Nibe Contura Ci7 User manual

Ci7
C300
Lighting
Instructions
www.contura.eu
Eldningsinstruktion 2
Heizinstruktionen 7
Fyringsinstruksjon 12
Instructions d’allumage 17
Lighting Instructions 22
Fyringsvejledning 27
Lämmitysohjeet 32
Istruzioni per l’accensione 37
Stookinstructies 42
SE
DE
NO
FR
GB
DK
FI
IT
NL

GB
22
Lighting Instructions
The damper
Lighting Kindling:
Note that if too little kindling is used when lighting, or if the wood is too
thickly cut, the firebox will not reach the correct operating temperature.
Incorrect lighting can lead to poor combustion with heavy sooting and may
result in the fire going out when the door is shut.
If the fireplace is connected to outdoor air, it may be necessary to open a
window near to the fireplace prior to lighting. Leave the window open for a
few minutes until the fire has caught properly.
• The damper is opened by moving the control to the right.
• Close the damper when the fireplace is not in use to prevent the
room air flowing out and condensation building up in the chimney.
• Never close the damper before the embers have burnt out.
Finely chopped wood
Length: 25-33 cm
Diameter: 2 – 5 cm
Weight per lighting: 2.0 kg
(approx. 8-12 finely chopped pieces)
1. Open the control for the combustion air fully.
2. Stack the finely chopped wood crosswise in the firebox.
3. Place a firelighter in the middle of the stack of wood and light it.
4. Close the door. A slight amount of soot may build up on the glass during
the start-up fire. This is normal and vanishes after a period of time.
5. A fresh load of logs should not be put on until the start-up fire has
become a glowing bed of embers.
Your Contura fireplace is intended to produce secondary heating for the
accommodation. It is important that the correct amount of wood is used,
especially when lighting. If you are lighting the fire for the first time, you
should use a set of scales to see how much 2.0 kg kindling is. Also check
what the normal and maximum weights look like.
The fireplace may only be lit with the door closed.
Always open the door carefully and slowly to prevent blow back because of
the changing pressure in the firebox.
Combustion is affected by the draft in the chimney and the quality of the
wood. Achieving the correct setting for the combustion air damper, suitable
size and amount of wood usually takes a few attempts.
Lighting in the right way

GB
23
Lighting Instructions
All types of wood, such as birch, beech, oak, elm, ash, conifers and fruit
trees can be used as fuel in the fireplace. Different types of trees have
different densities; the greater the density of the wood, the greater the
energy value. Oak, beech and birch have the highest density.
Lighting for the first time
The wood’s moisture content
Adding wood Feeding Wood:
When new, the fireplace may emit a particular odour because the fireplace
is new. The odour will disappear completely after several fires.
Fresh wood is about 50 per cent water. The wood must always be dried so
that the moisture content is below 20%. If wood with a higher moisture
content is lit, a large part of the energy content of the wood is used for
boiling off the water. If the wood is damp, the combustion is also poor,
layers of soot and tar build up in the chimney and could, at worst, lead to a
chimney fire. In addition, it causes the glass of the stove to soot and may
cause discomfort to those living nearby.
To ensure thoroughly dry wood, the wood should be cut in the winter and
stored, well aired, under a roof. Never cover the woodpile with a tarpaulin
to the ground. The tarpaulin will then act as a sealed cover and the wood
will be prevented from drying. Always store a small amount of wood indoors
for several days before use, so that the surface moisture has time to
evaporate.
Split logs
Length: 25-50 cm
Diameter: 7 - 9 cm
Normal weight: 2.1 kg/hour (2 pieces)
Max amount: 2.7 kg/hour (max 3 pieces per insertion.)
1. Open the door a few centimetres and allow the vacuum in the firebox to
equalise for a few seconds before opening the door fully.
2. Add 2-3 logs of a combined weight of approx 1.6-1.8 kg. Lay the logs
diagonally on each other so that the flame can take easily. Then close
the hatch.
3. The combustion damper must be completely open for 3-5 minutes or
until the logs turn black and catch fire. If slower combustion is then
required, the supply of combustion air can be reduced. The conditions
for controlling combustion vary depending on the temperature in the
firebox and the draft in the chimney.
4. An average energy output of 7 kW is achieved when the combustion air
damper is 50% open and 2 logs weighing about 1.6-1.8 kg are burning.
5. The lowest output of 4-5 kW is obtained when the combustion air
damper is 30% open. In this operating position, it is very important that
the combustion air damper is fully open for the first 3-5 minutes so that
the wood has time to burn properly before the supply of combustion
air is reduced. In order to maintain good combustion the combustion
air damper must never be closed to less than 30% open. A condition for
regulating the output is a thick bed of embers and high temperature in
the firebox. When the fire has died down to embers more wood should
be added.
Choosing fuel
It is important that the wood catches fire quickly. Quick lighting is
achieved by opening the combustion air damper fully for a moment.
Smoulder combustion produces a lot of smoke and, in the worst
instance, can cause quick gas ignition resulting in firebox damage.
IMPORTANT!

