Nobles Magna Twin 3000 Product manual

Wide Area Vacuum
Magna Twin3000
Model No.:
608577 – 120V
609227 – 120V CSA
Operator and Parts Manual
608582
Rev. 01 (03-04)
NOBLES CUSTOMER SERVICE:
1–800–365–6625
FAX: [phone]
TECHNICAL SUPPORT:
1–800–522–7839 EXT. 5356
TENNANT COMPANY
701 NORTH LILAC DRIVE
MINNEAPOLIS, MN 55422
MAILING ADDRESS:
TENNANT COMPANY
P.O. BOX 1452
MINNEAPOLIS, MN 55440–1452

OPERATION
2Magna Twin t3000 (03–04)
This manual is furnished with each new model.
It provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
Use the illustrated Parts Lists to order parts. Before
ordering parts or supplies, be sure to have your
machine model number and serial number handy.
Parts and supplies may be ordered by phone or mail
from any authorized parts and service center,
distributor or from any of the manufacturer’s
subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine care instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
MACHINE DATA
Please fill out at time of installation for future reference.
ModelNo.-
Install. Date -
Serial No.-
E1999, 2004 Tennant Company Printed in U.S.A.
Nobles is a registered United States trademark of Tennant Company.
Magna Twin is a United States trademark of Tennant Company.
TABLE OF CONTENTS
SAFETY PRECAUTIONS 3. . . . . . . . . . . . . . . . . . . .
GROUNDING INSTRUCTIONS 4. . . . . . . . . . .
SAFETY LABELS 4. . . . . . . . . . . . . . . . . . . . . . . . . . .
MACHINE SETUP 5. . . . . . . . . . . . . . . . . . . . . . . . . .
MACHINE OPERATION 5. . . . . . . . . . . . . . . . . . . . .
HOSE ATTACHMENT OPERATION 6. . . . . . . .
MACHINE MAINTENANCE 6. . . . . . . . . . . . . . . . . .
DAILY MAINTENANCE 6. . . . . . . . . . . . . . . . . . .
WEEKLY MAINTENANCE 7. . . . . . . . . . . . . . . .
QUARTERLY MAINTENANCE 7. . . . . . . . . . . .
ROUTINE ADJUSTMENTS 7. . . . . . . . . . . . . . . . . .
BRUSH ADJUSTMENT 7. . . . . . . . . . . . . . . . . .
BELT ADJUSTMENT OR REPLACEMENT 8.
STORING MACHINE 8. . . . . . . . . . . . . . . . . . . . . . . .
RECOMMENDED STOCK ITEMS 8. . . . . . . . . . . . .
TROUBLE SHOOTING 9. . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS 10. . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL DIAGRAMS 11. . . . . . . . . . . . . . . . . . .
PARTS LIST 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPPER HOUSING GROUP 12. . . . . . . . . . . . . . .
LOWER HOUSING GROUP 14. . . . . . . . . . . . . .
CONSOLE GROUP 16. . . . . . . . . . . . . . . . . . . . . .
OPTIONS 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WAND AND HOSE KIT 17. . . . . . . . . . . . . . . . . . .

