Nikon AF-S DX Nikkor 18-55mm/F3.5-5.6G VR Operating instructions

作成承認印 配布許可印
JAA80351-R.3739.A
JAA80351
Copyright ｃ2007 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
Printed in Japan November 2007
AF-S DX Nikkor
18-55mm/F3.5-5.6G VR
REPAIR MANUAL
Ｍ
サービス
計画課
INC

JAA80351-R.3739.A
- 󲦑・AF-S DX 8-55/3.5-5.6G VR -
Caution:
When disassembling/(re)assembling, be sure to use the conductive mat (J5033) and wrist strap
(J5033-5) for static protection of electrical parts.
When disassembling, make sure to memorize the processing state of wires, screws to be xed and
their types, etc.
Because prototypes are used for "1. Disassembly" and "2. Assembly/Adjustment", they may differ
from the actual products in forms, etc.
Because pictures are processed by a special method, they may differ from the actual ones in texture.
�
�
�
�
This lens will require optical lens alignment after assembly, in case the 4th lens-group unit is removed.
At repair service facilities, therefore, where this alignment work can not be performed, do NOT remove the
4th lens-group unit.
This lens also has the VR (vibration-reduction) unit mounted in order to correct camera shake.
To keep the accuracy of this function for stabilizing the image, in case the gyro FPC, main PCB, or thethe
            
equipment (J15380). 

disassemble NOR repair the products of the above cases.
・Lead-free solder is used for this product.
・For soldering work, the special solder and soldering iron are required.
・
・Use the special soldering iron respectively for lead-free solder and lead solder.
They cannot be used in common.
Points to notice for Lead-free solder products
※Before Disassembly / Reassembly / Adjustment
INC

JAA80351-R.3739.A
- 󲦑・AF-S DX 8-55/3.5-5.6G VR -
・Remove the company name ring (#113).
#113
・Remove the name plate (#68) and VR name plate (#69).
#69 #68

replaced.
1.Disassembly
Company name ring
Name plate/VR name plate
INC

JAA80351-R.3739.A
- 󲦑3・AF-S DX 8-55/3.5-5.6G VR -
・Remove the rubber ring (#62) by pulling towards the 1st lens group side.
#62
#91
#39
#91
#91
Rubber ring
・Take out the three screws (#91) and remove the rear cover ring (#39).
Rear cover ring
INC

JAA80351-R.3739.A
- 󲦑・AF-S DX 8-55/3.5-5.6G VR -
・Set the zoom to WIDE-end or TELE-end.
・Turn the 1st lens-G unit (B40) counterclockwise. Then remove the washer (#119: selected from A to I) and
the 1st lens-G unit (B40).
#38
B40
#119A ～I
1st lens group unit
INC

JAA80351-R.3739.A
- 󲦑5・AF-S DX 8-55/3.5-5.6G VR -
・Set the zoom to WIDE side.
・Take out the three screws (#143) and remove the three washers (#177). Then remove the 4th lens-G unit
(B46).
4th lens group unit
B46
#143×3
#177×3
Caution: The lens alignment work will be necessary after assembly, in case the 4th lens-G unit is removed.
At repair service facilities, therefore, where such alignment work can not be performed, do NOT
remove the 4th lens-G unit.
Zoom front ring unit
・Peel off the polyester tape (#77).
#77
INC

JAA80351-R.3739.A
- 󲦑6・AF-S DX 8-55/3.5-5.6G VR -
B54
・Remove the zoom front ring (#54).
・Set the M/A switch to "A" side, and take out the screw (#155).
B1013
#155
B152
B152
Change-SW unit
・Lift the black part of the connector of the PI-FPC (B1013), and remove the FPC of the change-SW unit
(B152).
INC

JAA80351-R.3739.A
- 󲦑・AF-S DX 18-55/3.5-5.6G VR -
・Remove the GND lead wire (#1027) from the PI-FPC (B1013).
B1013
#1027
GND lead wire
・Take out the three screws (#78), and remove the bayonet mount unit (B30).
B30
#78×3
Bayonet mount unit
・Take out the two screws (#67).
#67 #67
B1006
△（Addition）
△（Addition）
Changed page △× 2 December．10．200
Ｍ
サービス
計画課
INC

JAA80351-R.3739.A
- 󲦑8・AF-S DX 8-55/3.5-5.6G VR -
・Remove the washer (#101: selected from A to I).
#101A - I

・
B57
INC

JAA80351-R.3739.A
- 󲦑・AF-S DX 8-55/3.5-5.6G VR -
・Remove each FPC from the main PCB (B1001).
Main PCB unit
Zoom-FPC (#1007)
Focus-FPC (#1014) Hall element-FPC (B1005)
PI-FPC (B1013)
Gyro-FPC (B1004) Main VCM-FPC (#1009)
#179
SWM-FPC
・Remove the FPC of the contact pin unit (B1006) from the main PCB (B1001).
B1001
B1006
Contact pin unit
・
INC