Nordpeis Brussel FP-BRO01-201 User manual

GB Installation manual 2
Art.no: FP-BRO01-201
28.09.2010
Brüssel

2 GB
NB! See separate instructions for the insert
General information
Our surrounds are all made of non-combustible
materials. All our inserts/stoves are tested
according to the latest European requirements
and also to the Norwegian SINTEF standard, which
includes particle tests. Several European countries
however have individual rules for installation of
inserts, stoves and replaces. You as a client are
totally responsible for the fullling of these local
rules concerning the installation in your region/
country. Nordpeis (Northstar) is not responsible
regarding correct installation.
You should check local regulations concerning:
• distance from rebox to combustible/ammable
materials
• insulation materials/requirements between
replace surround and back wall
• size of oor plates in front of replace/stove if
required
• uepipe connection between rebox and chimney
• insulation requirements if uepipe goes through
ammable wall such as a wood wall.
Adjustment
We recommend to stack the surround without glue in
order to adjust the insert prior to perforating the chimney
for the ue connection. Use a spirit level to ensure that
the surround is mounted straight. The insert will expand
with heat and for this reason the surround must not rest
on the insert. (Above the insert there must be a gap
of 3 to 5 mm. Laterally there is no need for gaps, but
between the lower part of the insert and the surround
there must be a gap of at least 2 mm.)
Floor plate
A reproof oor plate must be put in front of the replace
if the oor is of a combustible material.
Powder glue for lling
This is used to repair any notches or wounds in the
concrete. Mix the provided powder glue with water
(the consistency of the glue should be that of tooth
paste). Before you start, use a damp sponge to wet the
concrete surface. This will remove dust and provide for
better adhesion. Fill in any uneven surfaces.
Acrylic glue
This is used for gluing the elements towards wall, gluing
the elements together and for lling joints.
Painting
The surround can be painted 24hrs after that it has
been assembled. Any surface that has been lled needs
to be smoothened with ne sand paper. Use latex or
acrylic based paint (emulsion paint).
Marble/granite
Clean the plates with mild soapy water and remove any
remaining glue.
Fine Fissures
Settlement cracks can appear during the rst year of
new built houses. For this reason, very thin ssures
could appear in the joints between the elements, the
rewall and the chimney. This is entirely normal and
no reason for concern. These small ssures can be
removed by renewing the joint. Scrape out the joint with
a joint scraper and then vacuum clean to remove all the
dirt. Inject acrylic into the joint and even out by using
the ngertip with some soapy water. After about 24
hours the joint can be repainted.
Smaller damages
These are successfully repaired with the provided
powder glue. If the damage is deep, we recommend
lling twice in order to avoid sinking. Fill smaller cracks
and uneven surfaces with a oat or a brush. Smoothen
the surface with a damp sponge or sand paper.
For your own safety, comply with the assembly
instructions. All safety distances are minimum distances.
Installation of the insert must comply with the rules and
regulations of the country where installed. Nordpeis AS
is not responsible for wrongly assembled inserts.
We accept no liability for typographical errors and
changes.

3
GB
Weight with insert
Brüssel 321 kg
Brüssel High 426 kg
Assembly instructions (FIG 2 - FIG 15)
FIG 2: Place the bottom plate in 90º relative to the
chimney/wall. If needed, adjust with wedges or powder
glue.
FIG 5: Make sure there is a gap between the insert and
the surround as the insert expand with heat. Also read
the section about adjustment.
FIG 11: Brussels High is achieved by adding 2
additional elements. First cover the top grate with 50
mm non-ammable insulation and cut holes for air-
outlet in the laterals. The openings on each side must
be at least 28 x 28 cm with a grate that has 50% air
opening. (Minimum total air-outlet needs to be 770
cm2.) When mounting the replace laterally towards the
chimney, place both grates on the same side to ensure
enough air outlet.
FIG 14 / FIG 15: Close the laterals of the insert with
an additional element in case the replace is mounted
laterally towards the chimney or the insert has only front
glas.
Brüssel

4
Brüssel & Brüssel høy / Brüssel high
= mm
570
820
1850
800
570
820
800
2385

5
FIG 3FIG 2
FIG 5
1
+/- 515 mm
2
FIG 4
90°
2
34
5
6
7
3 mm

6
3
FIG 8
4
FIG 6 FIG 7
2 mm
FIG 9
89
12
13
10
11
3 mm

7
FIG 10
1
2
FIG Z
15
FIG 11 FIG 12
Vinkelsliper
min. 28 x 28 cm
16 17
BRÜSSEL HIGH
14

8
FIG 14 FIG 15
FIG 13
1
2
FIG Z
18
19