contura 750
Prior to installation
If the insert needs to be put down
to be moved or if the pillar foot is
to be installed, remove any loose
components. This is described at the
end of these installation instructions.
1 Fire bars
2 Grate disc
3 Heat deflector
4 Hearth cladding
1
2
3
4
Installation by authorised
technician
This manual contains instructions about
how the stoves must be assembled and
installed. To ensure the function and safety
of the stove, we recommend that the
installation is carried out by an authorised
technician. Contact one of our dealers who
can recommend suitable technicians.
Building application
These main insructions may give guidance
which would contravene national building
regulations. Please refer to supplementary
instructions or ask your local authority for
advice regarding building regulations.
Before installing a stove or erecting a
chimney it is necessary for you to make
a building application permission to your
local authority.
Structural support
Check that the wood joists are strong
enough to bear the weight of the stove and
chimney. The stove and chimney can usually
be placed on a normal wooden joist in a
single occupancy house if the total weight
does not exceed 400 kg.
Hearth plate
Due to the risk of falling embers, a
flammable floor must be protected by a
hearth plate. It must extend 300 mm in
front of the stove and 100 mm on each side
of the stove, or have a 200 mm extension
on each side of the opening. The hearth
plate can consist of natural stone, concrete,
metal plate or glass. A painted metal
or glass hearth plate is available as an
accessory for these models.
Important to remember!Technical details
For more information go to www.ecobuildproductsearch.co.uk

GB
53
CHIMNEY
Connection to chimney
12
Ø
ca 180 mm
Ø
ca 180 mm
Rear connection to a masonry chimney
Top connection to the chimney
Make sure that the connector
gasket does not work loose when
the connection pipe is placed
on the connector. If further
sealing material is required, heat-
resistant sealant may be used.
The back panel must be installed before the stove is rear connected.
The hot air grille must be installed before chimney top
connection.
• The stove meets the requirements for connecting to chimneys
dimensioned for 350°C flue gas temperature.
• The external diameter of the connection sleeve is 150 mm.
• The stove requires a draft in the chimney of at least –12 Pa. The
draft is affected both by the length and area of the chimney, and
by how well sealed it is. Minimum recommended chimney length
is 3.5 m and suitable cross section area is 150-200 cm² (140-160
mm in diameter).
• A flue with sharp bends and horizontal routing reduces the
draught in the chimney. Maximum horizontal flue is 1 m, on the
condition that the vertical flue length is at least 5 m.
• It must be possible to sweep the full length of the flue and the
soot hatches must be easily accessible.
• Carefully check that the chimney is sealed and that there is no
leakage around soot hatches and flue connections.
2 31
5 64
!
In the bag with these installation instructions
are two wing screws for the cover.
For more information go to www.ecobuildproductsearch.co.uk

GB
54 SUPPLY AIR/ACCESSORY
Supply of combustion air
When a stove is installed in a room, the demand for air supply to
the room increases. Air can be provided indirectly via a vent in
the outer wall or via a duct from the outside that is connected to
the connector on the underneath of the stove. The amount of air
needed for combustion is 25m3/h.
The connector has an external diameter of 67 mm. When duct
routing further than 1 m the pipe diameter must be increased to
100 mm and a correspondingly larger wall vent must be selected.
In hot areas the duct should be insulated with 30 mm mineral wool
covered with a moisture inhibitor (plastic). It is important that the
lead-in between the pipe and the wall (or floor) is sealed using
jointing compound.
A 1 m length of condensation insulated ducting for combustion air
is available as an accessory.
Through the external wall.
Indirect air supply through the external wall.
Through floor and foundation slab.
Through floor and wall-and-cavity foundation.
C750/750A
In the back and floor plates there are
knockouts that must be removed to insert
the pipe.
Installation variants
Leave a 40 mm gap between
the condensation insulation
and the bottom of the stove.
!
HK
HK
40 mm
HK
40 mm
HK
40 mm
For more information go to www.ecobuildproductsearch.co.uk

GB
55
INSTALLATION DISTANCES
D 433
459
1151
2100*
Combustible roof
372
176
A 1116*
178
B 1026*
C 420
38
Ø150
Air inlet Ø67
631
400
278
278
278
100
Combustible wall
250
445
706
250
826
Combustible wall
C750
* If the stove is placed on a hearth plate made of glass for example (accessory), the height from the floor is affected by a distance corresponding to the thickness of the hearth plate. Also applies to
separate glass hearth plates (accessory).
** We recommended the same side distance as to combustible walls to prevent discolouration of painted non-flammable walls.
281
50**
700
1100
228
50**
Fire-retardant wall of
brick or concrete
900
900
245
506
50**
543
Fire-retardant wall of
brick or concrete
The minimum distance in front of
the stove opening to combustible
parts of the building or interior
decoration must be at least 1 m.
The dimension diagrams only
show the minimum permitted
installation distances for the
stove. When connecting to a steel
flue, also note the safety distance
requirements of the flue. The
safety distance between an un-
insulated flue and a combustible
part of the building should be at
least 450 mm.
Installation distances
A = height from floor to chimney
connection upwards
B = height from floor to c/c chimney
connection rear
C = height from floor to air inlet
D = height from floor to lower edge
of hatch
Permitted
area for
combustible
material
A separate glass hearth
plate (accessory)
increases the connection
height to the chimney by
6 mm.
!
For more information go to www.ecobuildproductsearch.co.uk

GB
56 ASSEMBLY
Installing C750/750A
1
2
2
1
Clean the side glass
thoroughly before installing
the side panels.
3
Final inspection of the installation
!
It is extremely important that the installation is inspected by an authorised chimney sweep before
the stove is used. Also read the ”Lighting instructions”, before lighting for the first time.
For more information go to www.ecobuildproductsearch.co.uk

GB
57
ASSEMBLY
x4
4
6
5
For more information go to www.ecobuildproductsearch.co.uk

GB
58 REMOVAL
How to remove the hearth surround
Handle the vermiculite with care. Lift the smoke baffle with one hand whilst
removing the sides. The side posts need not be removed when sweeping.
Reinstall in reverse order
How to remove the heat deflector
2
1
For more information go to www.ecobuildproductsearch.co.uk

For more information go to www.ecobuildproductsearch.co.uk

811063 IAV SE-EX C750-5
NIBE AB/NIBE STOVES · Box 134 · SE-285 23 Markaryd
Sweden · www.contura.se
NIBE Stoves reserves the right to change colours, materials,
dimensions and models at any time without special notice. Your
dealer can give you the most up to date information. Stoves
shown in brochures may have optional extras.
For more information go to www.ecobuildproductsearch.co.uk