Notifier Fire Alarm Control Panel User manual

997-670-000-2
Pearl™ Fire Alarm Control
Panel Operating Manual

Contents - i
997-670-000-2
Contents
www.notierknowledge.com
Operating Manual
Contents
1 Pearl™ 2-Loop Fire Control Panel................................1-1
1.1 Introduction ........................................................... 1-1
1.2 User Interface ....................................................... 1-1
1.2.1 LCD Primary Status Indicator.................................. 1-3
1.2.1.1 Non-quiescent Status Display......................... 1-3
1.2.2 Function Keys.......................................................... 1-5
1.2.3 LED Status Indicators.............................................. 1-6
2 Fire & Fault Events - What to do......................2-1
2.1 Fire Event ............................................................. 2-1
2.1.1 What do I Need to do?............................................. 2-1
2.1.2 Log Book Entry........................................................ 2-1
2.1.3 Day MODE Operation.............................................. 2-2
2.1.4 Delays - What do I Need to do? .............................. 2-2
2.2 Fault Event............................................................ 2-3
2.2.1 What do I Need to do?............................................. 2-3
2.2.2 Log Book Entry........................................................ 2-3
2.3 RESET Key........................................................... 2-4
3 Panel Status & User Level 1 Functions ..........3-1
3.1 Status Normal ....................................................... 3-1
3.2 Panel Controls and Menus ................................... 3-1
4 Enabling User Access (Level 2).......................4-1
4.1 Passcode Entry..................................................... 4-1
4.2 Keyswitch Entry .................................................... 4-1
5 Navigating the Panel Menus ............................5-1
5.1 Disable/Enable Menu............................................ 5-2
5.1.1 Zones and Devices.................................................. 5-2
5.1.1.1 To Disable a Zone or Device........................... 5-3
5.1.1.2 Panel Disablements over a Network............... 5-3
5.1.2 Fault Relay Output................................................... 5-5
5.1.3 Fault Routing Outputs.............................................. 5-6
5.1.4 Delays to Outputs.................................................... 5-6
5.1.5 Time-of-Day Manual Override ................................. 5-7
5.2 Start/End Testing .................................................. 5-8
5.2.1 Zones....................................................................... 5-8
5.2.1.1 Testing Multiple Zones .................................... 5-9
5.2.1.2 To Cancel a Zone Walk Test ........................... 5-9
5.2.2 Auto High Test ....................................................... 5-10
5.2.3 Alarm Devices ....................................................... 5-10
5.2.4 LEDs.......................................................................5-11
5.2.5 LCD ....................................................................... 5-12
5.2.6 Internal Buzzer ...................................................... 5-13
5.3 Setting Time/Date ............................................... 5-14
5.3.1 Time....................................................................... 5-14
5.3.2 Date....................................................................... 5-14
5.4 View Status Menu............................................... 5-15
5.4.1 Historic Log............................................................ 5-15
5.4.2 Device Status ........................................................ 5-16
5.4.3 Alarm Count........................................................... 5-18

Contents - ii
997-670-000-2
Contents
www.notierknowledge.com
Operating Manual
5.5 Commissioning Menus ....................................... 5-19

Section 1 - 1
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
1.1 Introduction
This document explains how to use the Pearl™ panel’s built-in control
functions to access various menu functions and/or carry out regular
mandatory procedures required by the local re industry regulations.
Helpful descriptions and tips are also provided within this document
to assist the user in understanding the status information provided by
the Pearl™ panel’s LCD and LED indicators.
The Pearl™ Fire Alarm Control Panel has been designed to meet
the requirements of EN54-2.
1.2 User Interface
The Pearl™ re alarm control panel (hereafter referred to as the
‘panel’) is provided with all required indicators to allow the user to
review the system status and, with appropriate user (keyholder)
access, perform approved system maintenance functions in
accordance with the requirements of the local re regulations.
LCD. The panel’s user interface presents a large LCD (320 by 240
pixels) as the primary system status indicator.
See Section 1.2.1 LCD Primary Status Indicator.
Function Keys. The user interacts with the information displayed
on the panel’s LCD using the various function keys. These keys are
located in various places on the panel’s fascia: to the left, right and
below the LCD. Entering a valid access Level 2 passcode or using
the keyswitch will make these keys functionable.
See Section 1.2.2 Function Keys.
1 Pearl™ 2-Loop Fire Control Panel

