Nordson Pro-P2 User manual

Pro-P2
Fingerprint Standalone Access Control
User Manual

Content
1 Overview.....................................................................................................................................................4
1.1 Introduction.........................................................................................................................................4
1.2 Function features...............................................................................................................................4
1.3 Functional unit....................................................................................................................................4
1.4 Technical parameters..................................................................................................................... 5
2 Installation, wiring and debugging..........................................................................................................5
2.1 Packing list..........................................................................................................................................5
2.2 Installation and Wiring.......................................................................................................................6
2.3 Debugging..........................................................................................................................................7
3 Getting Started.........................................................................................................................................7
3.1 Enter management menu operation mode...................................................................................8
3.2 Change admin password.................................................................................................................8
3.3 Set controller to Single-door mode................................................................................................8
3.4 Set door opening time to 2s............................................................................................................9
3.5 Add User Card or Fingerprint.........................................................................................................9
3.6 Exit Management menu operation mode.....................................................................................9
3.7 User open door.................................................................................................................................9
4 Basic Functions........................................................................................................................................9
4.1 Management menu operations.......................................................................................................9
4.1.1 Change Admin Password.......................................................................................................9
4.1.2 Set admin card (or Fingerprint).............................................................................................10
4.1.3 Delete admin card(or fingerprint)..........................................................................................10
4.1.4 Set Machine Mode...................................................................................................................10
4.1.5 Limit types of reading card.....................................................................................................10
4.1.6 Restore to default settings.....................................................................................................11
4.1.7 Add User...................................................................................................................................11
4.1.7.1 Automatically generates ID numbers to add user card (or fingerprint).......................11
4.1.7.2 Specify ID number to add user card (or fingerprint)..................................................11
4.1.7.3 Specify first ID number to add serial number card users.........................................11
4.1.8 Delete user................................................................................................................................12
4.1.9 Set open door methods..........................................................................................................12
4.1.10 Set the number of doors opened by multi-user................................................................12
4.1.11 Set lock working mode..........................................................................................................12
4.1.12 Set Limits User Mode............................................................................................................12
4.1.13 Set Open-time........................................................................................................................13
4.1.14 Set notification to close door................................................................................................13
4.1.15 Set Alarm-time........................................................................................................................13
4.1.16 Set Anti-dismantle alarm function........................................................................................13
4.1.17 Set Anti-crack function..........................................................................................................13
4.1.18 Set LED indicator light mode...............................................................................................14
4.1.19 Adjust the brightness of the normally bright red indicator..............................................14
4.1.20 Set buzzer mode....................................................................................................................14

4.1.21 Adjust key volume.................................................................................................................14
4.1.22 Set reader output format......................................................................................................14
4.1.22.1 Set facility code..............................................................................................................14
4.1.22.2 Set D0 & D1 output format...........................................................................................14
4.1.22.3 Set wiegand output format for reading card or pressing fingerprint...........................15
4.1.22.4 Set wiegand output parity format for reading card or pressing fingerprint...........15
4.2 Admin card (or fingerprint) or PIN operation...............................................................................15
4.2.1 Set-card (or fingerprint) operation........................................................................................15
4.2.2 Add-card (or fingerprint) operation.......................................................................................16
4.2.3 Delete card (or fingerprint) operation...................................................................................16
4.2.4 Super-open-card (or fingerprint) operation.........................................................................16
4.2.5 Anti-duress-card (or fingerprint) operation..........................................................................16
4.2.6 Authorization-card (or fingerprint) operation.......................................................................16
4.2.7 Normal-open-card (or fingerprint) operation.......................................................................16
4.3 Users operation.................................................................................................................................17
4.3.1 Get user card or enter fingerprint..........................................................................................17
4.3.2 User open door ......................................................................................................................17
4.4 Other operation ...............................................................................................................................17
4.4.1 Cancel alarming.......................................................................................................................17
4.4.2 Admin password initialization................................................................................................17
4.4.3 Resort to factory settings........................................................................................................17
4.5 Operation characteristics in different machine modes...............................................................18
4.5.1 Operation characteristics in Reader mode..........................................................................18
4.5.2 Operation characteristics in Single-door mode..................................................................18
4.5.3 Operaton characteristics in Interlock mode.........................................................................18
4.5.4 Operation characteristics in Demo mode............................................................................18
5 Management menu summary table.....................................................................................................18
5.1 Reader mode management menu summary table.....................................................................18
5.2 Single-door mode (or Interlock mode) management menu summary table.................................20
5.3 Demo mode management menu summary table........................................................................22
6 Precautions in use...................................................................................................................................22
7 Common troubleshooting .....................................................................................................................23

