Nortel BayStack 380-24F 1000 Instruction Manual

Part No. 214390-A
December 2002
4655 Great America Parkway
Santa Clara, CA 95054
Installing the
BayStack 380-24F 1000 Switch

2
214390-A
[Draft Level—Nortel Confidential]
Copyright © 2002 Nortel Networks
All rights reserved. December 2002.
The information in this document is subject to change without notice. The statements, configurations, technical data, and
recommendations in this document are believed to be accurate and reliable, but are presented without express or implied
warranty. Users must take full responsibility for their applications of any products specified in this document. The
information in this document is proprietary to Nortel Networks Inc.
Trademarks
Nortel Networks, the Nortel Networks logo, the Globemark, Unified Networks, and BayStack are trademarks of Nortel
Networks.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, Nortel Networks NA Inc. reserves
the right to make changes to the products described in this document without notice.
Nortel Networks NA Inc. does not assume any liability that may occur due to the use or application of the product(s) or
circuit layout(s) described herein.
Federal Communications Commission (FCC) Statement
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which
case users will be required to take whatever measures may be necessary to correct the interference at their own expense.
EN 55 022 Declaration of Conformance
This is to certify that the Nortel Networks BayStack 380-24F 1000 Switch is shielded against the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by
the application of EN 55 022 Class A (CISPR 22).
Caution: This device is a Class A product. In a domestic environment, this device can cause radio
interference, in which case the user may be required to take appropriate measures.

Installing the BayStack 380-24F 1000 Switch
3
[Draft Level—Nortel Confidential]
About this guide
This guide provides instructions to install the Nortel Networks* BayStack* 380-24F 1000 switch
on a table or in an equipment rack. For more detailed information about the switch, refer to Using
the BayStack 380-24F 1000 Switch (part number 214391-A).
This guide includes information about the following topics:
• Environmental requirements for the installation site (next)
• Installing the switch on a table (page 5) or in a rack (page 6)
• Network connection requirements (page 7)
• Connecting AC power (page 8)
• Descriptions of LEDs (page 8)
• Initial switch setup (page 9)
Before you begin
Make sure the area where you will install and use the BayStack 380-24F 1000 Switch meets these
environmental requirements:
• Ambient temperature between 41°and 104°F (5° and 40°C)
• Relative humidity between 5% and 85% noncondensing
• No nearby heat sources such as hot air vents or direct sunlight
• No nearby sources of severe electromagnetic noise
• No excessive dust
• Adequate power source within six feet; one 15-Amp circuit required for each power supply
• At least 2 inches (5.08 cm) on each side of the switch unit for ventilation.
• Adequate space at the front and rear of the switch for access to cables.
If you are installing a single BayStack 380-24F 1000 Switch on a table or shelf, make sure the
surface will support at least 5 to 10 pounds.
Note: The direction of air flow in the BayStack 380-24F switch is from left to right.

214390-A
4
[Draft Level—Nortel Confidential]
Package contents
1 = BayStack 380-24F 1000 Switch
2 = Rack-mounting hardware:
• Rack-mount brackets
• Screws for attaching brackets to the switch
• Screws for attaching the switch to the equipment rack
3= Rubber footpads
4= Documentation Kit
•Read Me First sheet
• Installing the BayStack 380-24F 1000 Switch
• Warranty
• Software license agreement
• Safety Instructions
10524F
C
3
4
1
2
BayStack 380-24F Switch

Installing the BayStack 380-24F 1000 Switch
5
[Draft Level—Nortel Confidential]
Installing the switch on a
table or shelf
You can install a single BayStack 380-24F 1000 Switch on any flat surface that can safely support
the weight of the switch (5 to 10 pounds).
1Attach the rubber feet at the marked
locations.
9984F
C
2Set the switch on a table or shelf.
Allow at least 2 inches (5.1 cm) on each side
for proper ventilation and at least 5 inches
(12.7 cm) at the back for power cord clearance.
9985F
C

