Notifier AM-6000 User manual

Installation Manual
Document : M-180.2-AM6000-ENG
Issue :10/1999 Rev. :B.2
AM-6000
Analog Fire Alarm
Control Panel
NOTIFIER ITALIA
A Division of Pittway Corporation

INDEX
»This new revision, B.2, includes an Appendix on page 27 about “AM-6000 Power Supply”.
AM-6000 Exploded View1
Cabinet2
Mounting the system boards to the “ICA-6” chassis3
Front Panel indication & keypad4
“BE-600A” Main Board layout5
Connector CNA on “BE-600 A” board 6
Connector CN0 “BE-600 A” board 6
Serial Printer connections 6
Connector CN1 on “BE-600 A” board 7
“BPS-600” board for 230 V Mains wiring8
Wiring the “BE-600 A” Main Board external devices9
Detector and Module wiring - Typical LOOP line (style 6)10
“LIB-600” Expansion Board layout11
Connector CN1 on “LIB-600” Expansion Board12
“AVPS-6” Aux. Power Supply Board 13
“DIA-6”: front panel display and keypad interface layout14
Analog identification system components 15
Class “A” wiring circuit and line isolators16
Notes about loop wiring17
SLC LOOP shield wiring 21
Connector CN2 on “SIB-600” optional board 22
The 220 VAC Power Supply Line 23
Main Power Supply current draw calculation24
Alarm condition current load25
Battery capacity calculation26
APPENDIX: AM-6000 POWER SUPPLY (Refer to note 1)
Note 1: Added in this new revision
Index.VPInstallation Manual
Doc. M-180.2-AM6000-ENGRev. B.2NOTIFIER ITALIA

AM-6000 EXPLODED VIEW
Page 1 Installation Manual AM-6000-60002.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
ATTENZIONE
230 V
ATTENZIONE
230 V
126
1
1
12
12
126
126
126
AVPS 6 Board for 3 A Aux. Power Supply
complete of transformer
BE 600 A
Main Board
including support
and transformer
CVCV-0117 Power Supply Cable
DR 6 Dust Preventer Door
CVCV-0125 : 3-board Flat Cable
ICA 6 CHASSIS
LIB 600 Expansion Board (Board 1)
LIB 600 Expansion Board (Board 2)
LIB 600 Expansion Board (Board 3)
DP 6 Dress Panel (3 U)
CVCV-0123 Flat Cable
CAB 6 Wall- mounting Cabinet
SIB 600 Serial Board
SK8 R, SK16 R
Relay Board
BPS600 Board for 230 V Mains Wiring
CVCV-0124 Flat Cable
DIA 6 Front Board
Operator Keypad
•
DIA 6M-I (Italian)
•
DIA 6M-E (English)
•
DIA 6M-S (Spanish)

CABINET
AM-6000-60001.VP Installation Manual Page 2
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
65 mm 405 mm
535 mm
65 mm
75 mm
55 mm
46.5 mm
30.5 mm
35 mm
30
mm
30
mm
35
mm
35
mm
75
mm
75
mm
35
mm
35
mm
35
mm
35
mm
35
mm
35
mm
105 mm 105 mm
45
mm
45
mm
365 mm 440 mm
200 mm
30 mm
.
.
4 Mounting Holes
> screw max. Dia. : 6.0 mm.
4 openable holes
28.0 mm. dia.
1 openable hole - 28.0 mm. dia.
> bottom side
Openable Holes 28.0 mm dia.
> 2 bottom side
> 2 top side
Dust preventer door

MOUNTING THE SYSTEM BOARDS to the “ICA-6" CHASSIS
INSTALLING THE ICA-6 CHASSIS
1 - Screw the two spacers4x45MF( A ) to the plate.
2 - Secure the metal plaquette ( B ) with the two screws4x8TC( C ).
3 - Insert the chassis on the proper hinges ( D ). Then push the chassis inward toward the bottom of the cabinet.
A click will confirm the correct seat of the chassis ( E ).
Page 3 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG

FRONT PANEL INDICATION & KEYPAD
DIMENSIONS
•
Front panel including the hinge = 482 x 266 mm (19" - 6 units).
•
Mounting holes wheel-base : Horizontal = 465 mm. - Vertical = 190 mm.
AM-6000-60001.VP Installation Manual Page 4
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
NOTIFIER
Division of Pittway Corporation
INTELLIGENT FIRE DETECTION SYSTEM
AM-6000
NEXT
KJIH
Z
O
NM
U
TS
)
R
SPACE
X
V W
G
Q
Y
LAMP
TEST
LAMP
TEST
4
7
5
8
0
6
9
ACK
READ
STATUS
READ
STATUS
MODIFY
STATUS
MODIFY
STATUS
PROGRAMMING
SPECIAL
FUNCTIONS
SPECIAL
FUNCTIONS
REPEAT
ED
C
B
A
F
P
L
(
SIGNALSILENCE
SYSTEM
RESET
SYSTEM
RESET
SYSTEM
TEST
SYSTEM
TEST
LISTLISTRESTORE
SILENCE
RESTORE
SILENCE
1
SILENCED CONTROLS SILENCED CONTROLS
23
ALARM
DISABLED ZONES/POINTS DISABLED ZONES/POINTS GENERAL TROUBLE GENERAL TROUBLE SYSTEM TROUBLE SYSTEM TROUBLE
PANELOK

