Nortel Norstar T7316E User manual

T24 KIM Installation
T24 Key Indicator Module
(KIM) Installation Card
The T24 Key Indicator Module (KIM) is an add-on device which provides 24 extra memory or
line buttons for the T7316E telephone. Up to nine KIMs can be connected to a T7316E
telephone.
A Station Auxiliary Power Supply (SAPS) is required for T7316E telephones that have five to
nine KIMs attached. For SAPS installation instructions, refer to the SAPS Installation Card
provided with the SAPS kit.
Single T24 KIM installation Multiple T24 KIM installation
1Position the metal hooks
from the left side of the KIM
next to the slots on the right
side of the T7316E
telephone.
Firmly press the T7316E and KIM together.
1Position the T7316E
telephone and KIMs
together. Align the
hooks on each KIM
to the slots on the
next KIM.
Firmly press the T7316E and KIMs together.
2Slide the KIM down until its
aligned with the T7316E
telephone.
2Slide the KIMs down
until they are aligned
with the T7316E
telephone.
3Remove the stand
from the T7316E
telephone.
3Remove the
stands from
KIMs and
the T7316E
telephone.
4Connect the KIM
cord to the accessory
connector port on the
T7316E telephone.
4Connect each KIM
cord to the connector
port on the next KIM
in a daisy-chain
order.
5Replace the stand on the T7316E telephone to
complete the installation. 5Connect the cord on the first KIM
to the accessory
connector port on
the T7316E
telephone.
6Replace the stands on the KIMs and the
T7316E telephone to complete the installation.
Press here
to remove stand
.
Press here
to remove
stands.
KIM 1
KIM 2
KIM 3
KIM 1
Cord to
T7316E

2
T24 KIM initialization
KIM indicators turn on and flash during the first ten seconds
after powering up. It can take up to five minutes for the KIM
to initialize.
The default setting for the programmable memory buttons
on the KIM is blank. The side illustration shows the button
number assignment on a KIM.
Troubleshooting Tip: An Addon Error message appears
on the T7316E telephone display and an error tone is
generated when there is a connector problem with a KIM.
Check that the KIM cord is properly inserted into the
accessory connector port of the T7316E telephone.
T24 KIM coldstarts
Internal autodial numbers can be automatically assigned to the programmable memory buttons on the
KIM when a coldstart is performed. Internal autodial numbers are assigned in ascending order starting
on the top left button (button 01) on the KIM. A coldstart must be performed during the first ten seconds
after powering up a KIM.
To coldstart an individual KIM To coldstart all KIMs
1Unplug the T7316E telephone line cord, then
reconnect it to power up. 1Unplug the T7316E telephone line cord, then reconnect it to power up.
2While the indicators are
flashing on the individual
KIM, simultaneously press
the top two and the bottom
two buttons on the lower
button set of the KIM, as
shown in the illustration
(buttons: 05, 12, 17 and 24).
2While the indicators are
flashing on the first KIM
(next to the telephone),
simultaneously press the
top two buttons and the
bottom two buttons on the
KIM, as shown in the
illustration.
(buttons: 01, 12, 13 and 24)
3At the beginning of the coldstart, indicators beside
each KIM button will briefly flash starting at the
bottom right button (button 24).
3At the beginning of the coldstart, indicators beside
each KIM button will briefly flash starting at the
bottom right button (button 24).
4When the KIM coldstart is completed, the T7316E
telephone display automatically returns to the time
and date.
4When the KIM coldstart is completed, the T7316E
telephone display automatically returns to the time
and date.
B09
B10
B11
B12
B08
B05
B06
B07
B20
B21
B22
B23
B24
B17
B18
B19
B04
B01
B02
B03
B16
B13
B14
B15
1-800-4 NORTEL
www.nortel.com
P0603481_02
Printed in Canada
KIM button number assignment