Nokia 515 RM-953 User manual

Check the repair
policy before
performing any
mechanical repair
on Service Level
1&2!
Service Manual for L1 and L2
Nokia 515 Dual SIM
(RM-952)
Nokia 515
(RM-953)
Key features

2,4" display (320 x 240) with COrning Gorilla glass

5 Mpix camera with LED flash

Nokia Slam support

MicroSD card support up to 32 GB

Micro-USB connector
Version 1.0
Exploded view Disassembly steps Assembly hints
Solder components Service devices Product controls and interfaces
Service concept
©2013 Nokia | Nokia Internal Use only | All Rights Reserved.
More More More
More More More
More

Service Manual Level 1 and 2
Nokia 515 RM-953
Nokia 515 Dual SIM RM-952
Version 1.0
Exploded view
A-COVER
I0001
UI SHIELDING
I0005
LIGHT SWAP PWB
I0009
LED FLASH
I0019
CAMERA LENS
I0018
EARPIECE ADHESIVE
I0008
EARPIECE
I0007
CAMERA
I0014
DISPLAY
I0004
KEYMAT
I0002
DOME SHEET
I0006
SIM2 CONNECTOR
I0022
IHF SPEAKER
I0016
ANTENNA MODULE
I0015
B-COVER
I0021
RF SHIELDING LID
I0011
TYPE LABEL
I0013
FM/BT SHIELDING LID
I0012
BB SHIELDING LID
I0010
IHF SPEAKER GASKET
I0017
SCREW TORX+
SIZE 4 M1.4 X 3.8
I0003
SCREW TORX+
SIZE 4 M1.4 x 0.75-4.5
I0020
DUAL SIM VARIANT RM-952 ONLY!
LIGHT SWAP PACKAGE
(I0009 - I0013)
2
D-COVER ASSEMBLY
(I0015 - I0019)
3
UI SHIELDING ASSEMBLY
(I0005 - I0008)
1
Only available
as assembly
Not reuseable
after removal
Repair/swap
only in level 3
©2013 Nokia | Nokia Internal Use only | All Rights Reserved.

Service Manual Level 1 and 2
Nokia 515 RM-953
Nokia 515 Dual SIM RM-952
Version 1.0
Disassembly steps
1) For disassembling you need the Nokia Standard toolkit version 2. You will also need the camera
removal tool SS-276 and the SIM door key.
2) Protect the A-COVER with protective film.

3) Push the SIM door key to the shown hole in the bottom end of the device to release the B-COVER.
4) Use the SRT-6 to release the bottom end of the B-COVER completely.

5) Lift up the bottom end of the B-COVER and remove it.
6) Lift up the BATTERY from the shown place and remove it.

7) Unscrew the two shown Torx+ size 4 screws in the order shown.
8) Start to relase the A-COVER by opening the shown clip on the bottom end of the device with the SRT-
6.

9) Open the five clips on the left side of the device holding the A-COVER with the SRT-6.
10) Release also the five clips on the right side of the device with the SRT-6. The A-COVER can then be
separated.

11) Protect the DISPLAY with protective film.
12) Protect also the other side of the A-COVER window with the protective film.

13) Push in the two shown clips holding the KEYMAT with the SS-93. Then carefully push the KEYMAT to
the direction shown and remove it.
14) Unscrew the four shown Torx+ size 4 screws in the order shown.

15) Open the two shown clips holding the D-COVER with the SRT-6.
16) The D-COVER can now be separated.