“BE-600 A” MAIN BOARD LAYOUT
Page 5 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
1 26
1
1
12
12
Led indicating trouble condition (Line 1-4)
CPU-Reset push-button
Led indicating alarm condition (Line 1-4) Connector for SIB 600
Serial Board interconnection
CRT/LCD serial communication
line Status LED
Product identification
Factory code number
Siren Fuse 3 A 15 (Monitored Line)
Jumper to Enable/Disable
Earth trouble Signal
Start-up from battery only.
(Execute a short circuit between the two PIN)
Connector for BPS 600 PSU board
interconnection
Earth: connect to SIB 600 serial Board
Earth: connect to LIB 600 expansion boards
Control Panel powered Led
Battery Low Trouble Led
Printer serial communication
line Status Led
Connector for AVPS 6 auxiliary
Power supply interconnection
Earth: connect to AVPS 6 auxil. power supply
Connector for DIA 6 front board interconnection
Connector for LIB 600
expansion board interconnection
Connector for future expansion
4 Status Leds concerning the detector line serial communication
Detection Lines (1-4)
Program Eprom
User Fuse 3 A 15 + 24 V
Positive to Earth
Negative to Earth
}

CONNECTOR CNA on “BE-600 A” BOARD
CONNECTOR CN0 on “BE-600 A” BOARD
NOTE: ( * ) these two outputs CANNOT operate simultaneously. The operator must select the Type of Connection to
employ, from the Control Panel Main Programming Menu (refer to AM-6000 Programming Manual).
SERIAL PRINTER CONNECTIONS
AM-6000-60001.VP Installation Manual Page 6
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
TERMIN. NR. DENOMINATION NOTE USE FOR : CABLE COLOUR/NR.
1 + 24 V User 0,5
2 GND P 2A
3 + 24 V User Resettable 0,5 ISOLATED BY MANUAL RESET
4 GND P 2A
5 Siren Supervis.Line+(Stand by) 3A
6 Siren Supervis.Line -(Stand by)
7 SIGNAL SILENCE N.O. CONTACT
8 RESET N.O. CONTACT
9 + 24 V Auxiliary 3 A ONLY IF AVPS 6 IS INSTALLED
10 GND P ONLY IF AVPS 6 IS INSTALLED
11 + 24 V Aux. Resettable 3 A ONLY IF AVPS 6 IS INSTALLED
12 GND P
TERMIN. NR. DENOMINATION NOTE USE FOR : CABLE COLOUR/NR.
1 GROUND
2 RS 232 TX - PRN 2400 Baud
3 RS 232 RX - PRN PRINTER 7 BIT
Parity : EVEN
4 GND IS 1 BIT STOP
5 RS 232 TX
(
* )
CRT-TERMINAL FOR EXTERNAL
6 RS 232 RX PROGRAMMING (CRT/PC TERM.)
7 GND IS
8 RS 485 LIN + (OUTWARD)
(
* )
9 RS 485 LIN - (OUTWARD) LCD-6000 REPEATERS
10 GND IS
11 RS 485 LIN + (RETURN)
12 RS 485 LIN - (RETURN)
Twisted pair
Twisted pair EIA-232 Reference
EIA-232 Reference
Receive from printer
n.c.
4 (terminal)
2 (terminal)
3 (terminal)
TO PRINTER
SIGNAL DEFINITION BE-600 A BOARD CNO
Plug the DB-25 connector into the EIA-232 port of the printer

CONNECTOR CN1 on “BE-600 A” BOARD
»NOTE :
1) If a line is programmed as Style 6 (loop line), terminals A are the OUTWARDS and terminals B are the RETURN.
2) For each line connect the shield to appropriate SC terminal.
3) Alarm and Trouble Controls : free voltage contacts.
Use to drive loads in DC only.
Alarm is activated if a detector of line 1-4 is in ALARM condition.
Trouble is activated if a detector of line 1-4 is in TROUBLE condition.
Page 7 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
TERMINAL
NUMBER DENOMINATION NOTE LINE ID. CABLE COLOUR/NUMBER
1 A1 + (1)
2 A1 -
3 B1 + (1) DETECTOR LINE 1
4 B1 -
5 SC 1 (2)
6 A2 +
7 A2 -
8 B2 + DETECTOR LINE 2
9 B2 -
10 SC 2
11 A3 +
12 A3 -
13 B3 + DETECTOR LINE 3
14 B3 -
15 SC 3
16 A4 +
17 A4 -
18 B4 + DETECTOR LINE 4
19 B4 -
20 SC 4
21 ALARM RL - N.O. (3)
22 ALARM RL - COM
23 ALARM RL - N.C. 3A
24 TROUBLE RL - N.O. 30 VDC
25 TROUBLE RL - COM
26 TROUBLE RL - N.C.

