Noblelift ETF-30 manual 









Version06/2012
ETF‐SMS‐002_EN
INSTRUCTION HANDBOOK
Electric Lifting Table
WARNING
Do not use the lifting table before reading and
understanding these operating instructions.
NOTE:
Please check the designation of your
present type at the last page of this
document as well as on the ID-plate.
Keep for future reference.

1

2
FOREWORD
Before operating the lifting table, read this ORIGINAL INSTRUCTION HANDBOOK
carefully and understand the usage of the lifting table completely. Improper operation could
create danger.
This handbook describes the usage of different lifting tables. When operating and servicing
the lifting table, make sure, that it applies to your type.
Keep this handbook for future reference. If this or the warning/ caution labels are damaged
or got lost, please contact your local dealer for replacement.
ATTENTION:
Environmentally hazardous waste, such as batteries, oil and electronics, will have a
negative effect on the environment, or health, if handled incorrectly.
The waste packages should be sorted and put into solid dustbins according to the
materials and be collected disposal by local special environment protection bureau. To
avoid pollution, it’s forbidden to throw away the wastes randomly.
To avoid leaking during the use of the products, the user should prepare some
absorbable materials (scraps of wooden or dry duster cloth) to absorb the leaking oil in
time. To avoid second pollution to the environment, the used absorbable materials
should be handed in to special departments in terms of local authorities.
Our products are subject to ongoing developments. Because this handbook is only for
the purpose of operating / maintaining the lifting table, therefore please have
understanding, that there is no guarantee out of particular features out of this handbook.
NOTE: On this manual, the left sign means warning and danger, which can lead
to death or serious injury if not followed.
Copyright
The copyright remains with the company, mentioned on the CE- certificate at the end of this
document.

3
TABLE OF CONTENTS
1.CORRECT APPLICATION ............................................................................................4
2.DESCRIPTION OF THE LIFTING TABLE.....................................................................5
a.Overview of the main components.............................................................................5
b.Main technical data ....................................................................................................6
c.Description of the safety devices and warning labels.................................................6
d.Identification plate ......................................................................................................7
3.WARNINGS AND SAFETY INSTRUCTIONS ...............................................................8
4.COMMISSIONING, TRANSPORTING, STORAGE/ REASSEMBLING .........................9
a.Commissioning ..........................................................................................................9
b.Transporting...............................................................................................................9
c.Storage/ Reassembling..............................................................................................9
5.DAILY INSPECTION .....................................................................................................9
6.OPERATING INSTRUCTIONS ...................................................................................10
a.Parking.....................................................................................................................10
b.Lifting .......................................................................................................................10
c.Working at Height ....................................................................................................11
d.Lowering ..................................................................................................................11
e.Moving .....................................................................................................................11
f.Malfunctions.............................................................................................................11
g.Emergency...............................................................................................................12
7.CHARGING THE BATTERY .......................................................................................12
a.Installation and Removal..........................................................................................12
b.Charging ..................................................................................................................12
8.REGULAR MAINTENANCE........................................................................................13
9.TROUBLE SHOOTING ...............................................................................................16
10.WIRING/ CIRCUIT DIAGRAM.....................................................................................17
a.Electrical circuit diagram ..........................................................................................17
b.Hydraulic circuit........................................................................................................17
11.DECLARATION OF CONFORMITY (valid, if sold within the EU)................................18

4
1. CORRECT APPLICATION
It is only allowed to use this lifting table according to this instruction handbook.
This table is a mobile lifting table designed to lift or lower a clearly defined load.
Do not use this table for other purpose than its intended use.
A wrong usage can cause human injuries or can damage equipment.
The operator/ the operating company has to ensure the correct usage and has to ensure,
that this table is used only by staff, which is trained and authorized to use this table.
The table has to be used on substantially firm, smooth, level and prepared surfaces.
Driving with the load lifted is not allowed. The load must be placed approximately on the
longitudinal centre plane of the table. The capacity is marked on capacity sticker as well on
the Identification plate. The operator has to consider the warnings and safety instructions.
The table is intended to be used for indoor applications with ambient temperatures between
+5C and + 40C.
Operating lighting must be minimum 50 Lux.
Modification
No modifications or alterations to this lifting table which may affect, for example, capacity,
stability or safety requirements of the truck, shall be made without the prior written approval
of the original truck manufacturer, its authorized representative, or a successor thereof.
This includes changes affecting, for example braking, steering, visibility and the addition of
removable attachments. When the manufacturer or its successor approve a modification or
alteration, they shall also make and approve appropriate changes to capacity plate, decals,
tags and operation and maintenance handbooks.
By not observing these instructions, the warranty becomes void.