Section 1 - 2
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
LEDs. System status LEDs are also provided and these are located
below the four user function keys below the LCD. These LEDs are
divided into two groups:
- Fire Zone Indicators (optional). Up to 64 zones can be indicated;
depending whether the panel is working in stand-alone mode or
as part of a network the 64 zones comprises either local zones
or network zones. In either case the maximum number of zones
managed by each panel is still 64.
- System Status LEDs. The following status indication LEDs are
provided: FIRE, FAULT, DISABLE, TEST, PRE-ALARM, SYSTEM
FAULT, DELAY ACTIVE, ALARM FAULT/DISABLED, FIRE
PROTECTION ACTIVE, FIRE PROTECTION FAULT/DISABLED,
FIRE OUTPUT ACTIVE, FIRE OUTPUT FAULT/DISABLED,
POWER, TECHNICAL ALARM, DAY MODE.
See Section 1.2.3 LED Status Indicators.
Internal Buzzer. This audible device activates to alert the keyholder
to take immediate action whenever the system detects any condition
such as a re or fault event. Depending on the type of event, the
buzzer activates (sounds) using a different tone pattern: a pulsing
tone for re events or a continous tone for faults.
The MUTE BUZZER control key is used to silence (mute) the internal
buzzer in the event of these conditions occurring. This function is
available at all access levels.
Context-sensitive Help Button. When responding to a change in
system status or when navigating the panel’s various menus, press
the context-sensitive information button ( ) at any time for guidance
and helpful tips.
ALARM
FAULT
NORMAL

Section 1 - 3
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
1.2.1 LCD Primary Status Indicator
The LCD is the panel’s primary status indicator. This allows all event
information, required to be displayed to meet the requirements of
EN54-2 for any system condition or detected event, to be displayed
on the LCD and in a clear and concise way.
When the panel is in the status Normal condition the LCD displays
the panel name or the authorised servicing company name/logo
and contact details, such as a telephone land line/mobile contact
number, etc. The panel in Status Normal mode is shown at right,
with the panel’s model name (default) displayed on the LCD.
1.2.1.1 Non-quiescent Status Display
When the system enters a re or fault condition, i.e. it is no longer in a
quiescent condition, the LCD Status Normal screen is replaced with a
display containing all the required information describing the nature
and location of the detected event. In the event that more than one
event has been detected, some of the control keys (keyholder access
only) can be used to scroll down the list of all current events to review
those ‘hidden’ from view (not all events are required by EN54-2 to
be displayed at user access Level 1, only the rst and last event).
FIRE EVENT
If the detected alarm event is from a loop device the rst zone in
alarm, the latest zone in alarm and the time each zone went into the
re condition is displayed. Also, the total number of zones in alarm is
given. For re events, the information on the LCD is supported by the
lighting of the appropriate zone re LED (if tted) and the FIRE LED.
The buzzer pulses and the MUTE BUZZER function key ashes.
An example of a typical re indication is provided at right. Press the
key to display details of the device that raised the alarm. See
Section 2.1.1 What do I Need to do? for details on how to proceed
when a re condition has been detected.
Fire Tab
Fire Summary information area:
Total re zone(s).
First re zone and latest re zone.
Time of rst /latest re zone event(s)
View options
area:
Lists every Fire;
Lists Zone(s) in
Fire.

Section 1 - 4
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
FAULT EVENT
If the panel detects a fault, the Status Normal screen on the LCD is
replaced by a fault summary screen, the buzzer sounds in steady
mode, the FAULT LED pulses and the MUTE BUZZER function key
ashes.
In this mode some of the function keys become available (see
Section 1.2.2 Function Keys) at access Level 1, to allow any user to
review details of the nature of the fault event(s). The general FAULT
LED ashes and any other applicable fault LED(s) illuminate. Fault
LED indications for individual zones are not provided.
Note: The LCD backlight is turned off and pushbutton backlights are
dimmed with the loss of the primary power, i.e. mains supply.
Pressing any button turns on the LCD backlight again to the
congured brightness setting; pushbuttons backlights remain
dimmed until primary power is restored.
An example of a typical LCD fault display is provided at right. See
Section 2.2.1 What do I Need to do? for details on what to do when
a fault condition has been detected.
Fault Tab
View options
area:
Lists every Fault;
Lists ‘Zones in
Fault’.
Fault summary information area, which includes:
Total individual faults, detection zones in fault and wiring loops in fault.
General Fault LED (pulsing)

Section 1 - 5
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
1.2.2 Function Keys
Panel operation, at user access Levels 1 and 2, is controlled by the
various function keys located on the front fascia.
The group of keys to the right of the LCD provide the following user
functions:
1. Function Control Keys.
These are single-function activation keys and, apart from the
MUTE BUZZER and CHANGE TAB keys, require the panel to be
at user access Level 2 before they can be selected, for example
the EXTEND DELAY function during the rst stage of an active two-
stage delay period.
2. Menu Navigation/option Selection Functions Keys.
With the panel at user access Level 2 these keys, in association
with the alphanumeric keypad, are now functional.
3. Alphanumeric Keys
These keys are available when the panel is at user access Level 2
and the user menus are available. Menu options can be selected
using these keys, as an alternative method to the or
navigation and keys.
4. Other Function Keys
These are located to the left and below the LCD and comprise the
following:
a. Show More Zones in Fire key
b. Change Tabs key
c. Four user (programmable) Function keys.

