Noctua NM-i4677 User manual

Take the fan(s) off the cooler. If the original mounting brackets
are already installed on the cooler, please take them off first. Then
install the NM-XFB9 brackets for LGA4677.
Dear customer,
Thank you very much for choosing a Noctua cooler for your
LGA4677 system.
This manual will guide you through the installation process step
by step using an NH-D9 DX-3647 4U heatsink as an example.
Please note that the installation procedure is identical for all
models.
Enjoy your Noctua cooler on LGA4677!
Yours sincerely,
Roland Mossig, Noctua CEO
This mounting kit for LGA4677 is compatible with Noctua DX-4189,
DX-3647 and TR4-SP3 series heatsinks. It is not compatible with
most other Noctua CPU coolers. For up-to-date cooler compatibility
information, please visit ncc.noctua.at/socket-compatibility-overview
Prior to installing the cooler, please consult the compatibility
centre on our website (ncc.noctua.at) and verify that the cooler
is fully compatible with your motherboard.
Pleasealso makesurethat your PCcaseoffers sufficientclearance for
the cooler and that there are no compatibility issues with any other
components (e.g. tall RAM modules). Double check that the
heatsink and fan clips do not make contact with the VGA
card, other PCIe cards, motherboard heatsinks or any other
components. Noctua cannot be held responsible for any damage or
losses caused by compatibility issues.
Should you encounter any difficulties, please check the FAQs on our
website (www.noctua.at/faqs) and don’t hesitate to contact our
support team at [e-mail].
NOCTUA NM-i4677
INSTALLATION MANUAL
Installing/replacing the mounting brackets1
When attaching the CPU carrier frame to the base of the heatsink,
turn the heatsink upside down so that the base is facing upwards.
Carefully put it down onto the tips of the heatpipes and secure it
with your hand so that it cannot tilt and that the fins cannot get
bent.
Remove the plastic protection cover from the base of the heatsink
and be careful not to damage the layer of pre-applied thermal
compound.
Caution: If you are not using the heatsink for the first time and
it therefore doesn’t have a fresh layer of pre-applied thermal
compound anymore, you need to apply a thin layer of thermal
compound to the CPU yourself before clipping it to the heatsink.
If there are residual traces of previous thermal paste or thermal
pads on your CPU or on the heatsink, please clean them off first.
Assembly of carrier frame, CPU and heatsink &
installation to the socket
2
Please follow the official Intel installation manual for how to
attach the CPU carrier frame to the heatsink, insert the CPU to the
carrier frame and install the CPU/heatsink assembly to the socket:
www.intel.com/processorinstall
Note that while the Intel illustrations show a 2U heatsink, the
Noctua NM-XFB9 brackets use the same mounting parts, so the
procedure is identical for Noctua heatsinks.
NOCTUA MOBILE-TAG
Reattach the fans to the heatsink using the supplied fan clips:
Installing the fans3
Caution: Gently tighten the screws until they stop, but do not use
excessive force (max. torque 0.6 Nm).
Required mounting parts:
4x NM-SSC2
short screws
2x NM-XFB9
brackets
Plastic CPU carrier frame
Please note that installing an LGA4677 processor and heatsink
requires a plastic CPU carrier frame such as the one shown
above. These carrier frames are included with boxed retail CPUs
and available separately via Intel sales partners for tray type
CPUs. As different CPUs require different carrier frame types
(E1A, E1B or E1C), please make sure to purchase the correct
carrier frame for tray type CPUs.

NOCTUA MOBILE-TAG
NOCTUA NM-i4677
INSTALLATION MANUAL
!
Even with high-grade products and strict quality control, the
possibility of defects cannot be eliminated entirely. Therefore,
we aim at providing the highest possible level of reliability and
convenience by offering a warranty period of 6 years and direct,
fast and straightforward RMA service.
Should you encounter any problems with your Noctua product,
please don’t hesitate to contact our support team at
[email protected].
Please also consult the FAQ section on our website:
www.noctua.at/faqs
Warranty, support and FAQs
As it is not possible to reliably calculate or control the forces
that act upon a system during transport (e.g. in shipping), we
generally recommend, for safety reasons, taking off coolers with
a total weight of more than 700g (incl. fan).
If the weight of the heatsink without fan is below 700g and
the total weight including fan is above 700g, we recommend
taking off the fan from the heatsink in order to reduce the weight
below 700g.
Noctua cannot be held responsible for any damage that may
arise due to excessive stress during transport if you keep the
heatsink installed.
Transporting your system!
Removing the heatsink from the socket and
the CPU from the heatsink
!
Please follow the official Intel guidelines for how to remove
the heatsink and how to take off the CPU and carrier frame:
www.intel.com/processorinstall
Connect the fans to the motherboard’s CPU fan header(s). If
necessary, use the supplied NA-YC1 y-cable to connect both
fans to one fan header.