Ninja BL810 User manual

Ultima™Dual Stage Blender
OWNER’S GUIDE
BL810 series
®
www.sharkninjamanuals.com
®
HELP
LINE
1 877 646-5288

1TOLL FREE: 1-877-646-5288
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL
APPLIANCES, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR NINJA ULTIMA™DUAL
STAGE BLENDER.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. To protect against electrical shock, do
not submerge the appliance or allow the
power cord to come into contact with
water or any other liquid.
2. DO NOT allow young children to
operate the appliance or use as a toy.
Close supervision is necessary when any
appliance is used near children.
3. Never leave an appliance unattended
when in use.
4. Turn the appliance off and remove the
power cord from the electrical outlet
when not in use, before assembling or
disassembling parts, accessing parts that
move while in use and before cleaning.
To unplug, grasp the plug and pull from
the electrical outlet. Never pull from the
power cord.
5. DO NOT abuse the power cord. Never
carry the appliance by the power cord
or yank it to disconnect from electrical
outlet; instead grasp the plug and pull to
disconnect.
6. DO NOT use with damaged cord or plug.
7. DO NOT USE if the appliance is not
working, has been dropped, dropped
into water, damaged or left outdoors.
8. NO SERVICEABLE PARTS. Incorrect
re-assembly or repair can cause a risk of
electrical shock or injury to persons when
the appliance is used. Contact Customer
Service.
9. DO NOT let the power cord hang over
the edge of table or counter or touch hot
surfaces such as the stove.
10. Always use the appliance on a dry, level
surface.
IMPORTANT:
This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children shall not use or play with this
appliance. Close supervision is necessary
to keep appliance out of reach of
children during use.
WARNING:
The blades are not affixed to the
unit. They are removable and very
sharp. Handle with care!
CAUTION: In order to avoid a
hazard due to inadvertent resetting of
the thermal cut-out, this appliance must
not be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.

2
www.sharkninjamanuals.com
SAVE THESE
INSTRUCTIONS
23. DO NOT expose containers to extreme
temperature changes.
24. CAUTION: DO NOT process hot foods
or hot liquids. Allow hot ingredients to
cool before processing.
25. DO NOT overfill. DO NOT exceed max
fill line.
26. DO NOT operate the appliance empty.
27. To reduce the risk of burns, always allow
the appliance to cool before taking off
parts and before cleaning.
28. Max ON time is 30 seconds under
1500W load. If the appliance overheats,
a thermal switch will become activated
and shut off the motor. To reset, unplug
the appliance and let it cool down for
approximately 15 minutes before using
again.
29. In the event that the unit overloads, the
control panel lights will flash and the unit
will shut down. Unplug the unit and wait
15 minutes to reset.
30. The maximum rating is based without
the top blades inserted into the pitcher.
This drives the greatest power. Other
recommended attachments may draw
significantly less power or current.
31. To avoid injury, never attempt to place
the single serve blade assembly onto the
motor base without first assembling the
blade assembly to the single serve cup.
32. THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY. Do not use
this appliance for anything other than its
intended use. Do not use outdoors.
WARNING: Extension cords are
not recommended for use with this product.
11. Keep hands, hair, clothing, as well as
utensils out of container while processing
or blending to reduce the risk of severe
injury to persons or damage to the
appliance. A scraper may be used but
only when the appliance is not running.
12. CAUTION: The top blades are not
affixed to the pitcher, they are removable
and extremely sharp. When handling the
top blades do not hold blades, but rather
always hold by the shaft. Blades are
sharp. Handle carefully!
13. Avoid contact with moving parts.
14. DO NOT attempt to sharpen blades.
15. DO NOT use the appliance if either set of
blades are bent or damaged.
16. To reduce the risk of injury, never
assemble the top blades in the pitcher
without the pitcher properly attached to
the motor base.
17. DO NOT operate this appliance on or
near any hot surfaces (such as gas or
electric burner or in a heated oven).
18. The use of attachments or accessories
including canning jars, not recommended
by the manufacturer, may result in fire,
electric shock or personal injury.
19. DO NOT remove the container from
the motor base while the appliance is in
operation. Always unplug the unit when
not in use.
20. To reduce the risk of injury, NEVER
operate the appliance without the lid in
place; DO NOT try to defeat or bypass
the interlock mechanism. When using the
top blades, make sure they are properly
installed before operating the appliance.
21. CAUTION: DO NOT BLEND HOT LIQUIDS.
22. Extreme caution must be used when
moving an appliance containing hot food,
water or other liquids.