OPERATION
Magna Twin t3000 (03–04) 3
SAFETY PRECAUTIONS
This machine is intended for commercial use only.
It is designed exclusively to pick up dirt, dry
debris and dust in an indoor environment and is
not constructed for any other use. The pick up of
any type of fluid or dangerous/toxic materials is
prohibited. Use only recommended accessories.
All operators must read, understand and practice
the following safety precautions.
The following warning alert symbol and the “FOR
SAFETY” heading are used throughout this manual as
indicated in their description:
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
Failure to follow these warnings may result in:
personal injury, electrocution, electric shock, fire
or explosion:
WARNING: Do Not Use Flammable Liquids Or
Operate Machine In Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
This machine is not equipped with explosion
proof motors. The electric motors will spark upon
start up and during operation which could cause a
flash fire or explosion if machine is used in an
area where flammable vapors/liquids or
combustible dusts are present.
WARNING: Do Not Pick Up Flammable Or
Toxic Materials, Burning Or Smoking Debris.
WARNING: Do Not Operate With Damaged
Power Cord. Do Not Modify Plug. Unplug Power
Cord Before Servicing Machine
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
WARNING: Do Not Use Outdoors Or On Wet
Surfaces. Do Not Expose to Rain. Store Indoors.
The following information signals potentially
dangerous conditions to the operator or
equipment:
FOR SAFETY:
1. Do not operate machine:
– In flammable or explosive areas.
– Unless trained and authorized.
– Unless operator manual is read and
understood.
– Unless cord is properly grounded.
– With damaged cord or plug.
– If not in proper operating condition.
– On wet or damp surfaces.
– In outdoor areas.
– Without bag and/or filters in place.
– With the use of an extension cord.
2. Before operating machine:
– Make sure all safety devices are in place
and operate properly.
3. When using machine:
– Do not pull machine by plug or cord.
– Do not pull cord around sharp edges or
corners.
– Do not close doors on cord.
– Do not unplug by pulling on cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated surfaces.
– Do not pick up burning or smoking debris,
such as cigarettes, matches or hot ashes.
– Report machine damage or faulty
operation immediately.
– Never allow children to play on or around.
4. Before leaving or servicing machine:
– Turn off machine.
– Unplug cord from wall outlet.
5. When servicing machine:
– Unplug cord from wall outlet.
– Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves.
– Use manufacturer supplied or approved
replacement parts.
– All repairs must be performed by a
qualified service person.
– Do not modify the machine from it’s
original design.

OPERATION
4MagnaTwin t3000 (03–04)
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment–grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
Grounded
3 Hole Outlet
Ground Pin
SAFETY LABELS
The safety labels appear on the machine in the
locations indicated. Replace labels if they become
damaged or illegible.
WARNING LABEL – LOCATED ON
BACKSIDE OF MACHINE.
WARNING LABEL –
LOCATED INSIDE OF
MACHINE ON VACUUM
MOTOR COVER.
WARNING LABEL –
LOCATED ON BACK-
SIDE OF MACHINE.
WARNING: Moving
fan blades. Keep
away.

OPERATION
MagnaTwin t3000 (03–04) 5
MACHINE SETUP
1. Install selected filter bag by opening bag access
door and sliding rubber collar on bag completely
onto the intake chamber. Make sure bag is totally
within housing before closing door (Figure 1).
FOR SAFETY: Do not operate machine without
bag and/or filters in place.
FIG.
1
ATTENTION: To maintain best performance, empty
filter bag when 2/3 full.
2. Plug power cord into 120V grounded wall outlet
(Figure 2).
FOR SAFETY: Do not operate machine unless
cord is properly grounded.
WARNING: Do Not Operate With Damaged
Power Cord. Do Not Modify Plug. Unplug Power
Cord Before Servicing Machine.
Grounded
3 Hole Outlet
Ground Pin
FIG.
2
3. Properly adjust brush height to type of carpet, tilt
machine back and turn adjustment knob
counterclockwise. Now tilt machine back down to
floor and activate triggers. If a slight forward
propulsion is noticed, machine is properly adjusted
(Figure 3).
FIG.
3
NORMAL BRUSH ADJUSTMENT RANGES:
THICK PILE CARPET 11 TO 8. . . . . . .
MEDIUM PILE CARPET 7 TO 4. . . . .
LOW PILE CARPET 3 TO 1. . . . . . . . .
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
1. Turn on vacuum switch, located on control
console. Make sure air flow control knob is pushed
in all the way to direct air flow to brush area
(Figure 4).
FOR SAFETY: When using machine, do not pull
cord around sharp edges or corners. Do not
stretch cord. Do not close doors on cord. Do not
unplug by pulling on cord. Keep cord away from
heated surfaces.
WARNING: Do Not Pick Up Flammable Or
Toxic Materials, Burning Or Smoking Debris.
WARNING: Do Not Use Flammable Liquids Or
Operate Machine In Or Near Flammable Liquids,
Vapors Or Combustible Dusts.
FIG.
4