5
2. DESCRIPTION OF THE LIFTING TABLE
a. Overview of the main components
1 Loading platform
2 Lift mechanism
3 Hydraulic cylinder
4 Steering castors
5 Castor
6 Hydraulic aggregate
7 Parking brake
8 Battery
9 Charger
10 Voltmeter
11 Emergency button
12 Key switch
13 Charging indicator
14 Safety mechanism (metal bar)
15 Pushing/ Pulling bracket
16 Operator control panel
6
1
2
3
4
5
9
10
11
12
13
14
15
16
8
7
Fig.1: Overview

6
b. Main technical data
B
L
h1
h2
d
L1
h4
h3
TYPE
ETF 30 ETF 50 ETF 75 ETF D35
Capacity kg 300 500 750 350
Max table height h2mm 880 1025 970 1300
Min. table height h1mm 290 440 420 370
Table/ platform size (LxBxH) mm 850x500x50 1010x520x50 1000x510x55 910x500x53
Caster wheel- dimension x w mm 125x40 150x48 147x50 125x40
Overall length L1mm 1145 1305 1345 1210
Height of handle from the ground h3mm 920 970 935 920
Vertical lifting h4mm 590 585 550 930
Lifting speed with load/without load mm/s 65/94 65/94 70/80 90/110
Lowering speed with /without load mm/s 98/74 98/74 50/35 100/90
Lifting cycle (fully charged) app. 120 app. 100 app. 100 app. 100
Operating voltage V 24V 24V 24V 24V
Lifting motor kW 0.8 0.8 0.8 0.8
Battery capacity Ah
(C20)
30Ah
(4x12V15Ah)
24Ah
(2x12V24Ah)
30Ah
(4x12V15Ah)
30Ah
(4x12V15Ah)
Max. operating pressure MPa 16 16 16 16
Battery weight (+/-1.5kg) kg 18 17 18 18
Charger (built-in) 24V4A h 8.5Hr 8.5Hr 8.5Hr 8.5Hr
Protection code IP IP54 IP54 IP54 IP54
Approx lifting time to full height s 10 10 12 10
Net Weight (without battery) kg 116 157 160 142
Noise emission dB (A) < 70dB < 70dB < 70dB < 70dB
c. Description of the safety devices and warning labels
Fig. 2: Technical data
Table 1: Main technical data for standard version

7
A Capacity sticker (both sides, sample
for illustration only, capacity might be
different)
B Sticker finger shearing and crushing
(both sides)
C Identification plate (ID-plate)
D Not enter on platform sticker
E Brake sticker
F Sticker to read this instruction
G Prohibit decal
H Direction movement marking
(11) Emergency stop button
(14) Safety bar
The safety bar (14) must be folded out after the platform is lifted to ensure that neither
crushing nor shearing risk can arise from unintended lowering or malfunctions. Before
lowering it must be back into its initial position.
The lifting table has an emergency stop button (11), which stops all lifting/ lowering
functions in emergencies. To activate this function, push this red button. Before deactivating
this function by turning and pulling this button, make sure, that there are no failures
according to the pre-shift checks, described in chapter 4 and that the dangerous situation or
failure is eliminated and the lifting table is not damaged.
DO NOT ENTER UNDER THIS PLATFORM UNLESS IT IS MECHANICALLY LOCKED
DO NOT PUT HANDS OR FEET UNDER THE PLATFORM
d. Identification plate
1 Designation, type 2 Serial number
11
14
H
Fig. 3: Safety and warning labels

8
3 Own mass/ net weight in kg
4 IP- Protection code
5 Max. operating pressure in MPA
6 Supply voltage in V
7 Nominal power in kW
8 Name and address of the manufacturer
9 Allowed load distribution
10 Lift category 2 according to EN 1570
11 Rated capacity in kg
12 Manufacturing date
3. WARNINGS AND SAFETY INSTRUCTIONS
DO NOT
Put foot or hand in the scissors lifting mechanism.
Allow other person then the operator to stand in front of or behind the table when it is
moving or lifting/lowering.
Move the table when table is in raised position. Load could fall down.
Enter under table.
Overload the table.
Put foot in front of rolling wheel, Injury could result.
Use the table on a slope or inclined surface, the table may become uncontrollable
and create danger.
Lift people. People could fall down and suffer severe injury.
Watch difference in floor levels when moving the lifter. Load could fall down or the lifting
table could get uncontrollable.
DO NOT
Lower table too fast. Load could fall down and create danger. Lower speed controller
is available for safety purpose.
Fig. 4: Identification plate 8
1
2
10
12
4
3
11
If sold to the EU, here
the place of the CE
marking
5
6
7
9