1Overview
1.1 Introduction
This series of products adopt the appearance of anti-metal shielding patent technology,a
new 32-bit microcontroller ARM core design with powerful functions. They are very stable and
reliable. It’s a new generation of multi-function access controller, including Reader mode,
Single-door mode, Interlock mode, Demo mode etc. All of them could be widely used in office
buildings, homes, apartments, villas, single houses, banks, prisons and other places.
1.2 Function features
Zinc alloy shell, anti-metal shielding patent technology, no large area of non-metal card
reading window
Support 125Khz EM&HID card and 13.56Mhz Mifare card at the same time（ISO14443A）.
Low power consumption sensor optical fingerprint to open the door.
Infrared remote keyboard operation
Can be setted as Reader mode, Single-door mode, Interlock mode or Demo mode.
The output format can be set by users.
Supports 5 methods including card, fingerprint and Multi-cards to open the door.
Support Super-open-card(fingerprint) operation.
Support Add-card, Delete-card, Anti-duress-card, Authorization-card and Normal-open
card(fingerprint) operation.
Support Set-card （fingerprint）operation, for quick access to the management menu.
Infrared anti - demolition technology, can also alarm at night.
The unlock signal adopts the NO, NC, COM output of the relay.
Alarm signal output by MOS and it can be the driver of the alarm .
Fingerprint Standalone
Access Control User Manual

Fingerprint
1.3 Functional unit
Pro-P2 Special infrared remote control keyboard
1.4 Technical parameters
Working voltage: DC10～14V
Standby current: ≤50mA
Maximum distance of reading EM and HID cards: 5cm
Maximum distance of reading IC and CPU card: 2cm
Frequency: 125KHz and 13.56MHz
Output format: Wiegand 26-66 bit(HID automatic)
User capacity：20000
Admin card capacity: 21
User fingerprint capacity ：219
Admin fingerprint capacity of ：21
Electric lock signal relay contact current: ≤1A
Alarm signal MOS tube output current: ≤1A
Working environment temperature: -20～60℃
Working environment humidity: 0～95% (no condensation)
Dimension: 170*83*35mm
Button
Inductive optical
Card
Metal
Indicator
Infrared
Infrared emission tube
Film switch keypad
Standalone
Access Control User Manual

2 Installation, wiring and debugging
2.1 Packing list
No. Item Model Qty Note
1 Color box 1
2 Standalone access control 1
3 User manual 1
4 Punch stickers 1
5 Decorative sheet 1
6 Expansion rubber plug Φ6mm×30 mm 4 White
7 Self-tapping screw ΦKA3mm×25 mm 4 Galvanized
2.2 Installation and Wiring
Fingerprint Standalone
Access Control User Manual

①Put the Punch sticker on a suitable position on the wall, use a percussion drill to make an outlet
hole with a diameter greater than 14mm and four plastic screw holes with a diameter of 6mm,
and then insert four matching plastic screws; ②Use a screwdriver Unscrew the anti-dropping
screw just below the side of the product, remove the bottom case of the product, and fix the
bottom case on the wall with four matching self-tapping screws on the wall according to the hole
position of the bottom case. ③According to the selected wiring diagram, cut the lead wires to a
suitable length, and cut off the excess wires, and connect them to the system wires one by one
according to the wiring diagram through the wall or in the embedded box. Be careful not to
connect wrongly or Short circuit, otherwise the machine may be burnt out. After checking all is
correct, shortly power on to test whether the indicator light is normal and the buzzer beeps,
otherwise immediately cut off the power supply, recheck whether the wiring is correct, and after
it is correct, install the front shell of the product on the bottom shell on the wall. Remove the
screws and fix it. ④Attach the decorative sheet to the position of the anti-dropping screw.
The product wiring colors and functions are shown in the following table：
Color Symbol Functions
Red +12V Positive pole
Black GND Ground
Green D0 Wiegand signal, D0 input or output(or RS232-TTL signal output:
Tx)
White D1 Wiegand signal, D1 input or output(or RS232-TTL signal input : Rx)
Brown D_IN（LED）Door contact input (or external control input of green
LED)
Yellow OPEN（BZ）Exit button input(or external control input of buzzer)
Blue NO Normal open port of Relay
Purple COM Common port of Relay
Orange NC Normal close port of Relay
Grey Alarm- Alarm (or doorbell) signal MOS drain output
Fingerprint Standalone
Access Control User Manual