3TOLL FREE: 1-877-646-5288
THIS BOOK COVERS MODEL NUMBERS:
BL810***** 30
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz.
Power: 1500 Watts
Max ON time is 30 seconds under 1500W load
Pitcher Capacity: 2.1 Litres
Max. liquid 1.8 Litres
Single Serve Capacity: 470 ml
Euro-Pro, Ninja, Sip & Seal, Ultima and Ninja Ultima are
trademarks of Euro-Pro Operating LLC.
This applaince complies with the WEEE-Directive 2002/96/EC on the disposal of
electrical and electronic equipment (WEEE).
This appliance complies with the European directives for electromagnetic
compatibility (EMC) 2004/108/EC and its revisions, as well as Low Voltage Directive
(LVD) 2006/95/EC and its revisions.
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health fom uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact the
retailer where this product was purchased. They can take this product for
environmental safe recycling.

4
www.sharkninjamanuals.com
Contents
Thank you for
purchasing the
Ninja Ultima™
Dual Stage
Blender.
Getting to Know Your Ninja Ultima™Dual Stage Blender........................ 5
Using the Ninja Ultima™Dual Stage Blender .........................................7
Assembly and Use for the 2.1 L Pitcher................................................... 8
Assembly and Use for the Single Serve Cup ........................................... 10
Usage, Blade Selection & Speed Settings................................................11
Care & Maintenance ............................................................................... 12
Troubleshooting Guide............................................................................ 13
Warranty & Registration.......................................................................... 14

5TOLL FREE: 1-877-646-5288
Getting To Know Your Ninja Ultima™Dual Stage Blender
a
d
e
b
cf
g
h
i
fSingle Serve Drink Cup (x2) (355KKU800IN)
gSingle Serve Blade (357KKU800)
hMotor Base (358KKU810)
iControl Panel
jPower Cord (not shown)
aPitcher Lid with Locking Handle (352KKU800)
bTop Blades (Removable) (353KKU800)
cPitcher
(351KKU800IN)
dBottom Blades (Fixed)
eSip & Seal™ To-Go Lids (x2) (356KKU800)

6
www.sharkninjamanuals.com
The Ninja Ultima™Dual Stage Blender features a dual blade system and 2.5 peak horsepower
motor for culinary precision at home. For best results, be sure to carefully read all the instructions
contained in the manual before using this appliance.
FEATURES:
• Ninja Dual Stage Technology
• Extra Large 2.1 L Pitcher and Single Serve Drink Cups - BPA Free
• Drip-Free Pour Spout
• Sip & Seal™ To-Go Lids
• Easy to Clean Control Panel
• Sturdy, Non-Slip Base
• Hidden Drain Holes - prevent water build up from dishwasher
• Dual-blade system
• Lid featuring Smart Lid technology for easy release

7TOLL FREE: 1-877-646-5288
Using the Ninja Ultima™Dual Stage Blender
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING
THE APPLIANCE:
IMPORTANT: When using the top blades,
always add the ingredients into the
blender AFTER inserting the top blades.
CAUTION: Blades are sharp! Use extreme
caution when handling the top blades.
Always hold them by the shaft.
IMPORTANT: DO NOT attempt to
operate the appliance without the lid on.
IMPORTANT: Never run the appliance
empty.
CAUTION: DO NOT process food or
liquids that are hot. Allow hot ingredients
to cool before processing.
WARNING: Secure the appliance while in
use by pressing down on the lid with one
hand.
CAUTION: Never remove either container
or try to remove the lid from the pitcher
while the appliance is still running.
WARNING: Never leave the appliance
unattended while in use.
BEFORE FIRST USE
1Remove all packaging material and labels
from the appliance.
2Wash the lids, pitcher, single serve cups and
top blades in warm, soapy water with a soft
cloth. Use caution when washing the
removable top blades as the blades are
very sharp. Rinse and dry thoroughly.
OR
3All accessories are dishwasher safe except
the motor base. When using the dishwasher,
place the pitcher and single serve cups in the
dishwasher. Place the lids and attachments
on the top rack. Use caution when washing
the removable top blades as the blades
are very sharp. Always hold the top blades
from the shaft.
4Wipe the motor base clean with a damp cloth.
Do not submerge the motor base in water or
any other liquid.