9
Side or end load. Load must be distributed on at least 80% of table area.
Use table with unstable, unbalanced loosely stacked load.
Use table without manufacturer’s written consent.
Supply on board charger with AC voltage other than 110V or 220V.
Keep watching the condition of load. Stop operating table if load becomes unstable. Brake
table and activate the emergency button by pushing when sliding load on or off the table.
Practice maintenance work according to regular Inspection. This table is not designed to be
water resistant. Use table under dry condition. Prolonged continuous operation might cause
damage of the power pack. Stop operation if temperature of hydraulic oil is too high.
4. COMMISSIONING, TRANSPORTING, STORAGE/
REASSEMBLING
a. Commissioning
For the commissioning following information are relevant:
Type ETF 30 ETF 50 ETF 75 ETF D35
Commissioning weight app. 140 kg app. 177 kg app. 180 kg app. 162 kg
Dimensions [mm] 1260x620x645 1420x670x680 1480x735x700 1360x590x640
After receiving this lifting table you have to do following before firstly operating the table:
Check if all parts are included and not damaged
Installation of the pulling/pushing bracket (15).
Eventually installation of the batteries according to chapter 7.
Charging the batteries according to chapter 7.
Do the work according to the daily inspections as well as functional checks.
b. Transporting
For transporting, remove the load, lower the table to the lowest position and fix the table
lash the table safe with dedicated lashing straps.
c. Storage/ Reassembling
For storage, remove the load, lower the table to the lowest position, grease all in this
handbook mentioned greasing points (regularly inspection) and eventually protect the
table against corrosion and dust. Jack the table safety, so that there will be no flattening
after storage. For reassembling remove the pushing/ pulling bracket (15) in the opposite
way you assembled this before.
5. DAILY INSPECTION
This chapter describes pre-shift checks before putting the truck into operation. Daily
inspection is effective to find the malfunction or fault on this table. Check table on the
Table 2: Commissioning data

10
following points before operation. Remove load from table and when servicing, please use
the safety mechanism (14) to prevent table from lowering.
DO NOT USE THE TABLE IF ANY MALFUNCTION OR FAULT IS FOUND.
HYDRAULIC LEAKAGE CAN CAUSE MALFUNCTIONS AND LOSS IN THE LIFTING
FUNCTION.
Check for scratch, bending or cracking on the table.
Check if there is any oil leakage from the cylinder.
Check the vertical creep of table.
Check the smooth movement of the wheels.
Check the function of the brake.
Check if all the bolts and nuts are tightened firmly.
Check the storage level by turning the circuit breaker on.
Check the lifting and lowering conditions by switching buttons on.
Check if there are broken hoses or broken electric wires by eyes.
6. OPERATING INSTRUCTIONS
When operating the lifting table, the operator has to wear safety shoes.
The table is intended to be used for indoor applications with ambient temperatures
between +5C and + 40C.
The operating lighting must be minimum 50 Lux.
It is not allowed to use the table on angled surfaces!
a. Parking
Brake the table when not moving it in order to prevent sudden movement.
The brake (7) is equipped with the swivel caster on the right.
Braking, press the brake pedal (7).
Releasing, lift up the brake pedal (7).
Turn the key switch (12) to the “off” position
and remove the key.
b. Lifting
Do not overload table. Stay within the rated capacity.
Do not side or end load. Load must be distributed on at least 80% of table area (1).
Prolonged continuous working might cause damage of hydraulic power pack.
Stop operation if temperature of hydraulic oil is too high.
Do not lift people. People could fall down and suffer severe injury.
Before lifting a load, ensure that the load is stable and can’t fall down; in case of
doubt, fix the load with designated lashing equipment.
Insert the key into the key- switch (12). Turn the key- switch to the “On” position
(Eventually deactivate the emergency button (11).
Press the switch for lifting on the operator control panel (16) and the table lifts up to the
desired position ranging vertical travel. Load only the designated capacity, which is:
Fig. 5: Parking brake

11
14
ETF 30 300 kg
ETF 50 500 kg
ETF 75 750 kg DO NOT OVERLOAD THE TABLE!
ETF D35 350 kg
The capacity sticker (A) shall be clearly and permanent visible from the operating
position.
c. Working at Height
While working at height the safety mechanism (14) must
be activated to prevent unintended lowering, what can cause
permanent injuries or damages.
If the table is lifted, move/ turn out the safety mechanism (14).
Before lowering, turn this metal bar back to its initial position.
d. Lowering
Do not put foot or hand in scissors mechanism.
Do not lower table with load too fast and stop suddenly. Impact load could be created
and table could be damaged.
Insert the key into the key- switch (12). Turn the key- switch to the “On” position
(Eventually deactivate the emergency button (11).
Press the switch for lowering on the operator control panel (16) and the table lowers
down to the desired position ranging vertical travel.
e. Moving
DO NOT
Move the table on a slope or inclined surface. Lifting table may become
uncontrollable and create danger.
Allow other person stand in front of or behind table when it is moving.
Move table when table is in raised position. Load could fall down.
Put foot in front of rolling wheels. Injury could result.
Move the table if the visibility is insufficient.
Watch difference of floor level when moving lifter. Load could fall down.
Make the load stable to prevent it from falling down.
Lower the table down before moving.
Release the brake (7) and move the table by pushing or pulling the pushing/ pulling
bracket (15).
Keep watching the condition of load. Stop operating the table if load becomes unstable.
f. Malfunctions
If there are any malfunctions or the table is inoperative, please stop using the lifting
table and activate the emergency button (11) by pushing it. Place the table at a safe
Fig. 6: Safety mechanism

