Nolan N-Com R Series Installation instructions

US

EN
MCS III
MCS III - 03/12/2019
SAFETY AND INSTRUCTIONS FOR USE
Congratulations on your purchase of an N-Com product.
The N-Com MCS III was built adopting the latest technologies and the best materials. Long
tests and thorough system development have made it possible to achieve the highest
sound quality.
The MCS III system can only be assembled on Nolan helmets pre-set for N-Com.
The MCS III system allows you to listen to audio devices installed on the motorcycles; it
CANNOT be used in conjunction with other audio systems for helmets.
For additional information about MCS III and to download high-definition instructions, visit
the website www.n-com.it

Table of contents
1. WARNINGS AND SAFETY.................................................................................................4
2. CONTENTS OF THE PACKAGING....................................................................................6
3. INSTALLATION....................................................................................................................7
4. OPERATION OF THE MCS III SYSTEM..........................................................................14
5. MAINTENANCE.................................................................................................................14
6. LIMITED WARRANTY.......................................................................................................15

EN
4
1. WARNINGS AND SAFETY
Read this User Manual carefully, as well as the simple rules listed below. Failure to comply with these rules may lead
to dangerous situations.
Caution: The product cannot be used in official or non-official competitions, motordromes, circuits, racing tracks and
the like.
Caution: Installation of the N-Com MCS III system results in a weight increase of approximately 80g, which is added
to the weight of the helmet and of the other accessories.
Warning: The electronic components of the N-Com system mounted inside the helmet are not waterproof.
Consequently, make sure the inside of the helmet, including the comfort padding, does not get wet in order to
avoid damage to the system. If it does, remove the N-Com system and the helmet comfort padding and let it air
dry. Remove the battery from its housing and let it dry.
Warning: Helmet speakers may not be legal in all jurisdictions. Check your local laws BEFORE using this product.
1.1. Reference standards
The MCS III product of the N-Com line complies with Directive 2014/30/EU
1.2. Road safety
Always obey all Traffic Regulations in force. While riding the motorcycle, your hands should always be engaged in
actually riding the vehicle. Any operation to the N-Com system must be carried out with the vehicle stopped.
In all cases, obey the Traffic Regulations and remember that riding the motorcycle has absolute priority over any
other manoeuvre.
1.3. Interferences
All phones and devices with wireless signal transmission are subject to interferences that may affect the performance
of the device connected to them. These interferences are not ascribable to a defect of the N-Com system.
1.4. Appropriate use
Use the device only in the normal position, as described in the product documentation. Do not attempt to
disassemble, tamper with or modify any part of the N-Com system.
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it before
you use the system on the road.
Caution: Adjusting the volume to very high levels may cause damage to your hearing.

MCS III
5
Caution: Adjust the volume of the N-Com system (where provided) and of the audio sources connected to it so as to
avoid audio reproduction at high volumes. Constant exposure to high audio volumes may damage your hearing.
Caution: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of
the helmet itself, thus creating dangerous conditions. Install the N-Com system according to the instructions
provided in the product documentation. In case of doubt, please contact your local N-Com dealer.
1.5. Qualified personnel
Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always turn to
your local dealer.
The helmet is a safety device. Tampering with it and/or with the electronic system inside the helmet, in addition to
invalidating the product warranty, can also lead to dangerous situations.
1.6. Disposal
Refer to this user manual and to manuals related to other parts of the N-Com system in order to disassemble the
system from the helmet. Once the system has been disassembled, dispose of it according to the following
instructions:
The presence of a crossed-out wheelie bin indicates that in the European Union the product is
subject to separate collection at the end of its useful life.
Do not dispose of these products together with undifferentiated urban waste.
The proper disposal of obsolete equipment contributes to preventing possible negative consequences on
people’s health and on the environment.
For more detailed information on the disposal of obsolete equipment, contact your municipality, a waste
disposal service or the store where the product was purchased.