8
www.sharkninjamanuals.com
Fig. 3b
Fig. 2
Fig. 1
Assembly and Use for the 2.1 L Pitcher
IMPORTANT: Make sure that the motor
base is plugged in for use.
1Place the motor base on a clean, dry, level
surface such as a counter or table top.
2Align and lower the pitcher onto the motor
base. (Fig. 1) Handle should be aligned
slightly to the right of the “LOCK” symbol on
the motor base.
3Rotate the pitcher clockwise as far as it will
go to lock in place. (Fig. 2)
NOTE: The pitcher can be placed on the motor
base two ways; the handle can be on the front
right corner or the front left corner. (Fig. 3a,
Fig. 3b)
4Holding the top blades by the top of the shaft,
place it onto the bottom blades inside the
pitcher. Ensure that the top blades are seated
properly by standing upright in the pitcher. Do
not operate the unit if the top blades are not
upright at any time. (Fig. 4)
NOTE: The top blades will fit loosely on the
bottom blades but will be secured once the lid
is in place.
TIP: When pureeing, use only the bottom
blades for best results.
NOTE: The bottom blades are not removable.
5When using the top blades, ensure blades are
properly in place prior to adding ingredients.
Add the ingredients to the pitcher, making
sure that they do not exceed the 2.1 L mark on
the pitcher.
NOTE: When blending any kind of liquids,
such as mixtures of any drinks or smoothies,
do not exceed the “MAX LIQUID” mark (1.8 L)
on the pitcher.
NOTE: If you need to add additional
ingredients while the appliance is processing,
do not remove the lid. Open the pour spout
cap and add any additional ingredients, close
cap when complete.
6Holding the lid by the handle in the upright
position, place it on top of the pitcher aligning
the arrow ( ) located on the lid with the
arrow ( ) located on the pitcher’s handle.
(Fig. 5) Press the handle down until you hear
a click.
Fig. 4
Fig. 5
Assembly
Fig. 3a

9TOLL FREE: 1-877-646-5288
CAUTION: Never insert your hands in the
pitcher as the blades are sharp. Always use a
spatula to dislodge food that has stuck to the
sides of the pitcher. Unplug the unit before
attempting to dislodge anything.
12 Make sure that the unit is unplugged when
not in use.
TIPS:
• Use low speed settings (1-3) when blending
drinks and other blended items.
• Use medium speed settings (4-6) when
frozen blending, ice crushing or grinding dry
ingredients.
• Use high speed settings (7-10) when
creating purees such as sauces, dips and
restaurant quality glazes. Top blades are
needed to power through tough ingredients
like ice, solid fruits and vegetables. If silky
smooth results are desired, push down on
the power toggle to turn off the power,
carefully remove the top blades, replace the
lid and continue processing.
• For softer ingredients, the bottom fixed
blades are enough to fully process in one
step.
7Plug the motor base in for use.
8Turn the Variable Speed Dial to speed 1.
(Fig. 6) The power indicator light () will now
turn on.
To start the blender, press the “Start/Stop/
Pulse” toggle up to start processing. Slowly
increase to desired speed.
NOTE: As a safety feature, the power
indicator light ( ) will flash and the
motor will not work if the pitcher and lid
are not installed correctly.
NOTE: If you need to Pulse ingredients press
down on the toggle in short intervals.
9When you have reached your desired
consistency, reduce speed slowly and stop the
unit by pressing up on the Start/Stop/Pulse
toggle. (Fig. 7)
10 Use the convenient pour spout when serving
smoothies, juices and other beverages you
have created! Push the pour spout back as
far as it will go before pouring. For thicker
consistencies, remove the lid and the top
blades carefully (by the shaft), then empty the
contents from the pitcher.
11 To remove the lid, press the release button on
the lid, pull the lid handle up to a 90° angle
and lift the lid off. Holding the pitcher with
one hand while removing the lid with the
other will provide the best leverage. Turn the
pitcher counter clockwise and then lift off the
base. Do not pour out ingredients without
first carefully removing the top blades.
(Fig. 8)
Assembly and Use for the 2.1 L Pitcher - cont.
Fig. 7
USE REMOVAL
Fig. 6 Fig. 8
WARNING: Never leave the appliance unattended while in use.

