NordicTrack GX2 Sport NTEX03009.3 User manual

USERʼS MANUAL
Serial Number Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. eep this manual
for future reference.
Model No. NTEX03009.3
Serial No.
Write the serial number in the
space above for reference.
www.iconeurope.com
QUESTIONS?
If you have questions, or if there are
missing parts, please contact us:
Call: 08457 089 009
From Ireland: 053 92 36102
Website: www.iconsupport.eu
Write:
ICON Health & Fitness, Ltd.
c/o HI Group PLC
Express Way
Whitwood, West Yorkshire
WF10 5QJ
U

2
TABLE OF CONTENTS
WARNINGDECALPLACE ENT ..............................................................2
I PORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSE BLY ...............................................................................5
HOWTOUSETHEEXERCISECYCLE ........................................................9
PARTLIST ..............................................................................10
EXPLODEDDRAWING.....................................................................11
ORDERINGREPLACE ENTPARTS ..................................................BackCover
NordicTrack is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this manual
and request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Use the exercise cycle only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
4. The exercise cycle is intended for home use
only. Do not use the exercise cycle in a com-
mercial, rental, or institutional setting.
5. eep the exercise cycle indoors, away from
moisture and dust. Place the exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 2 ft. (0.6 m) of clearance
around the exercise cycle.
6. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
7. eep children under age 12 and pets away
from the exercise cycle at all times.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes for foot protection.
9. The exercise cycle should not be used by
persons weighing more than 250 lbs.
(113 kg).
10. Always keep your back straight while using
the exercise cycle; do not arch your back.
11. The exercise cycle does not have a free-
wheel; the pedals will continue to move until
the flywheel stops. Reduce your pedaling
speed in a controlled way.
12. To stop the flywheel quickly, press the brake
lever downward.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
IMPORTANT PRECAUTIONS

4
Thank you for selecting the new NordicTrack®GX2
SPORT exercise cycle. Cycling is an effective exercise
for increasing cardiovascular fitness, building
endurance, and toning the body. The GX2 SPORT
exercise cycle provides a selection of features
designed to make your workouts at home more effec-
tive and enjoyable.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Resistance Knob
Brake Lever
Seat
Adjustment Knobs
Adjustment Knob
Pedal/Strap
Water Bottle Holder
Leveling Foot
Handlebar
BEFORE YOU BEGIN
Wheel
Leveling Foot

5
ASSEMBLY
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires an adjustable wrench and a Phillips
screwdriver .
Note: If a part is not in the hardware kit, check to see if it has been preattached.
1. Remove the two screws (not shown), the two
washers (not shown), and the shipping bracket
(not shown) from the rear of the Frame (1).
Discard the screws, washers, and shipping
bracket.
Identify the Rear Stabilizer (7), which does not
have wheels.
Tighten two Leveling Feet (16) and two 10
Hex Nuts (49) into the underside of the Rear
Stabilizer (7).
Attach the Rear Stabilizer (7) to the Frame (1)
with two 10 x 25mm Screws (34) and two
10 Washers (33).
2. Remove the two screws (not shown), the two
washers (not shown), and the shipping bracket
(not shown) from the front of the Frame (1).
Discard the screws, washers, and shipping
bracket.
Orient the Front Stabilizer (8) as shown.
Attach the Front Stabilizer (8) to the Frame (1)
with two 10 x 25mm Screws (34) and two
10 Washers (33).
1
34
33
49
49
16
7
1
1
8
16
34
33
21
21
34
33
2