214390-A
6
[Draft Level—Nortel Confidential]
Installing the switch in an equipment rack
Required tool: Phillips screwdriver for attaching brackets to the switch
Rack requirements:
• A space of 2.8 inches is provided for each switch in an EIA or IEC standard 19-inch
(48.2-centimeter) equipment rack.
• The rack is bolted to the floor and braced if necessary.
• The rack is grounded to the same grounding electrode used by the power service in the area.
The ground path must be permanent and must not exceed 1 ohm of resistance from the rack to
the grounding electrode.
1Attach a bracket to each side of the switch.
The bracket with the round holes goes on
the right side of the switch, where the
round fan vents are located.
2Slide the switch into the rack. Insert and
tighten the rack-mount screws.
10525F
B
10526FB

Installing the BayStack 380-24F 1000 Switch
7
[Draft Level—Nortel Confidential]
Connection requirements
Refer to the following tablesfor connector pin assignments.
Required cables:
1000 BASE-T ports: For 1000 Mb/s operation: Category 5 UTP cable
Console port: Serial cable with DB-9 female connector on one end
GBIC and Mini-GBIC
ports: Varies with the installed GBIC or mini-GBIC; refer to the documentation that was shipped with the GBIC for specifications.
Table 1 Pin assignments in the Console port
Connector Pin number Signal
1 Carrier detect (not used)
2 Transmit data (TXD)
3 Receive data (RXD)
4 Data terminal ready (not used)
5 Signal ground (GND)
6 Not used
7 Request to send (not used)
8 Not used
9 Ring indicator (not used)
15
69
9473E
A

214390-A
8
[Draft Level—Nortel Confidential]
AC power specifications
Checking LEDs
Refer to the illustration and tables that follow for descriptions of the LEDs on the BayStack
380-24F 1000 Switch. The tables describe LED operation for a switch that has completed its
power-on self-tests.
Figure 1 BayStack 380-24F 1000 Switch LED display panel
Input current: 1.5A at 100 VAC
Input voltage (rms): 100 to 240 VAC at 47 to 63 Hz
Power consumption: 150 W
Thermal rating: 1000 BTU/hr maximum
Console
Pwr
Status
RPSU
1 5 7 9 11 13 15 17 193
2 6 8 101214161820
21 23 Link
Activity
Link
Activity
22 244
BayStack 380-24F Switch
10/100 BASE-T
Out-of-band
Management
Only
10473E
B

Installing the BayStack 380-24F 1000 Switch
9
[Draft Level—Nortel Confidential]
Table 2 BayStack 380-24F switch LED descriptions
Initial switch setup
The BayStack 380-24F 1000 Switch begins switching as soon as you attach network devices and
connect the switch to power. To manage the switch over the network or to perform TFTP
operations, you must set certain IP parameters. Refer to Using the BayStack 380-24F 1000 Switch
for more information about the console menus and configuring your switch.
Label Type Color State Meaning
Pwr Power status Green On DC power is available to the switch’s internal circuitry.
Off No AC power to switch or power supply failed.
Status System
status Green On Self-test passed successfully and switch is operational.
Blinking A nonfatal error occurred during the self-test. (This
includes nonworking fans.)
Off The switch failed the self-test.
RPSU RPSU status Green On The switch is connected to the RPSU and can receive
power if needed.
Off The switch is not connected to the RPSU or RPSU is not
supplying power.
1000 Speed
Indicator Green On The corresponding port is set to operate at 1000 Mb/s and the link is good.
Blinking The corresponding 1000 Mb/s port has been disabled by
software.
Off The link connection is bad, or there is no connection to
this port.
Link Link status Green On Valid communications link established.
Off The communications link connection is bad or there is no
connection to this port.
Blinking The corresponding port is management disabled.
Activity Port activity Green Blinking Indicates network activity for the corresponding port. A
high level of network activity can cause the LEDs to
appear to be on continuously.

214390-A
10
[Draft Level—Nortel Confidential]
Setting IP parameters
For the initial setup of a standalone switch, you must set the following IP parameters:
• IP address of the switch
• Subnet mask
• Gateway address.
To set the IP parameters:
1Connect a terminal to the Console port on a standalone switch.
Set the terminal protocol as described in Using the BayStack 380-24F 1000 Switch.
2Connect the switch to power.
3After the Nortel Networks logo is displayed, press [Ctrl]-Y to display the Main Menu.
The screen displays the Main Menu for the switch.
Figure 2 BayStack 380-24F Main Menu screen