OPERATION
6MagnaTwin t3000 (03–04)
ATTENTION: To prevent overheating, do not
operate brush motor without vacuum motor
running.
2. Pull either one or both triggers to activate brush
motor. With motor running, push machine forward
to vacuum. Revolving brush should help assist in
propelling of machine (Figure 5).
FIG.
5
3. Work away from power cord and receptacle to
prevent running over power cord. Use an “S”
pattern when cleaning.
4. When cleaning against walls or obstructions, use
right side of machine with protective roller wheel
for easier use and better edge cleaning.
HOSE ATTACHMENT OPERATION
1. Install hose by pushing onto connector, and add
desired cleaning attachment (Figure 6).
FIG.
6
2. Turn on vacuum switch and pull UP on air flow
control knob. This will direct vacuum air flow to
accessory hose connector (Figure 7).
FIG.
7
3. Return vacuum control knob to closed position
(DOWN) before resuming carpet cleaning.
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow machine’s daily, weekly and quarterly
maintenance procedures.
FOR SAFETY: Before leaving or servicing
machine, turn off machine and unplug cord from
wall outlet.
DAILY MAINTENANCE
(Every 4 Hours of Operation)
1. Check filter bag for fullness, replace or empty bag
as needed. Do not reuse paper bags. Inspect cloth
bag for tears or holes, replace if damaged. Do not
wash cloth bag.
2. Check power cord for damage. Replace if
damaged.
WARNING: Do Not Operate With Damaged
Power Cord. Do Not Modify Plug. Unplug Power
Cord Before Servicing Machine.
If the supply cord is damaged or broken, it must
be replaced by the manufacturer or it’s service
agent or a similarly qualified person in order to
avoid a hazard.
3. Turn brush adjustment knob to “STORAGE”
position and wrap power cord around handle.
4. Wipe off entire machine with damp cloth.

OPERATION
MagnaTwin t3000 (03–04) 7
WEEKLY MAINTENANCE
(Every 20 Hours of Operation)
1. Inspect intake chamber for any accumulated
debris. Clean if necessary (Figure 8).
FIG.
8
2. Tip machine back on handle and inspect brush
area for debris, string, etc. Clean if necessary.
3. Remove vacuum motor cover from bag housing to
access filters. Remove both filters from motors
and clean by tapping on a hard surface. Replace
motor filters, motor cover and filter bag; close
door (Figure 9).
FIG.
9
4. Check door seals for cuts and wear.
QUARTERLY MAINTENANCE
(Every 250 Hours of Operation)
1. Check vacuum motors for carbon brush wear,
replace brushes when worn to a length of 10mm
(0.38 in) or less.
Contact an Authorized Service Center for carbon
brush inspection.
FOR SAFETY: When servicing machine all repairs
must be performed by a qualified service person.
2. Inspect carpet brush for wear by positioning a
straight edge across shoe. If bristle extension is
3 mm (0.13 in) or less, adjust brush (Figure 10).
FIG.
10
3. Check brush drive belt for proper tension and
alignment.
4. Check vacuum bag for tears, replace if necessary.
5. Check for loose parts and tighten hardware.
6. Check rollers and wheels for wear and free
rotation. Add 3 to 4 drops of light oil in each
bearing.
ROUTINE ADJUSTMENTS
BRUSH ADJUSTMENT
FOR SAFETY: Before leaving or servicing
machine, turn off machine and unplug cord from
wall outlet.
If machine fails to pick up or propel properly, or bristles
extension from shoe is 3 mm (0.13 in) or less, brush
adjustment is required. Use following procedures:
1. Tip machine on its left side and remove eight
screws holding carpet shoe in place. Remove
shoe from lower housing (Figure 11).
FIG.
11
2. Force drive belt from brush pulley. Notice that
rubber bearing blocks have Number “1” showing
(Figure 12).