12
place, if possible/necessary activate the safety mechanism (14) against lowering, park
the table on a safe area by activating the parking brake (7) and lock the lifting table with
the key (12). Inform immediately the manager and, or call your service. Start operating
the table only if the reason for the malfunction was investigated and repaired.
g. Emergency
In emergencies, push the emergency button (11). All electrical functions will be stopped.
Keep safe distance. If possible activate the parking brake.
7. CHARGING THE BATTERY
It is only allowed to use the in this chapter specified batteries.
These batteries are maintenance free; re- filling is prohibited.
Recycling of batteries undergoes national regulations. Please follow these regulations.
By handling batteries, open fire is prohibited.
In the area of battery charging neither burning materials nor burning liquids are allowed.
Smoking is prohibited and the area must be ventilated.
The charger (9) is especially developed for the use with this lifting table. It offers
automatic detection and tracking of the battery, until the charging is automatically
completed.
The lifting table is equipped with “maintenance free” sealed liquid acid batteries.
oETF 30/ ETF 75/ ETF D35 4 x 12V 15 Ah / Type BT-12M15AC
oETF 50 2 x 12V 24 Ah / Type BT-12M24AT
a. Installation and Removal
Install the batteries to the lifting table by opening the cover and inserting the batteries
carefully. Prevent to have short-cuts during the installation.
Fix the connectors accordingly and consider the right connection of the battery poles.
Finally assemble the cover.
The removal is in the opposite direction.
b. Charging
The attached automatic charger is only available for the optional voltage of 110V or
220V as referred.
Check the wiring or confirm AC voltage when AC power Indicator of the charger shows
abnormal by red flashlight.
Charging is necessary, if the battery voltage is lower
than 9,6V. The voltage is shown on the voltmeter (10).

13
12
11
13
9
10
Fig. 7: Charger
Turn off the lifting table by turning the key switch (12) to
the “off”- position.
Connect the charger (9) with the included cable to the
power socket.
Charging starts automatically.
The switch of charger turns off automatically, if
the battery reaches 80% capacity or exceeds 12
hours in charging condition.
Disconnect the charger with the power socket and
store the charging cable for further charging-
operations.
The charging indicator (13) shows the charging
voltage, the connection to the battery (battery-symbol
is lighting), the charging-function (Power-symbol is lighting)
as well as the finished charging (full-symbol is lighting).
8. REGULAR MAINTENANCE
Only qualified and trained personnel are allowed to do service on this lifting table.
Before servicing the table, remove the load and during servicing use the safety
mechanism (14).
If you need to lift the table, remove the battery and use designated lashing
equipment. Before working, put safety devices (for instance designated lift jacks)
under the table to protect against accidental lowering.
Use approved and from your dealer released original spare parts.
Please consider that oil leakage of hydraulic fluid can cause failures and accidents.
It is allowed to adjust the pressure valve only from trained service technicians.
If you need to change the wheels, please follow the instructions above. The castors
must be round and they should have no abnormal abrasion.
Remove load from table and when servicing lifter, please use safety stopper to
prevent table from lowering.
Check the items emphasized in daily inspection (daily).
Lubricate with grease the rails where roller moves. Also lubricate the grease nipples
(monthly).
Lubricate all the pivoting points and axles (every 6 months).
Replace the hydraulic oil (every 12 months).
The required hydraulic fluid- type is:
oYA-N46
oviscosity is 41.4-50.6
oamount 2,5L