“BPS-600" BOARD for 230 V MAINS WIRING
AM-6000-60001.VP Installation Manual Page 8
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
ATTENZIONE
230 V
ATTENZIONE
230 V
LED indicating
Battery-charger operating
LED indicating Auxiliary
Power Supply operating
LED indicating
Control Panel Powered
Battery Fuse
6A
Connectors to Primary coil
(230 V Power)of
TAM6-P/TAM6-S transformers
Connector to Secondary coil of TAM6-S
transformer (auxiliary Power supply)
Connector to BE-600 A
Main Board
Jumper to connect the earth to
Panel negative Power
LED indicating main
Power Supply operating
Battery-Charger Fuse
3,15 A
Main Power Supply Fuse - 4A
Auxiliary Power Supply Fuse - 4 A
230 V Mains
Fuse 5 A
230 V Mains Input
Connector to Secondary coil of TAM6-S
transformer (Main Power supply)
= not connected
= negative connect. to the earth

WIRING THE “BE-600 A” MAIN BOARD EXTERNAL DEVICES
Page 9 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
126
1
1
12
12
RS 232 RXRS 232 RX
D.3A/200V
D.1N 4004 R.1K5 1/2WR.1K5 1/2W
RS 232 TXRS 232 TX
GND IS
General Trouble Signal
Serial Line: RS 232
CRT/PC or
LCD-6000 Repeaters
Reset Push-button N.O.
Signal Silence Push-button N.O.
SIREN
47 K End-of-line resistor
+ 24 V USER
N.B. :
Any external device powered by the
control panel or by supervised line
must be connected to a diode, as
showed in the diagram.

DETECTOR AND MODULE WIRING
Typical LOOP line (style 6)
AM-6000-60001.VP Installation Manual Page 10
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
B501 Detector Base
To employ with intelligent detectors
Separated branches to
other Loop device
- Connector CN1
> BE 600 A BOARD
> LIB 600 BOARD
SHIELD

“LIB-600" EXPANSION BOARD LAYOUT
Page 11 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
1 26
Detection Line connector Led indicating Trouble on
expansion lines
LED indicating Alarm on expansion lines
STATUS LEDs concerning
the detector lines serial
communication
Factory Code number
Product Identification
Program Eprom
Connector for earth link.
> To the BE 600 A
Main Board
Interfacing connector to :
> BE 600 A Main Board
> LIB 600 Expansion Board

CONNECTOR CN1 on “LIB-600" EXPANSION BOARD
»NOTE :
1) If a line is programmed as Style 6 (loop line), terminals A are the OUTWARDS and terminals B are the RETURN.
2) For each line connect the shield to appropriate SC terminal.
3) Alarm and Trouble Controls : free voltage contacts.
Use to drive loads in DC only.
Alarm is activated if a detector of line 1-4 is in ALARM condition.
Trouble is activated if a detector of line 1-4 is in TROUBLE condition.
AM-6000-60001.VP Installation Manual Page 12
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
TERMINAL
NUMBER DENOMINATION NOTE LINE ID. BOARDS CABLE COLOUR/NUMBER
1 A1 + (1)
2 A1 - LINE LINE LINE
3 B1 + (1) 59 13
4 B1 - BOARD BOARD BOARD
5 SC 1 (2) 12 3
6 A2 +
7 A2 - LINE LINE LINE
8 B2 + 6 10 14
9 B2 - BOARD BOARD BOARD
10 SC 2 1 2 3
11 A3 +
12 A3 - LINE LINE LINE
13 B3 + 7 11 15
14 B3 - BOARD BOARD BOARD
15 SC 3 1 2 3
16 A4 +
17 A4 - LINE LINE LINE
18 B4 + 8 12 16
19 B4 - BOARD BOARD BOARD
20 SC 4 1 2 3
21 ALARM RL - N.O. (3)
22 ALARM RL - COM
23 ALARM RL - N.C. 3A
24 TROUBLE RL - N.O. 30 V
25 TROUBLE RL - COM
26 TROUBLE RL - N.C.