OPERATION
8MagnaTwin t3000 (03–04)
FIG.
12
3. Slide complete brush and block assembly from
lower housing, and turn rubber blocks until
Number “2” appears with arrows pointing toward
front of machine. Install brush back into housing
with Number “2” in this position. This procedure
extends brush life (Figure 12).
4. This procedure may be repeated one additional
time by rotating blocks to position “3”. After third
position is worn, brush replacement is required.
BELT ADJUSTMENT OR REPLACEMENT
FOR SAFETY: Before leaving or servicing
machine, turn off machine and unplug cord from
wall outlet.
1. Tip machine on its left side and remove three
screws holding lower access panel in place.
Remove panel from base (Figure 13).
FIG.
13
2. To check brush belt tension: Push against belt in
center with moderate force. It should deflect no
more than 6 mm (0.25 in). If adjustment is
required, loosen four screws holding motor in
place. Then use a 13 mm wrench to turn motor
adjustment nut clockwise until proper tension is
attained. Retighten screws (Figure 14).
ATTENTION: Upper housing may have to be
removed from lower housing to loosen motor
screws.
FIG. 14
3. To replace belt, follow BRUSH & BELT
ADJUSTMENT instructions. Use only original
equipment replacement parts.
STORING MACHINE
Prior to storing machine, wrap power cord around cord
hook, clean all filters and install a new vacuum bag.
Store machine in a dry area.
WARNING: Do Not Use Outdoors Or On Wet
Surfaces. Do Not Expose to Rain. Store Indoors.
RECOMMENDED STOCK ITEMS
Refer to Parts List section for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description. See example below:

OPERATION
MagnaTwin t3000 (03–04) 9
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
Machine not operating. Power cord not plugged in. Connect to power supply.
Machine not operating.
Damaged power cord. Contact Service Center.
Tripped circuit breaker in building. Reset breaker in building.
Loose or damaged internal wiring. Contact Service Center.
Brush not turning. Machine circuit bnreaker tripped. Reset breaker. Check for brush obstruc-
tion or low brush setting.
Broken belt. Replace belt.
Belt not adjusted properly. Readjust belt.
Defective brush switch. Contact Service Center.
Defective brush motor. Contact Service Center.
Poor pick–up. Filter bag full. Empty bag.
Poor pick–up.
Secondary vacuum filters dirty. Clean and replace.
Air flow lever in wrong position. Move lever to proper setting.
Brush intake area obstructed. Check for obstruction and remove.
Pick–up hose or housing plugged. Check for obstruction and remove.
Gasket leak. Replace gasket.
Brush not adjusted properly. Reset brush adjustment.
Worn brush. Adjust or replace.
Vacuum motor not
operating. Thermal overloads activated due to plug or
obstruction. Inspect and clean.
operating.
Vacuum switch defective. Contact Service Center.

OPERATION
10 MagnaTwin t3000 (03–04)
SPECIFICATIONS
MODEL Magna Twin 3000
LENGTH 1010 mm (39.75 in)
WIDTH 775 mm (30.5 in)
HEIGHT 914 mm (36 in)
WEIGHT 41.28 Kg (91 lb)
CLEANING PATH WIDTH 762 mm (30 in)
COVERAGE RATE (MAX) 4,267 m2(14,000 sq ft) per hour
VACUUM BAG 35.24 L (1 bushel)
BRUSH MOTOR .25hp, 1200 rpm, 120V, .75A, 90W
VACUUM MOTOR TWO 1 hp, 1–stage 5.7 in, 120V, 11A, 1320W
WATERLIFT AT SEALED ORIFICE 1219 mm (48 in)
DECIBEL RATING AT OPERATOR’S EAR, INDOORS ON
CARPET 74dB(A)
POWER CORD LENGTH 23 m (75 ft)

ELECTRICAL DIAGRAMS
MagnaTwin t3000 (03–04) 11
120V WIRING DIAGRAM
WHITE
GREEN
BLACK
GREEN
RED
BLACK
BLACK
WHITE
OFF
ON
BRUSH MOTOR SWITCH
VACUUM SWITCH
OFF
ON
115 VAC, 1 PHASE, 60 HZ, 15 AMP POWER
THREE WIRE CABLE TO HANDLE ASSY.
6 AMP CIRCUIT BREAKER
VACUUM MOTOR
VACUUM MOTOR
BRUSH MOTOR
BLACK

PARTS LIST
Magna Twin t3000 (03–04)
12
UPPER HOUSING GROUP
5
1
3
8
7
2
4
6
9
10
11
10
12
13
14
15
16
17
18
19
20 21
22
23
26
25
26
27
26
27
28
29
30
31
32
33
34
35
36
37
39 41
42
40
43 44
8
16
16
8
63
45
46
47
48 49 50 52
52
53
54
55
56
38
24
20
59
62
61
60
57
51
58
15