2.3 Debugging
Turn on the power, test according to the content of the introduction, until the electric lock
can be opened correctly with the card reader, fingerprint and exit button, the debugging is
completed.
3Getting Started
Writing Conventions:
Keypad operation only can be used between “0123456789*#” these12 buttons
“…” means continue similar operation as indicated from previous operations.
“,”is not an actual operation, it’s just punctuation.
“()” means the serials of digital numbers which will be type into the controller, like PIN code,
ID number ,card number
Operation Conventions：
“Beep-”one long beep means the operation was correct. “beep-beep-beep” three short
beeps mean operation was incorrect. LED light turn to green means operation was
successful
Fingerprint Standalone
Access Control User Manual

“#” means previous operation was received by system, it normally uses at the end of the
digital numbers of PIN code, ID number, card number or parameter, when you type this key
it means input is finished.
"*" means cancel the current operation or return to the previous menu.
Management menu fix to 2 digits, from 00~99, Don't press “#”, after entering the menu,
LED light turn to orange,if operation failed will hear“beep-beep-beep”3 short beeps.
Under the management menu operation mode, if system detected without any operation
over 30 seconds, it will back to standby mode automatically
Indicator light and buzzer prompt：
Operation Status Indicator light Buzzer
Standby mode Red
Successful operation Green A long beep
Operation incorrect 3 short beeps
When admin card enter 2 short beeps
When admin card exit A long beep
Press digit key A short beep
Press * key A long beep
Card & fingerprint Mode, after reading
the card
Red slow flash
Multi-user open door unfinished Red slow flash
Enter the admin main menu Red slow flash
Enter the setting status Orange
The unlock status Green
Alarm Red quick flash Alarm Sound
3.1 Enter management menu operation mode
* (Hold on for more than 2 seconds), (Input admin password) #
Note: Admin password is a 6 digits number, 888888 is the factory default admin password.
The user should change the admin password when use the device for the first time, otherwise
user cannot continue other operations. After input correct admin password, the LED light will
flash green for one time and then back to red flash status, all of the rest operations must under
this status.
3.2 Change admin password
00, (New admin password) #, (Repeat new admin password)#
Note: New admin password is a 6 digits number
Fingerprint Standalone
Access Control User Manual

3.3 Set controller to Single-door mode
Factory default setting is single door mode, if user does not sure about the mode, please
set it again, the steps please follow:
03, 1#
3.4 Set door opening time to 2s
Assuming it is an electric mortise lock, the factory default opening time is 2S, no
adjustment is required. Just adjust the unlocking time of the special power supply for access
control to the minimum. If you are not sure what the door opening time of the machine is, you
need to reset it. The steps are: 34, 2 #
3.5 Add User Card or Fingerprint
10, read card (or press fingerprint twice), read card (or press fingerprint twice) …repeat the
operation till the last user card.
Note: the controller can read multi-cards or fingerprints continuously, each fingerprint press
twice. When you hear a long “beep- “and indicator light turn to green it means the new card or
fingerprint added successfully. After finishing the last card or fingerprint, please press the * key
to exit.
3.6 Exit Management menu operation mode
In Management menu operation mode, press * more than once until the indicator light turn
to red and always bright means exit Management menu operation mode.
3.7 User open door
When the indicator light is red and always bright, read card, or press user fingerprint or
press exit button.
Note: When the door opens, there is a long "beep" sound and the indicator light turns to
green when the door is unlocked.
Fingerprint Standalone
Access Control User Manual