10
www.sharkninjamanuals.com
IMPORTANT: Make sure that the motor
base is plugged in for use.
1Place the motor base on a clean, dry, level
surface such as a counter or table top.
2Add ingredients to the single serve cup.
NOTE: Do not overfill! To avoid spilling, do
not add ingredients past the “MAX FILL” line.
3Place the single serve blade onto the cup and
screw it on tightly until you have a good seal.
(Fig. 9)
4Turn the single serve cup upside down and
place it onto the motor base, aligning the tabs
on the cup with the motor base. (Fig. 10)
Turn clockwise until the cup locks in place,
the unit is ready for use. (Fig. 11)
5Turn the Variable Speed Dial to the Single
Serve icon. The single serve cup only operates
at one speed regardless of which number is
chosen on the dial. Press down on the “Start/
Stop/Pulse” toggle in short intervals until you
have reached your desired consistency.
(Fig. 11)
Fig. 9 Fig. 10
Assembly and Use for the Single Serve Cup
Fig. 11 Fig. 12 Fig. 13
ASSEMBLY PULSE REMOVAL
For best results, use short “PULSES”... Practice makes perfect!!
6When you have reached your desired
consistency, turn the single serve cup counter-
clockwise (Fig.12) and pull straight up to
remove. (Fig. 13)
7Turn the cup upright and remove the single
serve blade by twisting the blade assembly
counter clockwise.
8Place the Sip & Seal™To-Go drinking lid onto
the single serve drink cup, screw on to seal
and enjoy!
9Make sure that the motor base is unplugged
when not in use.

11 TOLL FREE: 1-877-646-5288
Usage, Blade Selection & Speed Settings
• Top blades are needed to power through tough ingredients like ice, solid fruits and
vegetables. If silky smooth results are desired, carefully remove the top blades and continue
processing.
• For softer ingredients, the bottom fixed blades are enough to fully process in one step.
• Use the single serve cup for great results when making individual portions of smoothies or
other drinks.
• The single serve cup is also great for chopping and creating salad dressings!
• The single serve cup only operates at one speed regardless of which number is chosen
on the dial. Press down on the “Start/Stop/Pulse” toggle in short intervals until you have
reached your desired consistency.
*TIPS:
Function Type of Food Suggested Blade(s) Speed Settings
Juices / Smoothies Fruits
Vegetables Top blades & bottom blades Pulse then 5 - 10
Ice Crushing /
Frozen Blending
Ice
Frozen fruit
Ice cream
Top blades & bottom blades Pulse then 5 - 10
Pureeing
Smooth soups
Milkshakes
Nut milks
Top blades & bottom blades*
Bottom blades only* 1 - 10
Emulsifying Salad dressings
Sauces Bottom blades only 1 - 5
Chopping
Salsa
Vegetables
Nuts
Top blades & bottom blades Pulse
Mixing Batters
Dips Bottom blades only 1 - 3
Grinding Meat Top blades & bottom blades Pulse
Nut Butters
Sunflower butter
Peanut butter
Almond butter
Top blades & bottom blades 1 - 8
Milling
Flours
Rice
Quinoa
Chick Peas
Top blades & bottom blades 5 - 8

12
www.sharkninjamanuals.com
Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base
is unplugged from the power source before
inserting or removing any attachment and
before cleaning.
CAUTION: DO NOT immerse the motor base
into water or any other liquid.
1Separate/remove all parts from each other.
2Clean the motor base with a damp cloth and
wipe dry.
3Place the pitcher and single serve cup in the
dishwasher. Place the lids and attachments on
the top rack. Use caution when handling
the blade assemblies as the blades are
very sharp. Always hold the top blades
from the shaft.
NOTE: You may also wash the containers by
filling ¾ of the container with warm water
and a drop of dish washing detergent, placing
the lid or single serve blade assembly on and
pressing the pulse button a few times. Once
clean, remove the container from the motor
base. Rinse the pitcher, single serve cup and
lids under running water. Allow all the parts
to dry before storing.
HOW TO STORE
1Store the Ninja Ultima™Dual Stage Blender
upright with the pitcher on the motor base,
top blades inside the pitcher and lid on the
pitcher.
RESETTING THE MOTOR THERMOSTAT
The Ninja Ultima™Dual Stage Blender
features a unique safety system which
prevents damage to the unit’s motor and
drive system should you inadvertently
overload your appliance. If the appliance is
being overloaded, the motor will stop and
the power indicator light will flash. To reset
the appliance, follow the resetting procedure
below:
1Unplug the appliance from the electrical
outlet.
2If using the top blades, carefully remove them
by the shaft, ensuring that no food is jamming
the top or bottom cutting blades.
CAUTION: The blades are extremely sharp
- handle with care! Always hold the top
blades from the shaft.
3Allow the appliance to cool for approximately
15 minutes.
4Re-install the container onto the base,
carefully re-insert the top blades (if using) and
re-plug the appliance into the electrical outlet.
NOTE: Ensure that the top blades are seated
properly by standing the blades upright in the
pitcher. If the top blade is not seated properly,
carefully check the underside of the top blade
assembly to ensure there’s no food in the way.
Rinse if necessary. Do not operate if the top
blades are not upright at any time.
5Proceed to use the appliance as before,
making sure not to exceed the recommended
maximum capacities.