14
For refilling the hydraulic fluid, you need to unscrew the hydraulic power pack and
place this vertically. Then you can remove the oil tank and it is possible to check and
refill the oil. Assembling must be done in the opposite direction. For this work please
call the service.
If you need to replace the hydraulic hoses, use only dedicated original parts
according to the spare parts list.
Waste material like oil, used batteries or other must be probably disposed and recycled
according to the national regulations and if necessary brought to a recycling company.
Before starting operating the lifting table check, if all markings and decals are in the right
place and not damaged (acc. to chapter 2 c ). If necessary replace the decals. If major
repair or replacement to a load supporting member of the lifting table has been carried out,
following tests needs to be carried out. For this you need to have special skills.
FOR THIS PLEASE CALL YOUR NEXT DEALER OR SERVICE!
Table 3: Checking after major repair or replacements
Lifting table Practical test according to EN 1570
Content Requirement Data (if required)
Ok/
not ok
1 Function of the controls. Ok/ not ok
2 Emergency stop, Brakes, Safety bar, Safety switches Ok/ not ok
3 Lift table through one complete cycle. 0 x Q max.
4 Operate the lifting table through one complete cycle. 1 x Q max.
5 Lifting and lowering time (operated with the full load) [s]
6 Vertical creep with Q max. 10min. < 5mm
7 Maintenance blocking device under the platform 1 x Q max.
8 Dynamic test 1.1x Q max. / 1cycle
9 Pressure valve, use locking glue. Pressure valve <110%
10 Static test (raised height and max. stress on the
structure)
1.25xQ max.
11 Visual check (by normal vision) No deformation or
damage of all parts
12 Operation of braking or holding devices. Ok/ not ok
13 Additionally equipment operation. Ok/ not ok
14 Overturning conditions 0.5x Q max. sideways

15
Table 4: Maintenance Logbook
Regular Maintenance Logbook
Date Name Comments Re-
start Date Name Comments
Re-
start

16
9. TROUBLE SHOOTING
If the table has malfunctions follow the instructions, mentioned under chapter 7 f.
Table 5: Trouble shooting
TROUBLE CAUSE REPAIR
Faulty wiring Check the wiring referring to the
actual wiring diagram.
Battery cord is disconnected. Connect the battery cord.
Table does not rise
while motor does
not run. Battery charge is insufficient. Charge the battery.
Faulty relief valve adjustment Adjust relief valve again.
Faulty hydraulic pump. Replace power pack.
Table does not rise
while motor runs. Shortage of hydraulic oil. Add oil.
Oil leakage in the lowering valve. Replace the lowering valve.
Vertical creep of
table Oil leakage from hydraulic circuit Check hydraulic circuit and
repair.
Oil leakage from
cylinder
Faulty sealing. Replace sealing.
Oil leakage from
piping or joint.
Insufficient tightening. Tighten joint again.
Oil leakage from
air breathing
Excessive quantity of oil. Reduce oil quantity.
Battery fail to be
charged
Battery is worn out. Replace battery
Charger is not connected correctly. Connect the charger correctly.
Charger shows
abnormal by red
flash Poles are reverse connected. Interchange the connection of
poles

17
10. WIRING/ CIRCUIT DIAGRAM
a. Electrical circuit diagram
b. Hydraulic circuit
Fuses
FU1 = 60A
FU2= 3A
FU1
FU2
Fig. 8: Electric
diagram
Fig. 9: Hydraulic Circuit

