NOBLE CHEMICAL Novo 158NOVAK55SS User manual

INSTRUCTION
MANUAL
STAINLESS STEEL
FOAM SOAP/SANITIZER DISPENSER
#158NOVAK55SS
READ ENTIRE MANUAL BEFORE USE
Novo by Noble Chemical, Inc. • 2205 Old Philadelphia Pike • Lancaster, PA 17602
07/2020

INSTRUCTION MANUAL  2
PART DIAGRAM
BOTTOM VIEW
DIMENSIONS
Key
Cap
Sealing Cap
Fixed Bracket
Battery Container
Indicator
Shell
Battery Container
8.67" (220mm)
3.93" (100mm) 4.33" (110mm)
Outlet
Sensor Window
Battery Container
Drain Outlet
Installation Panel

INSTRUCTION MANUAL  3
IMPORTANT SAFETY INSTRUCTIONS
PACKING LIST
Please follow the instructions below to ensure that your unit performs optimally:
• Read user manual and installation instructions in their entirety before installing unit.
• Ensure that (6) new, identical batteries are used when replacing batteries.
Old or mismatched batteries may damage the unit.
• Ensure that mounting surface is flat and free of dirt and debris before installing.
• Ensure that the unit is mounted at least 10" (25cm) above horizontal surfaces.
• Installation must be performed by a professional.
• Do not mount unit with reflective objects in its sensing distance.
• This unit is for indoor use only.
• This unit contains electrical devices and valves, handle with care.
• Disassemble unit with care to avoid damaging liquid feed line.
• Only clean unit with neutral detergents, and dry with a soft cloth.
• Do not clean unit with water or non-neutral detergents to avoid surface damage or
internal electrical failure. Only clean sensing area on underside of unit with a soft,
dry cloth to avoid sensing errors.
• Unit must be installed at least 14" above surfaces to avoid sensor malfunction.
• Open packaging and handle unit with care to avoid damage.
• Contact your distributor if any parts of the unit are missing or damaged before installation.
• Replacement part specifications are subject to change over time.
Contact your distributor in case of non-applicable replacement parts.
(1) Unit
(1) Installation Panel
(3) ST4x25 Screws
(3) Expansion Screws
(1) Key
(1) Installation Manual
(1) Certification
CAUTION

INSTRUCTION MANUAL  4
INSTALLATION
TIP: Ensure that unit is
mounted at least 14" (35
cm) above stainless steel or
other reflective countertop
surfaces.
>10" (25 cm)
7.9" (20 cm)
1. Place mounting bracket
where the unit will be secured
to the wall. Mark the locations
of the 3 holes.
2. Drill holes into the marked
areas of the mounting surface.
After holes are drilled, insert
expansion screw heads into
the corresponding holes.
3. Place mounting plate on
the wall, corresponding with
the expansion screw heads.
Then fasten mounting plate
with screws in corresponding
locations.
4. Line up grooves in back of unit with the
mounting plate, and slide dispenser into
bracket until it locks into place.
5. Push unit downward on the mounting bracket
until the connection is secure.

INSTRUCTION MANUAL  5
BATTERY INSTALLING & REPLACEMENT
HOW TO USE
1. Keep the body straight up
when the LED light is flashing.
2. Unscrew the screws and pick
out the battery container.
3. Insert or replace all batteries
(6 AA). Insert bracket into unit
and screw into place.
1. Insert key into lock on top of
the unit to open the top cover.
After batteries are installed,
hold the adjustment button for
3 seconds. The LED light will
flash 3 times to indicate that
the unit is on.
2. After top cover is removed,
open sealing cap and fill unit
with foam soap or sanitizer.
Clean any overflowing liquid
from the unit, and replace
the cap on the unit.
3. Wave hands under sensor
until soap or sanitizer begins
to dispense. Note that the unit
may require multiple senses
to activate before dispensing
soap or sanitizer.
Indicator
Key
Cap
Indicator
Quantity
Adjustment
Button
Sealing
Cap
Fixed
Bracket
Battery
Cover
Screw
CAUTION
WARNING
• After installing batteries, hold soap or sanitizer adjustment button for 3 seconds.
LED light will flash 3 times. At that point, the unit will enter standby mode.
Hold the soap or sanitizer adjustment button for 3 seconds to return the unit to sleep mode.
• Please keep batteries installed in unit even while in storage. If no use has been detected
in 72 hours, the unit will automatically run once in order to avoid tube adhesion.
• Children using the unit must be accompanied by an adult to avoid injury or malfunction.
• Please ensure proper disposal of depleted batteries.
• Keep unit dry at all times to avoid electrical malfunction.

INSTRUCTION MANUAL  6
QUANTITY ADJUSTMENT
• While unit is in standby, amount of soap or sanitizer
dispensed per activation can be adjusted with the
quantity adjustment button on top of the unit.
• Default output volume is roughly 1 ml per use.
• Output will be increased by .5ml per button press.
• There are 5 total levels of output, ranging from .5 - 2.5ml.
• Output may change slightly depending on type of liquid.
Quantity
Adjustment
Button
Indicator
TROUBLESHOOTING
• TIP: Keep fluid container clean and free of dirt and dust to avoid blockages.
Problem Reason Potential Solution
LED INDICATOR OFF
Control System Trouble Replace the Controller
Power Supply Problem Check Circuits and Batteries
Batteries - Poor Contact or Out of Power Reinstall or Replace Batteries
Circuits - Problem or Poor Contact Check Circuits
Indicator Sight Blocked Clean the Indicator Window
LED LIGHT FLASH Not Enough Power Replace Batteries
INDICATOR ON WITHOUT
SOAP OR SANITIZER
SUPPLY
Sensor Continue Working Remove Sensing Object
Out of Sensing Distance
Place Hand Directly Below
Sensor, Slowly Move Side to Side
and Up and Down Until Soap
Dispenses
Unit Fault Contact the Dealer
INSUFFICIENT SOAP OR
SANITIZER SUPPLY
Short Soap or Sanitizer Supply Time Adjust Soap or Sanitizer Output
Soap or Sanitizer is Too Viscous Reduce Soap or Sanitizer
Viscosity
Soap or Sanitizer Coagulation or
Obstruction
Try Clearing Lines or Contact the
Dealer