4 Basic Functions
4.1 Management menu operations
In all modes, the steps of entering the management menu:
* key (Hold on for more than 2 seconds), (Admin Password)#
or to read Set-card
Note: Admin Password is 6 digits, 888888 is the factory default admin password. User
should change the Admin Password when use the device for first time, otherwise user cannot
continue other operation. If the Admin Password is correct, the indicator light will turn to green
once and then back to red flash status. Other operations must be performed in this status. If the
user who forget the admin password or user who need to use the management menu for many
times can use this method by read the Set-card instead keypad operation.
4.1.1 Change Admin Password
00,(New Admin Password)#,(Repeat Admin Password)#
Note: New Admin Password must be 6 digits.
4.1.2 Set admin card (Fingerprint)
01, 0#, read card(or press fingerprint twice), …, Set 1-3 Set-cards(or fingerprint).
01, 1#, read card(or press fingerprint twice), …, Set 1-3 Add-cards(or fingerprint).
01, 2#, read card(or press fingerprint twice), …, Set 1-3 Delete-cards(or fingerprint).
01, 3#, read card(or press fingerprint twice), …, Set 1-3 Super-open-cards(or fingerprint).
01, 4#, read card(or press fingerprint twice), …, Set 1-3 Anti-duress-cards(or fingerprint).
01, 5#, read card(or press fingerprint twice), …, Set 1-3 Authorization-cards(or fingerprint).
01, 6#, read card(or press fingerprint twice), …, Set 1-3 Normal-open-cards(or fingerprint).
Note: Each type of admin card(or fingerprint) can be divided several times to set till to 3pcs.
4.1.3 Delete admin card(or fingerprint)
02, 0000#, delete all 21 admin cards(or fingerprint).
Fingerprint Standalone
Access Control User Manual

02, 0#, delete 3 Set-cards(or fingerprint).
02, 1#, delete 3 Add-cards(or fingerprint).
02, 2#, delete 3 Delete-cards(or fingerprint).
02, 3#, delete 3 Super-open-cards(or fingerprint).
02, 4#, delete 3 Anti-duress-cards(or fingerprint).
02, 5#, delete 3 Authorization-cards(or fingerprint).
02, 6#, delete 3 Normal-open-cards(or fingerprint).
4.1.4 Set Machine Mode
03, 0#, Set to Reader mode.
03, 1#, Set to Single-door mode.
03, 3#, Set to Interlock mode.
03, 9#, Set to Demo mode.
Note: Factory default mode is Single-door mode.
4.1.5 Limit types of reading card
04, 0#, cannot read any card.
04, 1#, can read EM card only.
04, 2#, can read HID card only.
04, 3#, can read IC card only.
04, 4#, can read EM+HID card.
04, 5#, can read EM+IC card.
04, 6#, can read HID+IC card.
04, 7#, can read EM+HID+IC card.
4.1.6 Restore to default settings
09，0000#
Note: After Restore to default settings, Admin Password is unchanged, Machine mode is
unchanged, admin cards and user card information are not deleted, and the specific default
values are shown in the appendix.
Fingerprint Standalone
Access Control User Manual

4.1.7 Add User
4.1.7.1 Automatically generates ID numbers to add user card (or fingerprint)
Read card(or fingerprint) continuously to add user:
10, read card(or press fingerprint twice ), … *
Input 8-digit format card number to add user
10, 8# (8-digit format card number) #, 8# (8-digit format card number) #, …*
Input 10-digit format card number to add user:
10,10# (10-digit format card number) #, 10# (10-digit format card number) #, …*
Note: For example, card number is: 0004301875, 06542035, front numbers are 10-digit
format card number, the following numbers are 8-digit card number, 00 in front of number can
be omitted, you can input 4301875 or 65,42035. The card number not separated by commas or
other symbols is considered as 10-digit format card number. The following sections are dealt
with according to this rule.
4.1.7.2 Specify ID number to add user card (or fingerprint)
Specify ID number and read card to add user:
11, (ID) #, read card (or press fingerprint twice), … *
Specify ID number and input 8-digit card number to add user:
11, (ID) # 8# (8-digit format card number) #, (ID) # 8# (8-digit format card number)
#, …*
Specify ID number and input 10-digit format card number to add user:
11, (ID) # 10# (10-digit format card number) #, (ID) # 10# (10-digit format card number)
#, … *
Note: ID number are 1~5 digits between 1~20000.
4.1.7.3 Specify first ID number to add serial number card users
Add 8-digit format serial number card users:
12, (ID) #, 8# (8-digit format card number) #, (card quantity) #
Add 10-digit format serial number card users:
12, (ID) #, 10# (10-digit format card number) #, (card quantity) #
Note: ID number are 1~5 digits, the range is 1-20000, ID number plus card quantity must
be less or equal to 20001. After add serial number cards, the first card will be based on ID
number and card number, each time add one card, ID number and card number will add 1 at the
same time till to all card is added. In order to prevent duplication of card numbers, please delete
all user cards and admin cards before add serial number cards.
Fingerprint Standalone
Access Control User Manual