18
11. DECLARATION OF CONFORMITY (valid, if sold within the EU)
[GB] CE Declaration of Conformity
The signatory hereby declares that the specified machine conforms to the EU Directive 2006/42/EC (Machine Directive) and 2004/108/EEC
(Electro-Magnetic Compatibility, EMC) including their amendments as translated into national legislation of the member countries. The signatory is
individually authorized to compile the technical documents.
[D] EG-KONFORMITÄTSERKLÄRUNG
Der Unterzeichner bescheinigt hiermit, dass die im Einzelnen bezeichnete Maschine den Europäischen Richtlinien 2006/42/EG (Maschinenrichtlinie)
und 2004/108/EWG (Elektromagnetische Verträglichkeit - EMV) einschließlich deren Änderungen sowie dem entsprechenden Rechtserlaß zur
Umsetzung der Richtlinien in nationales Recht entspricht. Der Unterzeichner ist bevollmächtigt, die technischen Unterlagen zusammenzustellen.
[E] DECLARACIóN DE CONFORMIDAD CE
El signatario certifico por medio de la presente que la máquina especificada cumple con las Normas Europeas 2006/42/CE (Normativa para
maquinarias) y 2004/108/CE (Compatibilidad electromagnética), incluyendo sus respectivas odificaciones, así como con el decreto-ley para la
adaptación de las normas al derecho nacional. El signatario dispone de una autorización individual que le permite compilar la documentación técnica.
[F] DECLARATION DE CONFORMITE CE
Par la présente déclaration, les soussignés certifient que le machines spécifié ci-dessus est conforme à la loi et aux directives européennes 2006/42/CE
(directive sur les machines) et 2004/108/CEE (compatibilité électromagnétique - CEM), y compris aux modifications qui y sont apportées et à l’arrêté
autorisant sa transposition en droit national. Chaque signataire est habilité à établir individuellement la documentation technique.
[NL] EG-CONFORMITEITSVERKLARING
Ondergetekenden verklaren hierbij dat - volgens de nationale wetgeving van de Lidstaten - de hierboven vermelde opgegeven machina beantwoordt
aan de bepalingen qua veiligheid bij machines (EG richtlijn 2006/42/EC) en electro-magnetische compatibilteit (EG richtlijn 2004/108/EEC).
Ondergetekenden zijn ieder individueel gemachtigd het technisch dossier samen te stellen.
[P] DECLARAÇÃO DE CONFORMIDADE CE
Pela presente, os signatários certificam que o máquina especificado está conforme às Directivas Europeias 2006/42/CE („Máquinas“) e 2004/108/CEE
(„Inocuidade Electromagnética - IEM“), incluindo as alterações das mesmas e o respectivo decreto-lei para a transposição em lei nacional. Cada um
dos signatários está autorizado a proceder à elaboração da documentação técnica.
[I] DICHIARAZIONE DI CONFORMITÀ CE
I sottoscritti dichiarano che il veicolo per trasporti interni a macchina specificato soddisfa le Direttive Europee 2006/42/EC (Direttiva Macchine) e
2004/108/EEC (Compatibilità elettromagnetica - EMV) comprese le relative modifiche, come pure il rispettivo decreto legislativo per la conversione delle
direttive in diritto nazionale. I sottoscritti sono singolarmente autorizzati alla creazione della documentazione tecnica.
[BG] EВРОПЕЙСКА ОБЩНОСТ - ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ
Подписаните удостоверяват снастоящето, че подробно описаното машина средство отговаря на европейския норматив 2006/42/EG (норматив
за машини) ина 2004/108/EG (електро-магнетична съвместимост), включително стехните промени, както ина съответния указ за прилагане
на нормативите внационалното право. Подписаните при това са упълномощении поотделно да съставят техническата документация.
[CZ] EG - PROHLÁŠENÍ O SHODĚ