EN
6
2. CONTENTS OF THE PACKAGING
The N-Com MCS III package contains:
MCS III
system
Honda Goldwing
connection cable
Harley Davidson
connection cable
Key
Adhesive strips for loudspeakers
Microphone with clip

MCS III
7
3. INSTALLATION
Important: Prior to installing the N-Com system, it is recommended to write down the identification
code affixed to the product (see chapter 6.5).
Remove the cheek padding (see helmet instructions).
Remove the helmet edge gasket using the special tool (Fig. 1).
Completely remove the gasket as shown in Fig. 1; by doing so you also remove the padding.
Remove the “N-Com” plugs found at the back of the shell gasket and on the left side of the
helmet.
Fig. 1 Fig. 1 – ONLY FOR N100-5 AND N87 HELMETS
Prior to installing the N-Com system, remove any filling foam material found in the helmet.
Option 1 Option 2
N.B.: Keep the filling
material in case you wish to
use the helmet without the
N-Com system in the
future.

EN
8
3.1. Installing the MCS III system on the helmet
Fig. 2
Hook up the microphone connector to the
other end, following the directions of the
arrows (Fig. 2).
N.B.: You can adjust the position of the
microphone. For instructions on how to do this,
please see chapter. 3.2.
Fig. 3
Place the system in the special housing in
the back of the helmet, pushing it all the
way into the groove (Fig. 3).

MCS III
9
Fig. 4
N.B.: For positioning of the wiring and of the
microphone in the N100-5 helmet, follow the
instructions provided in the dedicated box.
Fix the cable inside the helmet and make
sure the right fixing clip snaps into its
housing (Fig. 4).
Fig. 5
Position the microphone in the housing on
the right of the helmet, inserting the metal
boom in the groove found in the chin guard
coupling frame (Fig. 5).
Caution: make sure that the side of the
microphone support with the writing “N-
Com” is facing inward.
Fix the cable inside the helmet and make sure the left fixing clip snaps into its housing.

EN
10
ONLY FOR HELMET N100-5 – positioning of wiring and microphone
Positioning the right side wiring and the microphone:
Lift up the plastic lining of the cheek padding (Fig. 6).
Insert the microphone into the eyelet (Fig. 7) and position it in the special housing, then inserting the
metal boom in the groove found in the chin guard coupling frame (Fig. 8).
Caution: make sure that the side of the microphone support with the writing “N-Com” is facing inward.
Fix the cable inside the helmet and make sure the right fixing clip snaps into its housing (Fig. 9).
Reposition the plastic lining of the cheek padding, arranging it behind the two small stop hooks (Fig.
10).
Fig. 6
Fig. 7 Fig. 8
Fig. 9
Fig. 10

MCS III
11
ONLY FOR HELMET N100-5 – positioning of wiring and microphone
Positioning the left side wiring:
Lift up the plastic lining of the cheek padding (Fig. 11).
Fix the cable inside the helmet and make sure the left fixing clip snaps into its housing (Fig. 12).
Reposition the plastic lining of the cheek padding, arranging it behind the two small stop hooks (Fig.
13).
Fig. 11 Fig. 12 Fig. 13
Check that the connectors of the microphone and loudspeakers are correctly plugged in.
Position the left and right speakers in the respective housing obtained in the polystyrene cheek
padding. If necessary, rotate the speakers slightly in their housing. If necessary, secure them using
the adhesive strips supplied as standard equipment.
Fig. 14
Reassemble the gasket and secure it with the
specific screw, making sure that the cable
connecting to the motorbike comes out of
the helmet as shown in Fig. 14.
Reassemble the cheek padding.

EN
12
3.2. Adjusting the microphone
The MCS III system makes it possible to adjust the position of the microphone in order to facilitate its
positioning in the different helmet models. Proceed as follows:
Open the clip positioned on the microphone boom, operating as indicated in Fig. 15.
Adjust the microphone (Fig. 16).
Close the clip (Fig. 17).
Fig. 15 Fig. 16 Fig. 17
To ensure good voice transmission quality, it is recommended to position the microphone sponge at
the side of your mouth.

MCS III
13
3.3. Removing the MCS III system from the helmet
Proceed as follows to remove the MCS III system from the helmet:
Remove the cheek padding and the shell gasket.
Unhook the right and the left clips from the shell, levering upward using a flat head screw (or a
similar tool), as shown in figure 18.
Completely remove the MCS III system from helmet using a flat head screwdriver (or similar tool)
and re-install the cheek padding and the edge gasket.
Fig. 18
Fig. 19