4.1.8 Delete user
Delete all users:
20, 0000#
Delete user card by read card(or fingerprint):
21, read card(or press fingerprint once), …
Delete user by input 8-digit format card number:
21, 8# (8-digit format number) #, 8# (8-digit format number) #, …
Delete user by input 10-digit format card number:
21, 10# (10-digit format number) #, 10# (10-digit format number) #, …
Delete user by input ID number
22, (ID) #, (ID number) #, …
4.1.9 Set open door methods
30, 0#, open door by card.
30, 2#, default value, open door by cards or fingerprint.
30, 3#, open door by fingerprint.
30, 5#, open door by card and fingerprint.
30, 6#, open door by multi-user.
Note: Super-open-card is not affected by any open door method; you can open door at any
time. Open door by multi-user refer to open door by multi-card or multi-fingerprint, if card and
fingerprint are the same ID, as one user.
4.1.10 Set the number of doors opened by multi-user
31, (2-10)#, read 2-10 cards (or fingerprints) in order to open the door (the door opening
mode must be set to the multi-user opening mode)
4.1.11 Set lock working mode
32, 0#, default value, set lock to Delay mode. After an unlock operation, the lock is opened ,
then the lock will be closed automatically after a few moment of delay. Apply to normal open.
32, 1#, set lock to Switch mode. After an unlock operation, the lock will keep opening until
another unlock operation again, the lock will keep locking, and so on.
32, 2#, set lock to Normal-open mode. Under this mode, the lock will keep opening, not
controlled by other unlocking action. If the user don’t want to use the Normal-open mode,
please set the mode to the other two modes.
Note: A better way to implement the Normal-open mode is operation by Normal-open card
Fingerprint Standalone
Access Control User Manual

(or fingerprint) in the first mode, it can switch to Normal-open mode and normal status quickly.
The operation of Normal-open card(or fingerprint), see relevant chapter of admin cards(or
fingerprint) operation.
4.1.12 Set Limits User Mode
33, 0#, disable users to use.
33, 1#, default value, enable users to use.
Notes: A better way to implement the limits of user mode is operation by
Authorization-card(or fingerprint), it can switch to disable and enable users to operate quickly.
The operation of Authorization-card(or fingerprint), see relevant chapter of admin cards(or
fingerprint) operation.
4.1.13 Set Open-time
34, 0#, set Open-time to 50mS, apply to electrically controlled lock for external
instantaneous large current
34, (1-999) #, the default value is 2, set Open-time from 1 to 999s.
Note: Unlock-time of Access Controller’s special power supply should set to minimum time
to ensure the actual Unlock-time match with user’s settings.
4.1.14 Set notification to close door
35, (0-99) #, the default value is 10, set the time to notify when user don’t close the door
after open it beyond the setting time. the buzzer begin to beep for notification.
36, (0-99) #, the default value is 10, set the time for beeping.
Note: If you don’t need notification, can set the time for beeping to 0.
4.1.15 Set Alarm-time
40, 0#, default value, if set Alarm-time to 0 means no alarm.
40, (0-99) #, Alarm-time is set from 1 to 99 minutes.
4.1.16 Set Anti-dismantle alarm function
41, 0#, default value, disable Anti-dismantle alarm function.
41, 1#, enable Anti-dismantle alarm function.
Note: When the machine is illegally dismantled, it alarms and an alarm signal will be send
out at the same time. The alarm can be canceled by inputting Admin Password, read admin
card(or fingerprint) or user card(or fingerprint).
Fingerprint Standalone
Access Control User Manual