Níže podepsaný tímto potvrzuje, že podrobný popis uvedené stroje odpovídá Evropským směrnicím 2006/42/EC (směrnice pro stroje) a 2004/108/EEC
(elektromagnetická interference - EMV) včetnějejich pozdějších úprav, jakož i příslušným právním výnosům pro uplatnění příslušné směrnice v rámci
národního práva. Každý z podepsaných jsou jednotlivězplnomocněni k vytvoření technických podkladů.
[DK] EF-OVERENSSTEMMELSESERKLÆRING
Undertegnede attesterer hermed, at det specificerede maskine stemmer overens med de Europæiske Direktiver 2006/42/EU (maskindirektiv) og
2004/108/EØF (elektromagnetisk kompatibilitet - EMC) samt med den modsvarende lovvedtagelse til implementering af direktiver i den nationale
lovgivning. De undertegnede er hver for sig beføjet til at sammenstille de tekniske dokumenter.
[EST] EL vastavusavaldus
Allakirjutanud tõendavad käesolevaga, et üksikasjaliselt kirjeldatud täpsustatud masin vastab Euroopa direktiividele 2006/42/EÜ (Direktiiv masinate
kohta) ja 2004/108/EMÜ (Elektromagnetiline sobivus - EMS) kaasa arvatud nende muudatused ja nendele vastavatele õigusmäärustele direktiivide
muutmiseks siseriiklikuks õiguseks. Iga allakirjutanu üksikult on volitatud koostama tehnilist dokumentatsiooni.
[FIN] EU-YHDENMUKAISUUSSELOSTUS
Allekirjoittaneet todistavat täten, että kukin erikseen mainittu omalla voimanlähteellä varustettu tehdaskone vastaa EU-direktiivien 2006/42/EC
(koneenrakennusdirektiivi) ja 2004/108/EEC (sähkömagneettinen yhteensopivuus – EMC) määräyksiä sekä niiden muutoksia ja niiden kansalliseen
lainsäädäntöön soveltamista koskevaa oikeussääntöä. Jokaisella allekirjoittaneista on oikeus itsenäisesti laatia
asiaankuuluvia teknisiä asiakirjoja.
[GR] ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΟΚ
Οι υπογράφοντες βεβαιώνουν διά της παρούσης ότι το συγκεκριμένο μηχάνημα συμμορφώνεται προς την Κοινοτική Οδηγία 2006/42/ΕΚ
(«Μηχανήματα») και 2004/108/ΕΟΚ (Ηλεκτρομαγνητικής Συμβατότητας, ΗΜΣ), καθώς και οι τροποποιήσεις τους, όπως μεταφράστηκε στην εθνική
νομοθεσία των χωρών μελών. Οι υπογράφοντες είναι σε κάθε περίπτωση εξουσιοδοτημένοι ατομικά να καταρτίσουν τα τεχνικά έγγραφα.
[H] EU KONFORMITÁSI NYILATKOZAT
Alulírottak ezennel igazolják, hogy a részletesen leírt a megadott gép megfelel a 2006/42/EC (Gép-Irányelv) és a 2004/108/EEC (Elektromágneses
összeférhetőség - EMV) Európai Irányelveknek, beleértve azok módosításait, valamint az irányelvek nemzeti jogba történőátültetésére irányuló
megfelelőjogi rendelkezést. Továbbá az alulírottak mindegyike rendelkezik meghatalmazással arra nézve,
hogy összeállíthatja a műszaki dokumentációt.
[LT] ES atitikimơdeklaracija
Žemiau pasirašęasmenys patvirtina, kad atskirai aprašytas nurodyta mašina atitinka Europos Sąjungos direktyvas 2006/42/EB (Mašinųdirektyva) ir
2004/108/EEB (Elektromagnetinis suderinamumas – EMS) įskaitant jųpakeitimus, o taip pat ir atitinkamąteisės aktądėl direktyvųįgyvendinimo
nacionalinėje teisėje. Kiekvienas iš pasirašiusiųasmenųturi teisęruošti techninędokumentaciją.
[LV] ES atbilstības deklarācija
Ar zemāk redzamajiem parakstiem tiek apliecināts, ka norādīts mašīna atbilst Eiropas Savienības normatīvām 2006/42/EG (Mašīnu normatīvas) un
2004/108/EWG (Elektromagnētiskāatbilstība – EMV), ieskaitot to izmaiņas, kāarīatbilstošos tiesiskos rīkojumus normatīvu pielāgošanai nacionālajai
likumdošanai. Parakstu īpašnieki ir atsevišķi pilnvaroti sastādīt tehniskās dokumentācijas.
[N] EU-KONFORMITETSERKLÆRING
Undertegnede bekrefter hermed at de enkelte betegnede maskin med kraftdrift tilsvarer de europeiske retningslinjene 2006/42/EC (maskinretningslinje)