PARTS LIST
MagnaTwin t3000 (03–04) 13
UPPER HOUSING GROUP
REF PART # DESCRIPTION QTY.
1 039708249 DKNOB, CHAMBER ROD 1
2 32520 NUT, HEX JAM .25–20 1
3 573084 ROD, CHAMBER 1
4 039708134 CHAMBER, VACUUM 1
5 039708234 ROD, CHAMBER ADAPTOR 1
6 039708243 PLATE, CHAMBER ADAPTOR 1
7 200053343 SCREW, M04 X 12 MM 2
8 02850 NUT, HEX LOCK M04 X 0.7 X 17 9
9 605185 E–RING 1
10 200651019 WASHER, 8.4 MM 3
11 039708239 DGASKET, CHAMBER UPPER 1
12 039708240 DGASKET, CHAMBER LOWER 1
13 039708248 SPRING SUPPORT 1
14 200756348 SCREW, M04 X 20 MM 1
15 02850 NUT, HEX LOCK M04 X 0.7 X 17 2
16 41579 WASHER, FLAT #8 8
17 039708241 SPRING, EXT .50 X 3.0 X 0.63 1
18 039708238 DGASKET, CHAMBER 1
19 140824 SCREW, TRS .25–20 X 0.62 PHL 4
20 19066 WASHER, FLAT #10 10
21 039708052 SEAL PLATE 1
22 039708051 SEAL 1
23 200031441 SCREW, M06 X 25 MM 2
24 578728 WASHER, M6.1 LOCK 6
25 200251444 SCREW, SET M6 X 30 1
26 578244000 WASHER, M6.4 X 10 LOCK 8
27 579029 NUT, M06 X 1.0 6
28 608252 DHOSE, 3” X 23” BLACK 1
29 608253 CLAMP, HOSE 4” GEAR 2
∇039708155 ASM, VAC/GASKET 2
Y30 130988 DMOTOR, VAC FAN 2
Y31 190164 DBRUSH, CARBON
(1PK = 2 BRUSHES) 2
Y32 100122 DGASKET, VAC MOTOR 2
Y130133 TERMINAL (NOT SHOWN) 4
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
33 180626 DFRAME, FILTER, FOAM 2
34 19324 WASHER, FLAT #10 8
35 039708225 SCREW, 10–24 X 1.0 PAN PHL 8
36 700152 ASM., WIRE 14 X 7” GRN 10 X 10 2
37 140897 SCREW, GROUND 2
38 08716 SCREW, HEX M6 X 1.0 X 25 6
39 613843 CLAMP, .375 ID HALF CLIP INSUL. 1
40 579201 SCREW, M06 X 20 MM 1
41 19066 WASHER, FLAT #10 1
42 08708 NUT, HEX LOCK, M6 X 1.0 NL 1
43 039708043 PLATE, LATCH 1
44 200631346 SCREW, M04 X 16 MM 2
45 039708211 HINGE 1
46 200070340 SCREW, M04 X 8 MM PAN PHL 4
47 573086 WASHER, M4.1 X 11 9
48 200070346 SCREW, M04 X 0.7 X 17 PAN PHL 5
49 573060000 CABLE, DOOR 1
50 200452107 SCREW, #10–24 X 5/8 FIL PHL 2
51 608578 COVER, GREEN 1
52 039708060 LATCH, SWELL COVER 1
53 573068 DGASKET, DOOR OPENING 1
54 039708169 COVER, VACUUM FANS 1
55 039708244 DECAL, “WARNING VACUUM
FANS” 1
56 039708069 DBAG, VACUUM CLOTH
(STANDARD) 1
611778 DBAG, PAPER PACK OF 10
(STANDARD) 1
∇57 614132 ASM., HANDLE, GREEN 1
Y58 608484 DECAL, “MAGNA TWIN 3000” 2
Y59 573042000 DECAL, “CAUTION VAC ON” 1
Y60 613280 LABEL, WARNING AC VACUUM 1
61 573404 DECAL, ELECTRICAL 1
62 230363 SPACER, .62 X .33 X .16 1
63 579201 SCREW, M6 X 1.0 X 20 FLTPHL 5