EN
14
4. OPERATION OF THE MCS III SYSTEM
Hook up the cable to the motorcycle, then to the MCS III system. The audio of the system installed on
the motorcycle is now transferred to the helmet.
You can use the interphone system on the motorcycle by connecting both the pilot’s helmet and the
passenger’s to the motorcycle. Each helmet must be equipped with the MCS III system.
Volume levels of the radio and of intercom have to be set from the motorbike’s audio system, as
desired.
When using the INTERCOM function, the volume has to be set at a comfortable level for conversation.
Do not increase the volume too much to avoid background interference.
For all audio settings and adjustments, please read your motorbike manual.
Warning: Connect the cables so that they are free and do not hinder riding nor reduce the freedom of
movement, and do not wind them around the limbs, bust or neck. Do not lock the connectors so
that, if necessary, they can be easily disconnected.
Fig. 20
Attention: do not pull the cable. Do not use the
cable to lift the helmet. Do not pull the cable to
separate the two connectors. To separate the
connectors, hold them and pull them in opposite
directions.
5. MAINTENANCE
The N-Com does not require any special maintenance tasks. In case you use the kit when it rains, dry
off the wet parts of the helmet.

MCS III
15
6. LIMITED WARRANTY
Limited warranty certificate valid for 2 (two) years from the date of purchase.
Dear Customer,
Thank you for choosing a Nolangroup N-Com device.
PLEASE READ CAREFULLY ALL THE CLAUSES AND CONDITIONS OF THIS LIMITED WARRANTY CERTIFICATE.
By this LIMITED WARRANTY CERTIFICATE, Nolangroup guarantee to the original purchaser of the N-Com that the
product is free from all material and manufacturing defects at the time of purchase.
COVER PROVIDED BY THE WARRANTY
If any defect covered by this limited warranty certificate comes to light within 2 (two) years from the date of purchase,
Nolangroup shall proceed, through their distribution networks and after verifying the defect, to repair or replace the
defective product. Nolangroup shall supply all the materials and provide all the labor reasonably necessary to remedy
the reported defect, except for cases in which the damage is attributable to one of the reasons listed in the paragraph
below, entitled “Exclusions and limitations of cover”.
EXCLUSIONS AND LIMITATIONS OF COVER
This warranty covers only material and manufacturing defects. Nolangroup cannot be held liable for damages to the
product which are either wholly or partially attributable to any other cause, including, but not limited to:
Damage caused by improper use, lack of due care, normal wear and tear of internal and external components.
Scratches, abrasions, or other damage caused to the external parts of the N-Com by accidental impacts.
Damage caused by the application of stickers and/or adhesives.
Any damage caused by an accident.
Any modification or change made to the device by the user or by third parties.
Use of incompatible accessories not sold by Nolangroup.
Defects covered by this warranty likewise do not include all the specific and subjective situations which may arise
during dynamic use of the N-Com equipped helmet, such as problems of comfort due to improper sizing, or wind
noise while riding. Nolangroup cannot in any case be held liable for accidental or consequential damage (including,
with no limitation whatsoever, injuries to a person or persons) resulting from the failure to comply with the
obligations stipulated in this warranty regarding Nolangroup products.
Some states do not allow the exclusion or limitation of implied warranties, incidental or consequential damages, so
the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state

EN
16
VALIDITY OF THIS LIMITED WARRANTY
This warranty is valid only if all the sections of the attached REGISTRATION FORM are completed in full and the
registration is returned to the address indicated on the card within 10 (ten) days from the date of purchase:
Identification code
Name of the authorized dealer
Date of purchase of the N-Com
Name, address and telephone number of the purchaser
PROCEDURE TO BE FOLLOWED TO MAKE POSSIBLE CLAIMS
To proceed with any claim covered by this warranty, the purchaser must notify directly Nolangroup’s agent in the
USA of the alleged defect encountered by him. In agreement with Nolangroup’s agent, the purchaser may have to
return the device to which complains refer, at the purchaser’s expense, along with the sales receipt or other proof of
purchase (and date of purchase) and a copy of the warranty registration form.
BEFORE REFERRING THE MATTER TO THE AGENT, WE ADVISE YOU TO READ CAREFULLY THE USER’ MANUAL
INCLUDED WITH THE DEVICE WHICH MUST BE FOLLOWED SCRUPULOUSLY FOR YOUR OWN PROTECTION AND
THAT OF THIRD PARTIES.
2 (TWO) YEARS AFTER THE DATE OF PURCHASE THIS LIMITED WARRANTY SHALL LAPSE ENTIRELY.
This warranty is valid in the entire territory of the United States and Canada is the only express warranty given by
Nolangroup in relation to the sales of their own devices.
Any service provided under the warranty does not have the effect of extending the warranty period itself. If any
device or any of its components are replaced a new warranty period does not begin to run on the product or on
individual components supplied by the way of replacement; the date of purchase of the original device remains the
deciding factor.
For further information, please contact the following address or telephone numbers:
USA
CIMA INTERNATIONAL
1585 Beverly court #118
Aurora IL 60502
Ph: [phone]
Fax: [phone]
E-mail: [e-mail]
Toll-free (USA only): 866-243-5638