19
og 2004/108/EEC (elektromagnetisk fordraglighet - EMV) inklusiv disses endringer og den tilsvarende rettsforordning til omsetning av nasjonal rett. Hver
undertegnede er fullmektig til å sette sammen de tekniske dokumentene.
[PL] DEKLARACJA ZGODNOŚCI Z NORMAMI UE
Niżej podpisani potwierdzająniniejszym, że opisany tutaj, napędzany określona maszyna spełnia wymagania określone w dyrektywach Europejskich
2006/42/EC (Maszyny) i 2004/108/EEC (Nieszkodliwość elektromagnetyczna - EMC) wraz z ich późniejszymi zmianami oraz odpowiednimi
rozporządzeniami mającymi na celu przekształcenie tych dyrektyw w prawo krajów członkowskich. Niżej podpisani sąpojedynczo upoważnieni do
zestawiania dokumentacji technicznej.
[RO] DECLARAŢIE DE CONFORMITATE CE
Subsemnaţii adeveresc prin prezenta căvehiculul de specificat maşinădescris individual corespunde directivelor europene 2006/42/CE (Directiva
privind maşinile) şi 2004/108/CEE (Compatibilitatea electromagnetică- CEM) inclusiv modificărilor lor precum şi actului legislativ corespunzător prentru
transpunerea directivelor în drept naţional. Subsemnaţii sunt fiecare în parte împuterniciţi săîntocmeascădocumentaţia tehnică.
[RUS] Декларация соответствия стандартам ЕС
Настоящим лица, подписавшие документ, удостоверяют, что машина суказанной спецификацией соответствует европейским стандартам
2006/42/EG (Транспортная директива) и2004/108/EWG (Электромагнитная совместимость - ЕМС), включая изменения вних, атакже
соответствующим национальным стандартам инормам. Каждое по отдельности лицо, подписавшее документ, имеет полномочия для
составления технической документации.
[S] EG-KONFORMITETSFÖRKLARING
Undertecknarna intygar härmed att det i detalj betecknade maskin uppfyller de Europeiska direktiven 2006/42/EG (Maskindirektiv) och 2004/108/EEG
(Elektromagnetisk tålighet - EMV), inklusive ändringarna i detta och den motsvarande rättsförordningen för att omsätta direktiven i nationell rätt.
Undertecknarna har var för sig fullmakt att sammanställa den tekniska dokumentationen.
[SK] vyhlásenie o zhode
Dolu podpísaní týmto potvrdzujeme, že podrobný popis uvedené stroje Zodpovedá Európskym smerniciam 2006/42/EC (ernica
pre stroje ) a 2004/108/EWG ( elektromagnetická tolerancia – EMV ) vrátane jeho neskorších úprav, rovnako zodpovedá aj príslušným právnym
nariadeniam na uplatnenie smerníc v rámci národného práva. Každý z podpísaných je jednotlivo splnomocnený na vytvorenie technických podkladov.
[SLO] EU IZJAVA O SKLADNOSTI
Podpisani s tem potrjujemo, da posamično označeno določeno stroj vozilo odgovarja Evropski direktivi 2006/42/EC (Direktiva o strojih) in 2004/108/EEC
(Elektromagnetna skladnost - EMV) vključno z njihovimi spremembami ter ustrezno pravno uredbo o prevzemu smernic v nacionalno pravo. Podpisniki
so vsakokrat posamezno pooblaščeni za izdajanje tehnične dokumentacije.
[TR] AB Uygunluk Açıklaması
İmza sahibi şahıslar, ayrıntılarıbelirtilen makine aracının, 2006/42/EC (Makine Yönergesi) ve 2004/108/EEC (Elektromanyetik Uyumluluk – EMC) no'lu
Avrupa Yönergelerine ve bunların değişiklik sonucu oluşan metinlerine ve yönergelerin milli hukuk hükümlerine dönüştürülmesine dair ilgili hukuk
kararnamesine uygun olduğunu tasdik ederler. İmza sahibi şahıslar teknik dosyalarıbir araya getirmek için münferiden vekil tayin edildi.
(1) Type/ Typ/ Tipo/ Modello/ Tyyppi/ Tipo / ΤYΠΟΣ/ Típus/ Tip/ Тип/ Tips/ Tipas/ Tüüp:
(2) Serial No./ Serien-Nr./ N°. de série/ Serienummer/ Nº de serie/ Numero di serie/ Serienr./ Sarjanro/ αυξάνων αριθμός/ Seriové číslo/ Szériaszám/
Nr.Seryjny/ Serijska številka/ Výrobné číslo/ Серийный номер/ Seri No./ Seerianr./ Sērijas Nr./ Serijos numeris:
(3) Year of constr./ Baujahr/ Année de constr./ Bouwjaar/ Año de constr./ Anno di costruzione/ Produktionsår/ Byggeår/ Tillverkningsår/ Valmistusvuosi /
Ano de fabrico / έτος κατασκευής/ Rok výroby/ Gyártási év/ Rokprodukcji / Letnik / Год изготовления / Üretim yılı/ Väljalaskeaasta / Izgatavošanas
gads / Gamybosmetai
(4) Manufacturer or his authorized representative in Community/ Hersteller oder in der Gemeinschaft ansässiger Vertreter/ Fabricant ou son mandataire
établi dans la Communauté/ Fabrikant of zijn in de Gemeenschap gevestigde gemachtigde/ Fabricante o representante establecido en la
Comunidad/ Construtor ou Representante estabelecido na Comunidade/ Costruttore oppure il suo rappresentante nella Comunità/ Fabrikant eller
dennesi Fællesskabet etablerede befuldmægtigede/ Produsent eller agent innen felleskapet/ Tillverkare eller representant inom EU/ Valmistaja tai
yhteisömaassa oleva edustaja / V˘robce nebo jeho zastoupení/ Gyártó / producent albo jego przedstawiciel w EG (Wspólnota Europejska)/
Καηαζθεπαζηήο ήόκηινο ηνπηθώλ αληηπξνζώπσλ/ Üretici ya da Bölgedeki Yetkili Temsilci/ Proizvajalec ali pooblaščeni zastopnik s sedežem v EU/
Výrobca alebo zástupca so stálym bydliskom v EÚ / Изготовитель или его представитель, зарегистрированный встране Содружества/ Tootja
või organisatsioonis paiknev esindaja/ Ražotājs vai vietējais uzņēmuma pārstāvis / Gamintojas arba šalyje reziduojantis atstovas:
(5) Date/ Datum/ Data/ Fecha/ datum/ Dato/ päiväys/ Kuupäev/ Datums/дата / Dátum/ dátum/ tarih/ ημερομηνία
(6) Authorised signatory/ Im Auftrag/ pour ordre/ Incaricato/ Por orden de/ por procuração/ op last van/ på vegne af/ på uppdrag/ Etter oppdrag/ psta./
Ülesandel / pavedus / v.i. / По поручению / megbízásából /длъжностно лице / z pověření / z poverenia / po nalogu / na polecenie / din sarcina /
adına / θαη' εληνιή
If you can read this text:
- Your truck might be sold outside the
EU; this declaration is then not valid.
- Or the declaration is not complete.
In this case please ask for a copy