13 TOLL FREE: 1-877-646-5288
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor doesn’t start or
attachment doesn’t rotate.
Make sure the pitcher or single serve cup is securely placed on motor base.
Make sure the lid is securely on pitcher in the correct position (align
arrows).
The appliance is unplugged. Plug the unit in, turn the Variable Speed Dial
to the desired speed setting and press the Start toggle up to turn “On”.
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power indicator
light will flash. Unplug and wait approximately 15 minutes before using
again.
The unit has overheated. Unplug and wait approximately 15 minutes
before using again.
Food is unevenly chopped.
You are chopping too much food at one time. Try processing smaller
amounts per batch.
Food is chopped too fine or is
too watery.
The food has been over processed. Use short pulses for best results.
Food collects on lid or on the
sides of the container.
The mixture is too thick. Add more liquid.
You cannot achieve snow
from solid ice.
Do not use ice that has been sitting out or has started to melt. Use ice
straight from the freezer. Pulse for best results.
Variable speed won’t work
on my single serve cup.
The single serve cup only operates at one speed regardless of which number
is chosen on the dial. Press down on the “Start/Stop/Pulse” toggle in short
intervals until you have reached your desired consistency.
Troubleshooting Guide

14
www.sharkninjamanuals.com
**THIS WARRANTY IS FOR ALL COUNTRIES EXCEPT GERMANY**
Product Registration
Please visit www.sharkninjamanuals.com or call 1-877-646-5288 to register your new Ninja®
product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and
model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By
registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for
a period of one (1) year from the date of purchase when utilized for normal household use, subject to the
following conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the
unit at our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit
that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage
caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This
Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or
repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not
authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service
options or customer support, please call our customer care and product specialists at , call 1 [phone] or
visit our website www.sharkninjamanuals.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair
or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of
return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific
obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO
Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some
states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not
apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state
to state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with the item. We recommend you insure the package (as damage
in shipping is not covered by your Limited Warranty). Mark the outside of your package
“ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products,
therefore the specifications contained herein are subject to change without notice.

15 TOLL FREE: 1-877-646-5288
Product Registration
Please visit www.sharkninjamanuals.com or call 1-877-646-5288 to register your new Ninja®product
within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number
along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering
you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
TWO (2) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of
two (2) years from the date of purchase when utilised for normal household use, subject to the following conditions,
exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at
our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been
tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse,
abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited Warranty does
not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the
product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating
LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or
customer support, please call our customer care and product specialists at, call 1 [phone] or visit our website
www.sharkninjamanuals.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace
it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight.*
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific
obligations expressly assumed by it under the terms of this Limited Warranty.
In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any
nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so
the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state
or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your Limited Warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
**THIS WARRANTY IS FOR GERMANY ONLY**

16
www.sharkninjamanuals.com
Euro-Pro Operating LLC
180 Wells Avenue Suite 200, Newton MA 02459
United States of America
1-877-646-5288
www.sharkninjamanuals.com
Copyright © 2013 Euro-Pro Operating LLC
Euro-Pro, Ninja, Sip & Seal, Ultima and Ninja Ultima are
trademarks of Euro-Pro Operating LLC.
Printed in China
Illustrations may differ from actual product.
BL810*****series.30.E.131218.1