6
4. Orient the Handlebar Post (4) as shown.
Locate the Adjustment Knob (23) on the front of
the Frame (1). Loosen the Adjustment Knob,
pull it outward, and insert the Handlebar Post
(4) into the Frame.
Next, move the Handlebar Post (4) upward or
downward to the desired position, release the
Adjustment Knob (23) into an adjustment hole
in the Handlebar Post, and then tighten the
Adjustment Knob.
Move the Handlebar Post (4) upward or
downward slightly to make sure that the
Adjustment nob (23) is firmly engaged in
an adjustment hole in the Handlebar Post.
3
4
3. Identify the Right Pedal (35), which is marked
with an “R.”
Using an adjustable wrench, firmly tighten the
Right Pedal (35) clockwise into the Right Crank
Arm (31).
Tighten the Left Pedal (61) counterclockwise
into the Left Crank Arm (not shown).
IMPORTANT: Tighten both Pedals (35, 61) as
firmly as possible. After using the exercise
cycle for one week, retighten the Pedals.
61
35
4
23
1
31

7
5. Attach the Handlebar (5) to the Handlebar Post
(4) with two 10 x 25mm Screws (34) and two
10 Washers (33).
5
6
6. Orient the Seat Post (2) as shown.
Locate the Adjustment Knob (23) on the rear of
the Frame (1). Loosen the Adjustment Knob,
pull it outward, and insert the Seat Post (2) into
the Frame.
Next, move the Seat Post (2) upward or down-
ward to the desired position, release the
Adjustment Knob (23) into an adjustment hole
in the Seat Post, and then tighten the
Adjustment Knob.
Move the Seat Post (2) upward or downward
slightly to make sure that the Adjustment
nob (23) is firmly engaged in an adjust-
ment hole in the Seat Post.
4
2
1
23
5
34
33

8
7
3
2
1
23
22
7. Orient the Seat (22) and the Seat Carriage (3)
as shown.
See the inset drawing. Attach the Seat (22) to
the Seat Carriage (3) with two 8 Hex Nuts
(66). Make sure that the nose of the Seat is
pointing straight ahead before you tighten
the Hex Nuts.
Locate the Adjustment Knob (23) on the Seat
Post (2). Loosen the Adjustment Knob, pull it
downward, and insert the Seat Carriage (3) into
the Seat Post.
Slide the Seat Carriage (3) to the desired posi-
tion, release the Adjustment Knob (23) into an
adjustment hole in the Seat Carriage, and then
tighten the Adjustment Knob. Make sure that
the Adjustment nob is firmly engaged in an
adjustment hole in the Seat Carriage.
8. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly
is completed, some extra parts may be left over. Place a mat beneath the exercise cycle to protect the floor.
66
22
3

9
HOW TO USE THE EXERCISE CYCLE
HOW TO ADJUST THE SEAT
To adjust the position
of the seat, first loosen
the adjustment knob
and pull the adjustment
knob downward. Next,
move the seat forward
or backward to the
desired position. Then,
release the adjustment
knob into an adjust-
ment hole in the seat carriage and firmly tighten the
adjustment knob. Make sure that the adjustment
knob is engaged in an adjustment hole.
HOW TO ADJUST THE SEAT POST
For effective exercise, the seat should be at the
proper height. As you pedal, there should be a slight
bend in your knees when the pedals are in the lowest
position.
To adjust the height of
the seat post, first
loosen the adjustment
knob and pull the
adjustment knob out-
ward. Next, raise or
lower the seat post to
the desired position.
Then, release the
adjustment knob into
an adjustment hole in
the seat post and tighten the adjustment knob. Make
sure that the adjustment knob is engaged in an
adjustment hole.
HOW TO ADJUST THE HANDLEBAR POST
To adjust the height of
the handlebar post,
first loosen the adjust-
ment knob and pull the
adjustment knob out-
ward. Next, raise or
lower the handlebar
post to the desired
position. Then, release
the adjustment knob
into an adjustment hole in the handlebar post and
tighten the adjustment knob. Make sure that the
adjustment knob is engaged in an adjustment
hole.
HOW TO ADJUST THE PEDAL STRAPS
To tighten the pedal straps, simply pull the ends of the
pedal straps. To loosen the pedal straps, press and
hold the tabs on the buckles, adjust the pedal straps
to the desired position, and then release the tabs.
HOW TO ADJUST THE PEDALING RESISTANCE
To increase the resis-
tance of the pedals,
turn the resistance
knob clockwise; to
decrease the resis-
tance, turn the
resistance knob coun-
terclockwise.
To stop the flywheel,
push the brake lever
downward. The fly-
wheel should quickly
come to a complete
stop.
HOW TO LEVEL THE EXERCISE CYCLE
If the exercise cycle
rocks slightly on your
floor during use, turn
one or both of the level-
ing feet on the front or
rear stabilizer until the
rocking motion is elimi-
nated.
HOW TO MAINTAIN THE EXERCISE CYCLE
Inspect and tighten all parts of the exercise cycle reg-
ularly. Replace any worn parts immediately.
To clean the exercise cycle, use a damp cloth and a
small amount of mild detergent. IMPORTANT: To
avoid damage to the console, keep liquids away
from the console and keep the console out of
direct sunlight.
Seat
Adjustment
Knob
Adjustment
Knob
Resistance
Knob
Leveling
Feet
Seat
Post
Handlebar
Post
Brake
Lever
Adjustment
Knob