GB
24
Lighting Instructions
1
3
2
2
1
The door can be held in the open position using the push button on the
underside of the fireplace.
Installation of the door
!
Do NOT burn the following
Under no circumstances may fossil fuels, pressure impregnated wood,
painted or glued wood, chipboard, plastic or colour brochures be used as
fuel. All these materials can create substances that are damaging both
to the environment and the fireplace. Also avoid using extremely finely
chopped wood except for lighting, because it burns uncontrollably. Fuel of
this type causes flashover resulting in too high output.
Candles
Do not use old candle stubs as fuel. Melted wax runs down into the stove's
damper system and makes the stove unusable. Repairs for this are very
expensive.
The glass may become sooty with use, even if the fireplace is lit with
dry wood with a moisture content of 15 – 20%. Regular cleaning with
dry paper is usually sufficient to keep it clean. If the soot has been on
the glass for a prolonged period, use a cleaning agent or a special soot
removal agent to remove it. Such agents can be purchased from regular
hardware stores or from your local stove dealer. Never use cleaning
agents that contain any abrasives, these can damage the glass.
When emptying the ash-pan, ensure that there are no glowing embers.
The ash must be stored in a fireproof container with a lid for at least one
week before being disposed of.
Also clean inside the area where the ash-pan is located, otherwise
spilled ash can prevent the ash-pan from being fully inserted.
The grate and other cast iron components in the firebox can be cleaned
using a wire brush.
From a combustion point of view it is important to check gaskets,
because worn gaskets hinder combustion when the stove/insert draws
“extra air”.
Painted parts of the fireplace can be cleaned using a damp cloth, with a
small amount of detergent, if necessary. Damage to painted parts, e.g.
small scratches, can be rectified with Contura touch-up paint. Contact
your dealer.
As there is a constant large flow of air through the fireplace, as cold
room air is drawn in and hot air released, dust can collect behind and
under the fireplace. Therefore, these areas should be regularly cleaned.
Parts located near the actual seat of the fire may require replacing.
Examples of such parts are the firebox panels and grate. The service life
of these parts depends on how much and how the fireplace is used.
FIREBOX MAINTENANCE

GB
25
Lighting Instructions
Abnormal amounts of soot form on the glass
There is always a certain amount of soot on the glass and this is added to
with each lighting. Soot on the glass is caused by three things:
• The wood is damp, which causes poor combustion and generates a lot of
smoke as a result.
• Too low temperature in the firebox, which causes incomplete combustion
and poor draft in the chimney.
• The start-up fire is not made according to the instructions.
There is poor draft in the fireplace after new
installation
• Check the dimensions of the chimney so that they correspond to the
ones stated in the installation instructions.
• Check that there is nothing in the chimney to restrict the smoke and
that no nearby buildings or trees affect the wind around the chimney.
Possible causes of malfunctions and
how to rectify them
It is difficult to light the fire and the fire dies after a
short time
• Check that the wood is sufficiently dry.
• Too great a negative pressure in the house, for example when using a
kitchen extractor fan or other mechanical ventilation. Open a window
near the firebox before lighting the fire. Also try lighting some
newspaper and holding it up inside the firebox to get the draft going.
• The supply air duct from outdoors may be partially or totally blocked.
Remove the hose and try test lighting with combustion air from the
room.
• Check that the combustion air damper is open.
• The smoke outlet of the stove may be blocked with soot, which can occur
after sweeping. Lift the smoke baffle out and check.
• Finally, go through the lighting instructions again. Perhaps the amount
of kindling was too small and therefore the base embers were too weak
and cold to light the next load of wood.
Smoke odour around the firebox at times
This can occur when wind blows down the chimney and most often occurs
when the wind is from a particular direction. Another reason could be that
the door was opened when there was a lot of flame.
Painted parts have become discoloured
If painted parts have discoloured it is due to excessive temperature in
the firebox. The reason for the excessive temperature could be that the
maximum amount of wood has been used or that inappropriate fuel has
been used (for example building waste, large quantities of finely chopped
off cuts). The warranty does not cover damage of this type. If a problem
occurs that you cannot rectify yourself, contact the dealer or a chimney
sweep.
We hope that these lighting tips give you enjoyable, economical and
problem free use of your Contura fireplace.

GB
26
Lighting Instructions
!
SWEEPING
Sweeping the chimney ducts and chimney connections
should be carried out by a chimney sweep. Sweep the stove
by scraping and/or brushing. A soot vacuum cleaner is
most appropriate however. If a chimney fire occurs or is
suspected, the combustion damper and the door must be
closed. If necessary, contact the fire brigade to extinguish
it. The chimney must always be inspected by a chimney
sweep after a chimney fire.
• During operation, the surfaces of the fireplace become very
hot and can cause burn injury if touched.
• Also, take heed of the strong heat radiated through the door
glass.
• Placing flammable material closer than the safe distance
indicated may cause a fire.
• Smoulder combustion can cause quick gas ignition with the
risk of damage to property and personal injury.
• The ash-pan must be emptied when it is full. If this is not
done, the air supply can become blocked, resulting in poor
function. In serious cases, ash can find its way out through
the damper.
The stove packaging is cardboard, wood and a
small amount of plastic. The materials must be
sorted and recycled.
Managing waste
Hearth plate glass must
be discarded as waste
material together with
pottery and porcelain
Contura reserves the right to change dimensions
and procedures described in these instructions
at any time without special notice. The current
edition can be downloaded from www.contura.eu
NIBE AB Box 134 SE-285 23 Markaryd Sweden
www.contura.eu

Contura reserves the right to change dimensions
and procedures described in these instructions
at any time without special notice. The current
edition can be downloaded from www.contura.eu
NIBE AB Box 134 SE-285 23 Markaryd Sweden
www.contura.eu
811306 BAV SE-EX Ci7_C300-2
2017-04-19