NOBLE CHEMICAL 158NOVAK59WH User manual

WHITE
FOAM SOAP/SANITIZER DISPENSER
#158NOVAK59WH
READ ENTIRE MANUAL BEFORE USE
Novo by Noble Chemical, Inc. • 2205 Old Philadelphia Pike • Lancaster, PA 17602
07/2020
INSTRUCTION
MANUAL

INSTRUCTION MANUAL  2
PART DIAGRAM
TOP VIEW
BOTTOM VIEW
SPECIFICATIONS
Top Cover
Swiveling Cover
Fluid Input
Body
Indicator
Outlet
Hex Key
Battery Box
Wall Mounting Panel
Opening Lock
Setting Button
Anti-theft Lock
Battery Box Cover
Anti-theft Screw
Sensor Window
Outlet
VOLTAGE DC6V/(4) AA Batteries
VOLUME 28.7 oz. (850mL)
AMBIENT TEMPERATURE 32°-113°F (0-45°C)
SUPPLY 5 Adjustable Levels: 0.01-0.08 oz. (0.5-2.5 mL)
SENSING DISTANCE 2-3.5 in. (5-9 cm)
MATERIAL ABS Plastic

INSTRUCTION MANUAL  3
IMPORTANT SAFETY INSTRUCTIONS
PACKING LIST
The following instructions must be followed to ensure optimal unit condition
and extended lifespan
• Instructions must be followed carefully while installing the unit.
• Always use new, identical batteries when installing unit.
• Ensure that mounting surface is flat and clean before installing.
• Ensure that the unit is installed at least 25 cm above the nearest surface to avoid sensing errors.
• Each unit is to be installed by a qualified professional.
• Do not install unit directly above reflective surfaces.
• This unit is intended for indoor use only.
• Children using the unit must be accompanied by an adult to avoid injury or malfunction
• Please ensure proper disposal of depleted batteries
• Keep unit dry at all times to avoid electrical malfunction
• This unit contains electrical devices and valves, handle with care.
• Disassemble unit with care to avoid damaging liquid feed line
• Only clean unit with neutral detergents, and dry with a soft cloth
• Do not clean unit with water or non-neutral detergents to avoid surface damage or internal
electrical failure. Only clean sensing area on underside of unit with a soft, dry cloth to avoid
sensing errors.
• Unit must be installed at least 14" above surfaces to avoid sensor malfunction.
TO REDUCE RISK OF INJURY OR UNIT MALFUNCTION,
OBSERVE THE FOLLOWING INSTRUCTIONS
• Ensure that all items below are included with our dispenser upon delivery.
If any parts are missing or damaged, contact your distributor.
• Item specifications are subject to change over time.
If there are any issues with installation, contact your distributor.
• The unit and main components are shipped sealed in bags. Open with care to avoid damages.
(1) Automatic Soap Dispenser
(1) Wall Mounting Panel
(3) Expansion Screws
(3) ST4x25 Screws
(1) Key
(1) User Manual
(1) Certificate of Qualification
WARNING
CAUTION

INSTRUCTION MANUAL  4
INSTALLATION
TIP: Ensure that unit is
mounted at least 14" (35
cm) above stainless steel or
other reflective countertop
surfaces.
>10" (25 cm)
7.9" (20 cm)
1. Place mounting bracket
where the unit will be secured
to the wall. Mark the locations
of the 3 holes.
2. Drill holes into the marked
areas of the mounting surface.
After holes are drilled, insert
expansion screw heads into
the corresponding holes.
3. Place mounting plate on
the wall, corresponding with
the expansion screw heads.
Then fasten mounting plate
with screws in corresponding
locations.
4. Line up grooves in back
of unit with the mounting
plate, and slide dispenser
into bracket until it locks
into place.
Upper Slot
Upper Hook
Nether Slot
Nether Hook
Hex Key

INSTRUCTION MANUAL  5
BATTERY INSTALLING & REPLACEMENT
HOW TO USE
1. Unscrew the security screw
and remove battery housing
from the unit.
2. Insert batteries into the
housing following the
indicated + and - symbols.
3. Insert battery housing back
into the unit, and tighten
security screw to secure.
1. Insert key into the lock on the top cover of the unit, and turn to remove.
2. Remove inner container cover and fill unit with foaming soap.
3. Unscrew the battery housing unit from the bottom of the dispenser, and insert 4 AA batteries
into the housing. Then insert housing back into the unit, and tighten screw to secure.
4. Hold the setting button on the bottom of the unit for 3 seconds, then an LED light will flash
3 times to indicate that the unit is in standby mode.
5. After the LED light flashes, soap will be dispensed when hands are moved into the sensing area.
The unit may require a few senses before dispensing to prime.
6. The LED light will flash 3 times in 30 seconds to indicate low battery power.
Replace batteries when this occurs.
1. Open top cover, add
soap or sanitizer and
remove any overflow.
2. Soap will dispense
automatically when hands
are moved under the
sensing area.
Battery
Cover
AA
Screw
CAUTION
WARNING
• The LED indicator light will flash 3 times when the batteries are low.
• This unit requires 4 AA batteries. Always use new, identical batteries when replacing.
• Children using the unit must be
accompanied by an adult to avoid
injury or malfunction.
• Please ensure proper disposal
of depleted batteries.
• Keep unit dry at all times to avoid
electrical malfunction.

INSTRUCTION MANUAL  6
DISPENSE QUANTITY ADJUSTMENT
TROUBLESHOOTING
• When the unit is powered on, press and hold the setting button for 3 seconds, until the LED indicator
light flashes 3 times. The LED light indicates that the unit is in standby mode.
• Adjustable foaming soap settings: This unit can be set to 5 dierent levels of foam soap supply per
dispense. The default amount of soap or sanitizer per dispense is .7 ml. After pressing the setting
button once, the amount will change to 1.0 ml. After additional consecutive presses, amount of soap or
sanitizer dispensed per sense is as follows: 1.3 ml, 1.6 ml, and 0.4 ml.
• TIP: Keep fluid container clean and free of dirt and dust to avoid blockages.
Problem Reason Potential Solution
LED INDICATOR OFF
Control System Trouble Replace the Controller
Power Supply Problem Check Circuits and Batteries
Batteries - Poor Contact or Out of Power Reinstall or Replace Batteries
Circuits - Problem or Poor Contact Check Circuits
Indicator Sight Blocked Clean the Indicator Window
LED LIGHT FLASH Not Enough Power Replace Batteries
INDICATOR ON WITHOUT
SOAP OR SANITIZER
SUPPLY
Sensor Continue Working Remove Sensing Object
Out of Sensing Distance
Place Hand Directly Below
Sensor, Slowly Move Side to Side
and Up and Down Until Soap
Dispenses
Unit Fault Contact the Dealer
INSUFFICIENT SOAP OR
SANITIZER SUPPLY
Short Soap or Sanitizer Supply Time Adjust Soap or Sanitizer Output
Soap or Sanitizer is Too Viscous Reduce Soap or Sanitizer
Viscosity
Soap or Sanitizer Coagulation or
Obstruction
Try Clearing Lines or Contact the
Dealer