REGISTRATION FORM
DEVICE INFORMATION
Serial Number (as printed on the bo
x)
Designation of the model
DEALER INFORMATION
Name of the authorized dealer
Address
PURCHASE INFORMATION
Date of purchase of the device
PURCHASER INFORMATION
Name of the purchaser
Address
Telephone Number
E
-
mail a
ddress
OTHER INFORMATION
How did you hear about this model of Nolangroup N-Com™?
What do you mainly use your N
-
Com for (communication, music, phone, GPS,etc..)?
What brand and model of motorcycle do you ride?
What is your favourite motor
cycle magazine?

ES
MCS III
MCS III - 03/12/2019
SEGURIDAD E INSTRUCCIONES
Felicitaciones por haber comprado un producto N-Com.
N-Com MCS III ha sido fabricado utilizando las tecnologías más modernas y con los
mejores materiales. Los tests prolongados y el desarrollo exhaustivo del sistema han
permitido alcanzar la más elevada calidad en el audio.
MCS III se puede montar sólamente sobre cascos Nolan predispuestos para N-Com.
El sistema MCS III permite escuchar los dispositivos audio de la moto y NO puede ser
utilizado en combinación con otros sistemas audio para cascos.
Para más información acerca del MCS III, para descargar las instrucciones en alta definición,
visite nuestro sitio internet www.n-com.it
Sumario
1. ADVERTENCIAS Y SEGURIDAD......................................................................................20
2. CONTENIDO DE LA CONFECCIÓN...............................................................................22
3. INSTALACIÓN ...................................................................................................................23
4. FUNCIONAMIENTO DEL SISTEMA MCS III..................................................................30
5. MANTENIMIENTO............................................................................................................30
6. GARANTÍA LIMITADA......................................................................................................31

ES
20
1. ADVERTENCIAS Y SEGURIDAD
Lea detenidamente el presente folleto de instrucciones. Lea las normas mencionadas a continuación. El
incumplimiento de dichas normas podría causar situaciones de peligro.
Atención: el producto no se puede utilizar en competiciones oficiales ni extra oficiales, motódromos, circuitos, pistas
y otros casos.
Atención: la instalación del sistema N-Com MCS III comporta un incremento de peso de alrededor de 80g que se
suma al peso del casco y de los otros accesorios.
Advertencia: las partes electrónicas del sistema N-Com dentro del casco no son impermeables. Por lo tanto, hay que
evitar que se moje el interior del mismo, incluyendo el acolchado de confort, para no causar daños al sistema. Si el
agua se enfiltrara dentro del casco, extraer el sistema N-Com y el relleno de confort del interior del casco y ponerlo
a secar. Sacar la batería del compartimiento y dejar que se seque.
Advertencia: El uso de un intercomunicador para cascos podría ser ilegal en algunos países. Informarse acerca de las
leyes locales ANTES de utilizar el producto.
1.1. Referencias normativas
El producto MCS III de la línea N-Com está conforme con la directiva 2014/30/EU
1.2. Seguridad vial
Respetar todas las leyes vigentes que regulan la circulación vial. Durante la conducción del vehículo, las manos deben
usarse sólo para conducir. Todas las operaciones que se deban hacer con el sistema N-Com deben ser con el vehículo
detenido.
En cualquier caso, el respeto de la ley y la conducción de la motocicleta tienen prioridad absoluta.
1.3. Interferencias
Todos los teléfonos y los mecanismos con transmisión de señal inalámbrica están expuestos a interferencias que
pueden influir en las ejecuciones del aparato al que están conectados. Dichas interferencias no deben ser
consideradas un defecto del sistema N-Com.
1.4. Uso adecuado
Utilizar el dispositivo sólo en la posición normal, como aparece descrito en los documentos del producto. No
desmontar, ni forzar o modificar ninguna parte del sistema N-Com.