PARTS LIST
Magna Twin t3000 (03–04)
14
LOWER HOUSING GROUP
1
2
28
4
6
7
8
10 7
10
11
17
12
13
16
18 19 20 22
5
23 24
25
26
27
33
29
30 31
32
33
34
35
36 17
37
35
38
39
40
41
42
68
44
45
46
47
48 49
50 51
52
53
54 55 56 57 58 59
60
61
62
63
64
65
66
67
69
70
72
73
74
75
76
55
77
71 15
15
60
14
74
76
3
360
43
21
9
5

PARTS LIST
MagnaTwin t3000 (03–04) 15
LOWER HOUSING GROUP
REF PART # DESCRIPTION QTY.
1 039708210 PLATE, BOTTOM COVER 1
2 363503 SCREW, PAN M6 X 1.0 X 12 1
3 140156 SPACER, .38 X .62 X 2.75 2
4 039708206 SOUND FOAM 1
5 579237 SCREW, M4 X 12 10
∇439708910 DASM, BRUSH/BEARING/PULLEY 1
Y6 069762115 SCREW, HEX 25–20 X 0.50 1
Y7 039708022 DBEARING, MOUNT 2
Y8 039708135 DASM, BRUSH W/ PINS 1
Y9 140016 WASHER, LOCK 0.25 1
Y10 140123 DBEARING, BALL 2
Y11 578416 KEY, 1/8 X 1/8 X 1/2 1
Y12 578413 DPULLEY, 1.625” DIA BRUSH 1
Y13 578261000 WASHER, .31 X .83 1
14 608185 DECAL, NOBLES LOGO 6.75” 1
15 32492 WASHER, FLAT 0.38 2
16 630508 O–RING, 9.2 ID X 12.7 1
17 039708090 DV–BELT 1
18 200301014 WASHER, FLAT 4.1 MM 6
19 039708131 DEBRIS INLET 1
20 039708201 DGASKET, DEBRIS INLET 1
21 573279 BRACKET, REINFORCING ROLLER
WELDMENT 2
22 41579 WASHER, FLAT #8 2
23 069760093 WASHER, LOCK #8 2
24 039708010 BRUSH CHAMBER 1
25 039708120 SKID 1
26 611768 SEAL, BRUSH 7” 2
27 039708025 SKID, GASKET 1
28 19066 WASHER, FLAT #10 1
29 039708026 DWHEEL, REAR 2
30 140823 SCREW, TRS 10–24 X 0.62 PHL 2
31 19324 WASHER, FLAT #10 2
32 573079 BUSHING, 3/8–16 X 12 X 25.4 DIA 2
33 039708254 SPACER, .44” X 0.75 X 0.31 NYLON 4
34 59156 NUT, HEX LOCK .38–16 NL 1
35 039708251 SCREW, SET, 8–32X1/2 SOC 2
36 578414 DPULLEY MOTOR 1
37 200031436 SCREW, M06 X 16 MM 3
38 140022 WASHER, INT 3/8 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
39 039708121 SCREW, 3/8–16 X 63.5MM 2
40 150210 CAP, PLASTIC 3/8” BLACK 2
41 573081 WASHER, CAP MOUNT 2
42 579201 SCREW, M06 X 1.0 X 20 FLAT 2
43 140053 WASHER, FLAT, .28B, .88D, .12 SS 4
∇44 573090 DASM, BRUSH MOTOR 1
Y45 605101 DMOTOR 1
Y46 573089 PIN, CLEVIS 1
Y47 573091 SCREW, .38–16 X 2.75 SPADE ZN 1
Y48 08170 PIN, COTTER .062 X 0.50 1
Y49 039708154 HARNESS, WIRE BASE 1
Y50 069762001 NUT, 1/4–20 4
51 101107 FRAME, LOWER CHARCOAL 1
52 140356 SCREW, 1/4–20 X 1” 4
53 069767136 CIRCUIT BREAKER, 7 AMP 1
54 039708064 DBEARING 2
55 578728 WASHER, M6.1 LOCK 6
56 579029 NUT, M06 5
57 039708029 ROLLER WELDMENT 1
58 039708223 NUT, 3/8–16 2
59 039708204 SCREW, 3/8–16 X 140MM 2
60 630477 DWHEEL, 2.0OD X 0.38W GRAY 4
61 573077000 KNOB, BRUSH ADJUSTMENT 1
62 039708146 DECAL, BRUSH ADJUSTMENT 1
63 039708039 SHAFT, ADJUSTMENT CAM 1
64 039708045 COLLAR, SHAFT 1
65 039708133 CAM, ADJUSTMENT PLASTIC 1
66 039708087 SPRING, TENSION 1
67 1014918 DWHEEL, RUBBER W/BUSHING 1
68 200055499 SCREW, M08 X 40 MM 1
69 140804 SCREW, RND 10–24 X 1 PHL 1
70 611768 SEAL, BRUSH 7” 2
71 140039 WASHER, FELT 1
72 140519 NUT, KEP 10–24 3
73 573083 ASM, WIRE 16 GA. GREEN 1
74 579259 SCREW, M4 X 0.7 X 12 PAN PHL 7
75 140023 WASHER 1
76 02850 NUT, HEX LOCK M4 X 0.7 7
77 069764177 EDGING, PLASTIC .037” X .222M 1