4.1.17 Set Anti-crack function
43, 0#, default value, normal working mode.
43,1#, alarm working mode, when error operation times more than allowed times, the
machine alarm will beeps and it send out alarm signal.
43, 2#, locked working mode, when error operation times more than allowed times, the
machine will lock up for some time. User cannot press any key or read card during that time.
44, (1-10)#, default value is 10, set maximum times for the error operation from 1 to 10 .
45, (1-99)#, default value is 10, after the error operation exceeds the set maximum number
of times, it will be locked for 1-99 minutes.
Note: Anti-crack function refers to prevent illegal and unlimited password or card crack to
open the door in a short period of time, the basic method is within 10 minutes of invalid
password or invalid card number read error exceeds the default setting, the controller will alarm
or lock up for some time.
4.1.18 Set LED indicator light mode
50, 0#, standby, LED indicator light is off.
50, 1#, default value, standby, LED indicator light always red.
50, 2#, standby, LED turns green in reader mode, LED turns red in other modes.
4.1.19 Adjust the brightness of the normally bright red indicator
51, 1, 1, ... ,decrease brightness
51, 2, 2, ..., increase brightness
Note: The brightness of the indicator light can be adjusted total 21 different levels. Each
time you press the “1” key, it decrease 1 level of brightness. Press and hold on the “1” key, the
brightness will continuously decrease. When it reaches to minimum level of brightness, the
controller will beep twice. Each time you press the “2” key, it increase the level of brightness.
Press and hold on the “2” key, the brightness will continuously increase. When it reaches to the
maximum brightness the controller will beep twice.
4.1.20 Set buzzer mode
54, 0#, disable buzzer.
54, 1#, default value, enable buzzer.
Fingerprint Standalone
Access Control User Manual

Note: Enable or disable buzzer only concern normal users operation, such as the sound of
opening door by read cards. When you press the * key for 2 seconds, the buzzer is forced to
enable, such as entering the management menu . In addition, the alarm tone is not controlled
by the setting, and the buzzer can still send an alarm tone when the buzzer disable.
4.1.21 Adjust key volume
55, 1, 1, ... , decrease volume.
55, 2, 2, ... , increase volume.
Note: The key volume can be adjusted at 15 levels. Each time you press the 1 key,
decrease 1level of volume, press the 1 keys do not move quickly and automatically decrease
the volume, when it has been adjusted to a minimum volume, "beep" twice, each time you press
the 2 key, increase 1 level of volume, press the 2 keys do not move quickly and automatically
increase the volume, when it have been adjusted to the maximum volume, "beep" twice.
4.1.22 Set reader output format
4.1.22.1 Set facility code
60, (0-255)#, default value is 0, set facility code.
Note: The facility code will be used when fingerprint ID output, See the following sections
for specific use.
4.1.22.2 Set D0 & D1 output format
61, 0#, D0 & D1 output wiegand format.
61, 1#, D0 output RS232-TTL-HEX format.
61, 2#, D0 output RS232-TTL-ASCII-8 format
61, 3#, D0 output RS232-TTL-ASCII-10 format.
Note: The wiegand format is an international protocol for access control products. But the
width of pulse and interval time are different. Our standard: Pulse’s high level is 5V and low
level is 0V. Width is 40uS,interval time is 2mS.
RS232-TTL-HEX format refers to the standard RS232 communication protocol data output,
TTL level 0-5V, the output data is output by the card byte HEX format.
The output RS232-TTL-ASCII-8 format is the output data is ASCII character format, card
number data is 8 bit format, and same as the ordinary EM card marked on the 8 bit card number,
but omit the 0 in front of it.
The output RS232-TTL-ASCII-10 format is the output data is ASCII character format, card
number data is 10 bit format, and same as the ordinary EM card marked on the 10 bit
Fingerprint Standalone
Access Control User Manual

card number, but omit the 0 in front of it.
For example, a 3 byte number of RS232-TTL-HEX format is A83EF6, the actual output is
A83EF6, the RS232-TTL-ASCII-8 format is 168,16118, the actual output is 16816118, the
RS232-TTL-ASCII-10 format is 0011026166, the actual output is 11026166.
4.1.22.3 Set wiegand output format for reading card or pressing fingerprint
62, (26-66)#, default value is 26, the Wiegand output format for reading card or pressing
fingerprint can be set from 26-66
When pressing a valid user fingerprint, the output format is that the lower 2 bytes are the
fingerprint user ID number, and the lower 3 byte is the machine device number. If the machine
device number is 3 and the fingerprint ID is 12, the output data is equivalent to the 26-bit card
number 003,00012. If the card number in other formats is output, the high digits should be filled
with 0.
4.1.22.4 Set wiegand output parity format for reading card or pressing fingerprint
63, 0# wiegand output without parity check.
63, 1# default value, wiegand output with parity check (EO format)
Note: EO format is standard wiegand format. Even check data add in front and Odd check
data add in the end.
4.2 Admin card (or fingerprint) or PIN operation
4.2.1 Set-card (or fingerprint) operation
The main function of Set-card (or fingerprint) is to replace the input Admin Password
into the management menu operation. It is suitable for forgetting the Admin Password or
frequently entering the management menu operation. Its operation is:
Read Set-card (or fingerprint), equivalent to operation: * ( Press for more than 2
seconds), (Admin password) #.
Note: After reading Set-card (or fingerprint), the indicator lights are red flashing,
indicating that the management menu operation mode has been entered and other
operations can be performed.
4.2.2 Add-card (or fingerprint) operation
Read Add-card (or fingerprint), read user card (or fingerprint), read user card (or
fingerprint), .... read Add-card (or fingerprint).
Note: Add-card (or fingerprint) is mainly used for rapid continuously to add the user
Fingerprint Standalone
Access Control User Manual