“AVPS-6" AUX. POWER SUPPLY BOARD
Page 13 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
Product Identification
Connector for earth link
> to the BE 600 A Main Board
Fuse 3,15 A
Auxiliary power supply output
LED indicating the aux. power supply operating
Interfacing connector to
the BE 600 A Main Board

“DIA-6":FRONT PANEL DISPLAY and KEYPAD INTERFACE LAYOUT
AM-6000-60001.VP Installation Manual Page 14
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
LCD Display
contrast adjustment
Product Identification
Factory Code Number
Connector for keypad
Connector for BE 600 A
Main Board interconnection
WD Trouble
Reset Push-Button

ANALOG IDENTIFICATION SYSTEM COMPONENTS
DETECTOR and MODULE COMMUNICATION LINES
The AM-6000 System communicates with intelligent and addressable, monitor and control devices through a 2-wire line.
The lines can be wired to meet the requirements of an NFPA STYLE 4, STYLE 6 or STYLE 7.
The peripheral devices are powered using the same line as for data communication.
ISOLATOR MODULES
Isolator Modules (ISO-X) permit a group of devices and modules to be electrically isolated from the remainder of the
SLC Loop, allowing critical loops components to operate even in case of a short circuit of the communication line.
MONITOR MODULES
Addressable Monitor Modules (MMX), allow the AM-6000 to monitor N.O. contacts, alarm initiating devices, manual pull
stations, 4-wire conventional smoke detectors, heat detectors, water-flow and supervisory devices.
CONTROL MODULES
Through addressable Control Modules (CMX), the AM-6000 can selectively activate notification appliance circuits or
FORM-C (Voltage free contacts) output relays.
INTELLIGENT DETECTORS
The AM-6000 can communicate with intelligent ionization, photoelectric, thermal and Rate-of-Rise detectors.
LOOP INTERFACE EXPANSION BOARD (LIB 600)
The capacity of each LIB-600 board consists of up to 4 lines. Each line can support up to 99 intelligent detectors, and any
combination of max. 99 addressable pull stations, and control and monitor modules.
The AM-6000 is able to support a maximum of three LIB-600 boards for a total of 16 lines (4 lines on the main board and
12 on the 3 LIB-600 boards).
Page 15 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG

CLASS “A” WIRING CIRCUIT AND LINE ISOLATORS
Functions in accordance with NFPA STYLE 7 Signaling Line Circuit
»Note: the number of addressable devices between ISO-X modules must not exceed 25 devices.
OPERATION
By separating each group of SLC Loop devices, with a pair of ISO-X Trouble Isolator Modules , each device is protected
from opens and short circuits on all other sections.
For instance, a trouble on Section 2 will not affect Section 1 and 3.
The Isolator Modules on either side of Section 2 will open the SLC Loop. Section 1 will still operate from power on Channel
A, and Section 3 will operate from Channel B.
Since the control panel will no longer be able to communicate with the SLC Loop devices on Section 2, a trouble signal will
be generated (INVALID REPLY from Section 2 Points).
This circuit is a variation of an NFPA Style 6 Signaling Line Circuit, therefore no T-Tapping or branching is allowed.
The ratings and characteristics are the same as for the Style 6 circuit.
AM-6000-60001.VP Installation Manual Page 16
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
ISO-X Isolator Module Protected premises - Section 2 ISO-X Isolator Module
ISO-X Isolator Module ISO-X Isolator Module
Protected premises - Section 1 Protected premises - Section 3
CHANNEL A CHANNEL B
(Outward) (Return)

NOTES ABOUT LOOP WIRING
CLASS “A” WIRING
Total length of the SLC Loop pair (from the control panel output and back to the control panel) CANNOT exceed 3000
meters.
The DC Resistance of the SLC Loop pair CANNOT exceed 40 Ohm.
The measurement must be made by disconnecting Channels A and B at the control panel, shorting the two leads of Chan-
nel A together, and metering the two leads of Channel B.
Page 17 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
Channel B
Channel A
SLC LOOP
NO T-Tapping allowed
Channel B
Channel A
SHIELD

CLASS “B” WIRING
BRANCH RESISTANCE
Short the termination point of one branch at a time and measure the DC resistance, from the beginning of the channel to
the end of that particular branch.
The total DC resistance from panel to branch end CANNOT exceed 40 Ohm.
Repeat the procedure for all remaining branches.
The total of all branches on Channel B CANNOT exceed 3000 meters.
The total of all branches on Channel A CANNOT exceed 3000 meters.
AM-6000-60001.VP Installation Manual Page 18
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
Branch A
SLC Loop
Branch D
Branch B
Branch C
Branch E
SHIELDSHIELD
Channel A or B
Branch
For each channel:
Add the lenghts of all branches. The TOTAL CANNOT exceed 3000 mt.
(Branch A)+(Branch B)+(Branch C)+(Branch D)+(Branch E) < =
3000 meters
Channel B
Channel A
SHIELD