Nikon ED 17-55mm f/2.8G IF Operating instructions

JAA78851-R.3617.A
作成承認印 配布許可印
NIKON CORPORATION
Tokyo, Japan
Recycled paper
Printed in Japan March 2004
Copyright ｃ 2004 by Nikon Corporation.
All Rights Reserved.
REPAIR MANUAL
AF-S DX Zoom-Nikkor
ED 17-55mm f/2.8G IF
JAA78851
INC

JAA78851-R.3617.A
- M1 ･AF-S DX17-55/2.8G -
SPECIFICATIONS
Type of lens
Focal length
Maximum aperture
Lens construction
Picture angle
Focal length scale
Distance information
Zoom control
Focusing
Shooting distance scale
Closest focus distance
Diaphragm
Aperture range
Exposure measurement
Attachment size
Dimensions
Weight
G-type AF Zoom- Nikkor lens having built-in CPU and Nikon F bayonet mount
17mm - 55mm (22.5 - 82.5 mm in 35 mm format)
f/2.8
14 elements in 10 groups (3 aspherical lens and 3 ED lens elements)
79 ° - 28 ° 50' (with Nikon Digital Camera D1/D1H/D1X/D100)
17,20,24,28,35,45,55mm
Output to camera body
Manually via separate zoom ring
Nikon Internal Focusing (IF) system (utilizing an internal Silent Wave Motor);
manually via separate focus ring
Graduated in meters and feet from 0.36m (1.25ft.) to innity (∞)
0.36m (1.2ft.) at all zoom settings
Fully automatic
f/2.8-f/22 at all zoom settings
Via full-aperture method with cameras having CPU interface system
77mm (P=0.75mm)
Approx. 85.5mm dia. ×110.5mm extension from the camera's lens mount ange
Approx.755g
This lens can be used for Nikon digital SLR camera only.
INC

JAA78851-R.3617.A
- L1・AF-S DX17-55/2.8G -
※ Before Disassembly / (Re)assembly / Adjustment
If the 1st lens group and 4th lens group of this lens are removed, lens alignment
becomes necessary after assmbling.
Therefore, at service agencies where the lens alignment cannot be performed,
remove neither the 1st lens group nor 4th lens group.
INC

JAA78851-R.3617.A
- L2・AF-S DX17-55/2.8G -
DISASSEMBLY
#50×6
Filter ring
#137
1st lens group
#49×3
#77
Note: If the 1st lens group is removed,
lens alignment of the 1st lens
group becomes necessary.
Therefore, at service facilities
where the point tester is not
prepared, do NOT disassemble.
1ST LENS GROUP
FILTER RING
INC

JAA78851-R.3617.A
- L3・AF-S DX17-55/2.8G -
#38
B8 B11
#63×3
2ND LENS GROUP
2nd lens group
・Set the focus ring to the close-end, and the zoom ring to slightly 35-mm side from 28 mm.
・Assemble J11303B into the cam ring to seat in notches of the cam ring, then insert the pin
(J11303C) into the hole of J11303B. （ref. Fig.1）
・Remove the 2nd lens group with the wrench for 2G AF-S 17-35DX (J11303A). (ref. Fig.2)
Fig.1
J11303B
J11303C J11303A
Fig.2
INC

JAA78851-R.3617.A
- L4・AF-S DX17-55/2.8G -
REAR COVER RING
Rear cover ring
#182×3
#172×4
#78
#180×2
BAYONET MOUNT
INC

JAA78851-R.3617.A
- L5・AF-S DX17-55/2.8G -
4TH LENS GROUP
#71×3
#47
4th lens group
INDEX RING
#128×3
Index ring
Note: If the 4th lens group is removed,
the lens alignment becomes
necessary. Therefore, at service
facilities where the lens alignment
equipment is not prepared, do not
disassemble.
INC

JAA78851-R.3617.A
- L6・AF-S DX17-55/2.8G -
ZOOM ENCODER BRUSH
・Set the zoom ring to 17 mm, and take out 2 screws (#96). (ref. Fig.1)
・Set the zoom ring to 28 mm, and remove the zoom encoder brush. （ref. Fig.2)
#96×2 Zoom encoder brush
Fig.1
ZOOM CONNECTING PLATE
#184×2
#59
Cam ring
・Set the zoom ring to WIDE-end.
・Take out 2 screws (#184) to remove the
zoom connecting plate.
Zoom encoder brush
Fig.2
INC

JAA78851-R.3617.A
- L7・AF-S DX17-55/2.8G -
#115×4
・Take out 4 screws (#115) to remove the
zoom ring unit.
・Pass the switch part of M/A selector
switch through the hole of the zoom
ring unit.
・Remove the washer (#169).
#188×2
#169
M/A selector switch
ZOOM RING
#67×2
Zoom ring rubber
Zoom ring
Rear xed tube
Notch
Protrusion
#131
Zoom ring unit
・Take out the screw (#131).
・Align the notch of the zoom ring with
the protrusion of the rear xed tube, and
remove the zoom ring from the rear xed
tube.
INC

JAA78851-R.3617.A
- L8・AF-S DX17-55/2.8G -
AF CONTACT UNIT
AF contact unit
・Remove the AF contact unit from
the connector A of the main PCB.
#200
・Peel off the light-shielding sheet
(#200).
LIGHT-SHIELDING SHEET
Tape
・Remove the tape of the main PCB.
M/A SELECTOR SWITCH
A
INC