PARTS LIST
Magna Twin t3000 (03–04)
16
CONSOLE GROUP
12
3
4
10
12
13
10
19 16
18
17
5
6
7
9
8
11
20
15
14
21
22
REF PART # DESCRIPTION QTY.
1 575577 CONTROLBOX, TRIGGER 1
2 578005000 DSWITCH, ROCKER 1
3 578002000 ARM, TRIGGER CONTROLBOX 2
4 578082000 SPACER, TRIGGER 2
5 578186000 WASHER, M4.3 X 12 X 1.0 FLT 2
6 200662012 WASHER, M3 INT 2
7 069764190 SCREW, M03 X 16 MM 2
8 578008000 SCREW, M03 X 31.3 MM 3
9 140018 WASHER, LOCK INT #10 3
10 140504 NUT, CONDUIT LOCK 1/2” 2
11 130167 DSTRAIN RELIEF 1
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
12 573082 DCORD, POWER 14/3 – 75’ 1
13 573059 WIRE HARNESS, 14/4 1
14 130181 DSTRAIN RELIEF 1
15 578260000 ASM, WIRE 16 GA. BLACK 1
16 573406 DECAL, CONSOLE COVER 1
17 578011000 SCREW, #6 PANHD 2
18 578007000 TERMINAL BLOCK, 3 PIN 1
19 130712 DSWITCH, PUSH BUTTON 1
20 578430 WASHER, 0.50 SPRING DISC 1
21 140900 SCREW, 10–24 X .75 TRS PHL 1
22 140519 NUT, 10–24 KEP 3

OPTIONS
MagnaTwin t3000 (03–04) 17
WAND AND HOSE KIT
1
2
3
4
5
67
8910 11
REF PART # DESCRIPTION QTY.
∇573070 DKIT, WAND/HOSE ACCESSORIES 1
Y∇606159 DASM., HOSE 1–1/4” X 28” BLACK 1
Y1 160475 DHOSE, VAC 1–1/4” X 28” BLACK 1
Y2 160471 DCUFF, HOSE 1–1/2” TAPERED 2
Y∇610988 DKIT, STANDARD ATTACHMENT 1
Y3 190902 DCHROME HOSE ATTACHMENT 1
Y4 605587 DWAND, TELESCOPIC CHROME 1
∇ASSEMBLY
YINCLUDED IN ASSEMBLY
DRECOMMENDED STOCK ITEMS
REF PART # DESCRIPTION QTY.
Y5 605588 DTOOL, RUG & FLOOR W/WHEELS 1
Y6 190715 DTOOL, DUST BRUSH 1
Y7 190714 DTOOL, CREVICE 1
Y8 579259 SCREW, M04X12MM PAN PHL 2
Y9 200351014 WASHER, LOCK M4.1 2
Y10 140032 WASHER, #6 FLAT 2
Y11 573073 DCLIP, WAND 1” – 1–1/2” DIA 2