10
11 Frame
21Seat Post
31Seat Carriage
41Handlebar Post
51Handlebar
62 12 Acorn Nut
71Rear Stabilizer
81Front Stabilizer
91Brake Lever
10 1 Felt Washer
11 1 Resistance Knob
12 1 Left Crank Arm
13 7 Self-tapping Screw
14 1 Right Shield
15 1 Left Shield
16 4 Leveling Foot
17 2 Seat Post Bushing
18 4 Stabilizer Cap
19 3 Post Cap
20 1 Shield Cover
21 2 Wheel
22 1 Seat
23 3 Adjustment Knob
24 1 Brake Cap
25 1 Frame Cap
26 2 6.5mm Plastic Spacer
27 5 T1 Nut
28 1 Chain
29 2 Bracket Washer
30 1 Crank Axle
31 1 Right Crank Arm/Crank Wheel
32 2 Crank Cap
33 6 10 Washer
34 6 10 x 25mm Screw
35 1 Right Pedal/Strap
36 1 Flywheel
37 1 Flywheel Axle
38 2 Flywheel Bracket
39 1 Sleeve
40 2 8 Locknut
41 2 Brake Pad
42 1 Brake Clamp
43 1 Small Knob Washer
44 2 Flywheel Bearing
45 2 Crank Bearing
46 4 Wheel Bearing
47 1 Flywheel Sprocket
48 2 Snap Ring
49 4 10 Hex Nut
50 3 Wheel Bolt Set
51 1 6 x 40mm Bolt
52 4 5 Washer
53 2 Crank Nut
54 2 5 x 25mm Screw
55 3 12 Thin Hex Nut
56 1 6 Flange Nut
57 2 Spanner Nut
58 1 10 Locknut
59 2 5 x 12mm Screw
60 1 Water Bottle Holder
61 1 Left Pedal/Strap
62 2 5 x 12mm Screw
63 2 Brake Cable
64 1 Caliper Brake
65 2 Brake Pad ount
66 2 8 Hex Nut
67 1 Handlebar Post Bushing
*–Assembly Tool
*–Userʼs anual
ey No. Qty. Description ey No. Qty. Description
PART LIST—Model No. NTEX03009.3 R0510A
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.

11
EXPLODED DRAWING—Model No. NTEX03009.3 R0510A
19
17
2
22
3
23
19
34
33 33
4
19
5
67
50
11
43
10
9
50
42
62
23
60
52
63
58
17
23
12
53 32
61
61
56 24
25
64
51
41
65
34
33
34
33
1
18
50
50
46
21
46
49
16
46
50
21
46
50 49
16
18
8
49
16
18
7
6
29
40
38
55
39
44
44
36
31
47
28
57
37
55
38
40
29
6
20
27
13
52
59
13
14
13
13
35
35
35
32 53
48
30
45
27
26
15
54
27
18
49
16
45
52
48
66
66

Part No. 299011 R0510A Printed in China © 2010 ICON IP, Inc.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)