Noctua NH-U14S TR4-SP3 User manual

Required mounting parts:
Dear customer,
Congratulations on choosing the Noctua NH-U14S TR4-SP3.
Continuing the legacy of Noctua’s classic NH-U-series, which has
received more than a thousand awards and recommendations from
international hardware websites and magazines, the NH-U14S has
become a benchmark for high-end 140mm single tower coolers.
The TR4-SP3 version is a tailored custom model for AMD’s TR4/SP3
platform and features a larger contact surface as well as the latest
SecuFirm2™ mounting system for socket TR4/SP3.
Enjoy your NH-U14S TR4-SP3!
Yours sincerely,
Roland Mossig, Noctua CEO
This manual will guide you through the installation process of the
SecuFirm2™ mounting system step by step.
Prior to installing the cooler, please consult the compatibility list
on our website (www.noctua.at/compatibility) and verify that
the cooler is fully compatible with your motherboard.
Please also make sure that your PC case offers sufficient clear-
ance for the cooler and that there are no compatibility issues
with any other components (e.g. tall RAM modules). Double
check that the heatsink and fan clips do not make contact with
the VGA card or other PCIe cards.
Noctua cannot be held responsible for any damage or losses
caused by compatibility issues.
Should you encounter any difficulties, please check the FAQs on
our website (www.noctua.at/faqs) and don’t hesitate to contact
our support team at [e-mail].
Multilingual versions of this manual are available on our website:
www.noctua.at/manuals
Offsetting the cooler to increase PCIe clearance
If you would like to use a PCIe card in the top slot and the slot is
located close to the CPU socket on your motherboard, test fit the
cooler to the CPU socket in order to check if it comes too close
to the back side of the card or overhangs the slot. If yes, you
can offset the cooler towards the top side of the motherboard by
either 3mm or 6mm for increased PCIe clearance.
Step 1
NM-SMT3 mounting toolNM-AFB7 fastening brackets
(pre-installed on the cooler)
Noctua NH-U14S | Installation Manual | TR4-SP3
TR4-SP3
In order to offset the cooler, please unscrew the NM-AFB7 fasten-
ing brackets and re-install them in the +3 (3mm offset) or +6
(6mm offset) position.
Caution: Gently tighten the screws until they stop, but don’t use
excessive force (max. torque 0.6 Nm).
+ 0mm offset
+ 3mm offset
+ 6mm offset

Reattach the fan to the heatsink using the supplied steel clips:
Attaching the fan
Step 4
Noctua NH-U14S | Installation Manual | TR4-SP3
TR4-SP3
Then put the heatsink onto the CPU so that the four spring-loaded
screws align with the threads of the CPU socket. Use the sup-
plied mounting tool to tighten the screws. Perform 3 turns on each
screw, then repeat until all are fully tightened.
Caution: Gently tighten the screws until they stop, but don’t use
excessive force (max. torque 0.6 Nm).
Fastening the heatsink to the CPU
Please first take off the fan as well as the protection cover at the
bottom side of the heatsink.
Step 3
Note that you can tilt the mounting tool for reaching the screws in
case they are blocked by the heatsink fins.
Connect the fan to the motherboard’s CPU fan header.
Depending on your CPU and the temperature inside the case, you
may interconnect the supplied NA-RC7 Low-Noise Adapter (L.N.A.)
in order to further reduce the fan’s operating noise.
Applying thermal paste
If there are residual traces of thermal paste or thermal pads on
your CPU, please clean them off first.
Then press 9 small drops (3-4mm diameter) of NT-H1 onto the
the heatspreader in a square 3x3 pattern as shown below:
Step 2
Caution: Applying too much thermal paste will lower heat
conductivity and cooling performance!
Continue by adding 4 larger drops (5-6mm diameter) of NT-H1 in
a square pattern at the center as shown below:
1.
2.
3.

Noctua NH-U14S | Installation Manual | TR4-SP3
TR4-SP3
Even with high-grade products and strict quality control, the
possibility of defects cannot be eliminated entirely. Therefore,
we aim at providing the highest possible level of reliability and
convenience by offering a warranty period of 6 years and direct,
fast and straightforward RMA service.
Should you encounter any problems with your NH-U14S TR4-SP3,
please don’t hesitate to contact our support team (support@
noctua.at).
Please also consult the FAQ section on our website:
www.noctua.at/faqs.
Warranty, Support and FAQs
While Noctua recommends using an NF-A15 fan for best results in
dual fan mode, the extra set of fan clips can also be used to install
most other fans. In this case, please put the supplied self-adhesive
anti-vibration strips onto the heatsink to avoid vibrations being
transmitted to the cooler.
Clip position for thick pads:
Clip position for standard pads:
As it is not possible to reliably calculate or control the forces that
act upon a system during transport (e.g. in shipping), we gener-
ally recommend, for safety reasons, taking the cooler off. Noctua
cannot be held responsible for any damage that may arise due to
excessive stress during transport if you keep the heatsink installed.
Should I take the cooler off before transporting
my system?
Caution: When using the L.N.A., check the temperature of your
CPU using appropriate software (e.g. the respective applications
of your mainboard manufacturer), in order to evade automatic
throttling of the CPU due to the increased temperature. If the cool-
ing performance is insufficient, please increase case ventilation or
remove the L.N.A.
Adding a second fan
The NH-U14S TR4-SP3 includes an extra set of fan clips and an
extra set of thicker anti-vibration pads for installing a second NF-
A15 fan in push/pull mode in order to further improve cooling
performance.
Please use the thicker anti-vibration pads on the rear NF-A-15 fan
for improved acoustics if space allows. The y-cable supplied with
the retail NF-A15 fan can be used to control the speed of both fans
via the same mainboard fan header.
Please note that while the NF-A15 fan included with the NH-U14S
TR4-SP3 runs at 1500rpm, Noctua recommends using the stand-
ard 1200rpm retail version as a rear fan in push/pull mode as
the combination of 1500rpm at the front and 1200rpm at the
rear will provide the best balance of performance and acoustics.
If you would like to run both fans at the same speed, please use
the supplied Low-Noise Adaptor on the front fan to reduce the
speed to 1200rpm.
1. Remove standard pads on rear fan
2. Install thick pads on rear fan
Airflow
front fan (standard pads)
rear fan (thick pads)