card, first read Add-card (or fingerprint), sound two short “beep”, light is orange, indicating
to enter the add user card state, second read Add-card (or fingerprint), sound a long
“beep” , light turns red, indicating to exit add user card state.
4.2.3 Delete-card (or fingerprint) operation
Read Delete-card (or fingerprint), read user card (or fingerprint), read user card (or
fingerprint), .... read Delete-card (or fingerprint).
Note: Delete-card (or fingerprint) is mainly used for rapid continuously to delete the
user card, first read Delete-card (or fingerprint), sound two short “beep” sound, light is
orange, indicating to enter the delete user card state, second read Delete-card (or
fingerprint), sound a long “beep”, light turns red, indicating to exit delete user card state.
4.2.4 Super-open-card (or fingerprint) operation
Read Super-open-card (or fingerprint).
Note: Super-open-card (or fingerprint) has the highest open authority, in a variety of
way to open the door, or restrict the user to open the door, the Super-open-card (or
fingerprint) can open the door.
4.2.5 Anti-duress-card (or fingerprint) operation
Read Anti-duress-card (or fingerprint).
Note: Anti-duress-card (or fingerprint) have the same authority with Super-open-card
(or fingerprint). The only difference is after reading Anti-duress-card(or fingerprint), the door
will open while outputting alarm signal.
4.2.6 Authorization-card (or fingerprint) operation
Read Authorization-card (or fingerprint) once, two short beeps, limit users.
Read Authorization-card (or fingerprint) again, one long beep, release limit.
Note: Authorization-card (or fingerprint) authorizes users. By default, users can
operate properly, you can use an Authorization-card (or fingerprint) when you need to
restrict user access.
4.2.7 Normal-open-card (or fingerprint) operation
Read Normal-open-card (or fingerprint) once, two short beeps, lock keep open, not
controlled by other unlocking action.
Read Normal-open-card (or fingerprint) again, one long beep, release normal open
state.
Fingerprint Standalone
Access Control User Manual

4.3Users operation
4.3.1 Get user card or enter Fingerprint
Users must obtain the user card or entering fingerprint from the administrator for the
first time.
4.3.2 4.3.2 User open door
Open door by user card or fingerprint:
read user card, or fingerprint.
Open door by user card and fingerprint:
Read user card, press the user’s fingerprint in 5 seconds.
Open door by multi-users:
Read user card (or fingerprint), read another user card (or fingerprint) in 5 seconds ….
Exit operation:
Press exit button
Note: In addition to the exit operation, make sure that the machine is not in a disable
user state. You must first set up good way to open the door, open the door by multi-card
also needs to set a good quantity of card. If card or PIN is valid, a long “beep”, the lock will
be opened. During the opening time, LED turns green. After that, LED turns red and keep.
In card & PIN open mode or multi-card open door mode, the interval time of reading card
or inputting PIN cannot be more than 5 seconds.
4.4 Other operations
4.4.1 Cancel alarming
Read admin card (or fingerprint) or the user card (or fingerprint), or Admin Password #.
Note: When the alarm has happened, the buzzer will ring "Wu, Wu" alarm sound. User
can cancel the alarm by reading the valid user card (or fingerprint) and entering Admin
Password. But the alarm output signal can’t be canceled by reading the anti-duress card.
4.4.2 Admin Password initialization
When you forget the Admin Password, you can restore it to the initial password by
special operation. Operation is as follows:
Power off, and then power on again, press # key in one second within the indicating light
turn orange, then you will hear two “beep”, and a long beep, admin password has restored
to 888888. But the other parameters, the info of the card and fingerprint will be still kept.
4.4.3 Restore factory settings
Fingerprint Standalone
Access Control User Manual