Nokia 206 User manual

Check the repair
policy before
performing any
mechanical repair
on Service Level
1&2!
Service Manual for L1 and L2
Nokia 206 Dual SIM/2060,
Nokia 206
RM-872, RM-873
Key features
z
S40 Operating system
z
Dual SIM Easy SWAP (RM-872)
z
Big and bright screen
z
Powerful battery
z
2G Connections with background GPRS
Version 1.0
Exploded view Disassembly steps Assembly hints
Service devices Product controls and interfaces Solder components
Service concept
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.
More More More
More More More
More
All manuals and user guides at all-guides.com
all-guides.com

Service Manual Level 1 and 2
Nokia 206 Dual SIM/2060, Nokia 206
RM-872, RM-873
Version 1.0
Exploded view
LIGHT SWAP PWB
I0007
B-COVER
I0020
A-COVER
I0001
CAMERA
I0006
AV JACK
I0012
EARPIECE
I0014
DC JACK
I0013
3 IN 1 SPEAKER
I0018
KEYMAT
I0002
DOMESHEET
I0008
SIM DOOR
I0016
*Only in dual SIM variant (RM-873)
UI SHIELDING
I0004
DISPLAY
I0005
TYPE LABEL
I0011
GASKET ON SPEAKER
I0019
D-COVER
I0015
ANTENNA MODULE
I0017
BB SHIELDING LID
I0009
FEM SHIELDING LID
I0010
SCREW TORX+ SIZE 6
M1.6 x 4.5
I0003
LIGHT SWAP PACKAGE
(I0006 - I0011)
1
D-COVER ASSEMBLY
(I0012 - I0016) 2
v1.0 Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2012 Nokia | Nokia Internal Use only | All Rights Reserved.
All manuals and user guides at all-guides.com

Service Manual Level 1 and 2
Nokia 206 Dual SIM/2060, Nokia 206
RM-872, RM-873
Version 1.0
Disassembly steps
For disassembling you need the Nokia Standard toolkit version 2. You will also need an AV plug, a DC plug
and the camera removal tool SS-276.
Note that the disassembly instructions are made witht the dual SIM variant (RM-872).
Protect the A-COVER with protective film.
All manuals and user guides at all-guides.com

Release the B-COVER by using the release notch on the bottom of the device.
Remove the B-COVER.
All manuals and user guides at all-guides.com

To remove the A-COVER, first release the clips from the bottom of the device with the SRT-6.
Then release the clips from the right side by sliding the SRT-6 along the side.
All manuals and user guides at all-guides.com

Then release the clips from the left side by sliding the SRT-6 along the side.
Then release the top side.
All manuals and user guides at all-guides.com
all-guides.com

Remove the A-COVER.
Remove the KEYMAT.
All manuals and user guides at all-guides.com

Protect the DISPLAY with protective film.
Unscrew the six Torx+ size 6 screws in the order shown.
All manuals and user guides at all-guides.com

To remove the ENGINE BOARD, release the three shown clips with the SS-93.
Lift up and remove the ENGINE BOARD.
All manuals and user guides at all-guides.com

Open the DISPLAY connector with the SS-93. Be careful not to damage the connector or any
components nearby.
To remove the UI SHIELDING, release the two clips from the shown side.
All manuals and user guides at all-guides.com