Nokia 700 User manual

Service Manual for L1 and L2
Nokia 700
RM-670
Key features
New Symbian Belle software platform
3.2" nHD AMOLED screen
Tap and share with NFC technology
Personalizable home screens with different size widgets
Exploded view Disassembly steps Disassembly video
Assembly hints Service devices Solder components
Product controls and interfaces Service concept
©2011 Nokia
More More More
More More More
More More

Service Manual Level 1 and 2
Nokia 700
RM-670 Exploded view
A-COVER
I0001
EARPIECE
I0005
FLASH REFLECTOR
I0012
EARPIECE GASKET
I0004
USB BOOT
I0018
SECONDARY ANTENNA
I0015
TYPE LABEL
I0009
D-COVER
I0023
LIGHT SWAP PWB
I0008
NFC MECHANICAL ASSEMBLY
I0011
DC JACK
I0014
TEST PAD ADHESIVE
I0020
AV JACK
I0013
SCREW TORX+
SIZE 4 M1.0x3.8
I0024
BATTERY COVER
I0025
CAPTURE SWITCH
I0006
BATTERY CONNECTOR SEALING
I0019
CAMERA
I0010
MAIN ANTENNA
I0017
IHF SPEAKER
I0016
MAIN ANTENNA ASSEMBLY
(I0016, I0017)
D-COVER ASSEMBLY
(I0020 - I0023)
A-COVER ASSEMBLY
(I0001 - I0006)
SECONDARY ANTENNA ASSEMBLY
(I0013 - I0015)
LIGHT SWAP PACKAGE
(I0008, I0009)
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2011 Nokia

Service Manual Level 1 and 2
Nokia 700
RM-670 Disassembly steps
You must use the Nokia Standard Toolkit version 2. You will also need a DC plug, an AV plug and the SS-
88 camera removal tool.
Protect the A-COVER with protective film.

Use the dental tool to peel out one corner of the IHF DETAIL. Be careful not to injure yourself or damage
the A-COVER with the sharp end of the dental tool.
Remove the IHF DETAIL with the tweezers. Do not use it again. Discard it.

Open the BATTERY COVER by using the release button. Lift up and remove the BATTERY COVER.
Unscrew the six Torx+ size 4 screws in the order shown. Do not use them again. Discard them.

Press down the A-COVER from the top side with your thumb and slide the SRT-6 to direction shown to
release the right side of the A-COVER. This way the hooks holding the A-COVER will not get damaged.
Keep pressing down the A-COVER from the top side and open the top side of the A-COVER by sliding the
SRT-6 to direction shown.

Open also the left side of the A-COVER by sliding the SRT-6 towards the bottom end.
Carefully pull the A-COVER to direction shown to release the bottom end.

Lift up the right side of the A-COVER as shown. Note that the A-COVER must not be lifted up completely
to avoid damaging the flexes underneath.
Use the SS-93 to open the UI connector. Be careful not to damage the connector or any nearby
components.

Open also the DISPLAY connector with the SS-93. Be careful not to damage the connector or any nearby
components.
The A-COVER can now be separated.

Lift up the EARPIECE with the dental tool. Remove the EARPIECE with the tweezers. Do not use it again.
Discard it.
Remove also the EARPIECE GASKET with the dental tool. Do not use it again. Discard it.

Remove the CAPTURE SWITCH with the tweezers.
Use the sharp end of the SS-93 to lift up the side keys from their housing.

Use the SS-93 to lever out the ENGINE BOARD from the shown place.
Use the sharp end of the SS-93 to lever out the opposite side of the ENGINE BOARD.

Carefully lift up the ENGINE BOARD from the bottom side. Note that the ENGINE BOARD flex is attached
to the D-COVER with the TEST PAD ADHESIVE. Be careful not to damage the ENGINE BOARD.
The ENGINE BOARD can now be separated.

Remove the BATTERY CONNECTOR SEALING with the tweezers.
Pull the MAIN ANTENNA to direction shown and remove it.

If the SECONDARY ANTENNA is attached to the ENGINE BOARD with the antenna hook.
To release the SECONDARY ANTENNA push down with finger from the center and slightly lift up both
sides of the SECONDARY ANTENNA.

While holding the sides up, twist the SECONDARY ANTENNA counter-clockwise and separate it from the
ENGINE BOARD.
If the SECONDARY ANTENNA is not attached to the ENGINE BOARD with the antenna hook.

After separating the ENGINE BOARD from the D-COVER the SECONDARY ANTENNA stays in the D-COVER.
Use the sharp end of the SS-93 to lift up the SECONDARY ANTENNA from the shown place. Be careful
not to damage the shown D-COVER grounding spring under the SECONDARY ANTENNA.

Remove the SECONDARY ANTENNA with the tweezers.
Remove the USB BOOT with the tweezers.

Remove the CAMERA with the camera removal tool ss-88.
Use the SS-93 to open the NFC MECHANICAL ASSEMBLY connector. Be careful not to damage the
connector or any nearby components.

Remove the NFC MECHANICAL ASSEMBLY with the tweezers.
Remove the FLASH REFLECTOR with the tweezers.