Nitek FTS324104R00 User manual

Installation Manual
FTS324104R00 Dual Transmitter
2 Camera Transmitter w/Data and Aux Comm.
Note: This installation should be made by a qualified
service person and conform with local codes.
Reduce risk of fire or electrical shock do
not expose this product to rain or moisture.
!
Specifications
Video Connection
Connector 75 ohm BNC Socket
Input Impedance 75 ohm terminated
Input Level 1 volt p-p nominal
Frequency Response 10Hz to 10MHz
Optical Connection
Connector SC Style
Path Loss 20 dB
Wavelength 1310 / 1550nm
Dimensions
Width 1 Card slot
Power Connection
Provided from FSR1000 Card Rack
Auxiliary Ports
Data Selectable RS422/RS485/RS232
Alarm In Contact Closure
Alarm Out Relay 100V / 150mA max
NITEK®
5410 Newport Drive, Suite 24
Rolling Meadows, IL 60008
PHONE [phone]
FAX [phone]
WWW.NITEK.NET
Installation Instructions
- The fiber transmitter is designed to be mounted in the FSR1000 Fiber Card Rack.
- Always allow for bend radius of optical and electrical cables when installed.
680600111 Rev 02102009
Service Information
There are no user serviceable parts inside the unit. In the event that service is required to this unit please
contact NITEK Technical Support at 800-528-4343.
CH1 CH2
NITEK
CH1
POWER
VIDEO/OPTO
CH2
DATA OUT
DATA IN
ALARM OUT
ALARM IN
CH1
CH2
OPTO IN / OUT
Color Description
Green Data is Low / Logic 0
Red Data is High / Logic 1 (RS422/485)
Off Data is Tri-state / (High - RS232)
Data LED
Color Description
Green System Normal
Yellow (RX) Link working, No video at TX
Red (TX) Power on, No video into TX
(RX) Power on, No opto into RX
Power/Video/Opto LED
Data CH1 RS485
RS422
RS232
Data RS485 RS422 RS232
IN + (A) 7 1 2
IN - (B) 8 2 --
OUT + (A) 7 7 8
OUT - (B) 8 8 --
GND 6 6 6
Rear Panel Data Connections
Set Data Format with Internal Switch
Alarm Connections
Alarm Pin
OUT + 3
OUT - 4
IN + 5
GND 6

Typical Installation - FTS324104R00
NITEK
CH1
POWER
VIDEO/OPTO
CH2
DATA OUT
DATA IN
ALARM OUT
ALARM IN
CH1
CH2
OPTO IN / OUT
CH1 CH2
BACK FRONT
Connect incoming
fiber using SC
connectors
VIDEO IN
DATA OUT
Data Connections
AUX COMM IN / OUT
DEPENDING ON SWITCH
SETTING
DATA / ALARM CH1
DATA / ALARM CH2
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Alarm Connections
Alarm Pin
OUT + 3
OUT - 4
IN + 5
GND 6
Data CH1 RS485
RS422
RS232
Data RS485 RS422 RS232
IN + (A) 7 1 2
IN - (B) 8 2 --
OUT + (A) 7 7 8
OUT - (B) 8 8 --
GND 6 6 6
Rear Panel Data Connections
Set Data Format with Internal Switch
Color Description
Green System Normal
Yellow (RX) Link working, No video at TX
Red (TX) Power on, No video into TX
(RX) Power on, No opto into RX
Power/Video/Opto LED
Color Description
Green Data is Low / Logic 0
Red Data is High / Logic 1 (RS422/485)
Off Data is Tri-state / (High - RS232)
Data LED