Section 1 - 6
www.notierknowledge.com
997-670-000-2
Panel User Interface
Operating Manual
1.2.3 LED Status Indicators
In addition to details of detected events being displayed on the LCD,
a number of LED status indicators are provided in the lower area
of the panel fascia.
The upper two banks of LEDs are zone re LEDs (zones 1 to 64)
and may not be tted.
The lower bank of LEDs contains all the required system status
indicators to support the primary indicator, i.e. the LCD. With most
panel- or loop-related events these LEDs are able to provide a quick
indication of the possible cause of the panel status change.
The following status indicators are provided:
LED Name Colour Description
FIRE Red A re condition exists.
FAULT Yellow A fault condition exists.
DISABLE Yellow One or more devices are disabled.
TEST Yellow A test condition has been entered,
PRE-ALARM Yellow A pre-alarm condition exists.
SYSTEM FAULT Yellow The system has failed.
DELAY ACTIVE Yellow Programmed delay(s) are in effect.
ALARM FAULT/DISABLED Yellow A re output, if congured, is disabled or has a fault.
FIRE PROTECTION ACTIVE Red An output to the re protection system, if congured, is active.
FIRE PROTECTION FAULT/DISABLED Yellow An output to the re protection system, if congured, is disabled or has a fault.
FIRE OUTPUT ACTIVE Red The re relay (and re output if congured) is active.
FIRE OUTPUT FAULT/DISABLED Yellow The re relay is disabled or the Fire output (if congured) is disabled or has a fault.
POWER Green System power (mains or battery) is available.
TECHNICAL ALARM Yellow Technical Alarm device activated.
DAY MODE Yellow The DAY MODE has been entered.

Section 2 - 1
www.notierknowledge.com
997-670-000-2
Fire and Fault Events - What to do
Operating Manual
2 Fire & Fault Events - What to do
2.1 Fire Event
If the panel enters the alarm state, i.e. a Fire condition has been
detected, the following visual and audible indications are given:
- TheLCDdisplaysinformationaboutthereevent,suchasrst
andlatestzoneandrstdeviceinalarm.AFireTabisdisplayed
at the bottom left-hand corner of the LCD.
- The appropriate zone(s) LED lights
- The General FIRE LED (red) lights (not with First Fire condition)
- The internal buzzer operates (pulsing tone)
Anyoutputsprogrammedtooperateimmediately,includingsounder
devices, are activated.
2.1.1 What do I Need to do?
Press the MUTE BUZZER key to silence the panel’s internal buzzer.
This is the only key action able to be performed at user access Level
1.InsomecasestheENDDELAYkeyfunctionisselectableatuser
accessLevel1,butonlyifthisfunctionwasconguredduringsystem
commissioning.
Use the information provided by the LCD and the LEDs to understand
quickly what action needs to be taken. To assist this process, the
panel’sLCDindicatesthezonelocation(s)ofthereevent(s)and
the device(s) responsible for the alarm condition. Use the information
providedtoidentifythegeographicsourceoftherealarm.
2.1.2 Log Book Entry
Enter information about the fire alarm in the log book. Ensure the
entry contains the relevant information, date and keyholder’s name/
signature.Informationaboutthealarmeventisalsostoredinthere
control panel’s event log and can be accessed by the service engineer.
The following user level control keys are available:
AccessLevel1:
- MUTE BUZZER
- CHANGETAB
- ENDDELAY(ifconguredduringcommissioning).
AccessLevel2:
- MUTE BUZZER
- CHANGETAB
- ENDDELAYandEXTENDDELAY
- SILENCEALARMS
Also,the ,, and keys and numeric keypad are available.
When backlit, the Information key( ) is available and its selection
provides helpful, context-related help. The and the keys are
selectable in alarm without a keyswitch operation or a request for
a passcode entry.

Section 2 - 2
www.notierknowledge.com
997-670-000-2
Fire and Fault Events - What to do
Operating Manual
2.1.3 Day Mode Operation
IfaDayModeprogramhasbeenconguredandiscurrentlyactive
(theDAYMODELEDislit),thesensitivityofsensorswillbechanged
automatically as congured when the panel was commissioned.
In most cases the sensitivity of sensors is reduced to avoid the
incidence of false alarms when the building is occupied. In the event
arealreconditionisdetectedthepanelrespondsinthenormal
waybutafterashortalarmconditionvericationperiod.Attheend
ofthisvericationperiodactivationoftherequiredoutputs,suchas
ringingthealarmbellsandcallingtherebrigade,occurs.
Note: The authorised person (key holder) needs to have been made
awarethatthepanelhasbeenconguredthatsuchadelayis
imposedbeforeafullreconditionisindicatedbythepanel.
2.1.4 Delays - What do I Need to do?
Ifthepanelhasbeenconguredtodelaytheoperationofsounders,
etc.the detectionofa remayindicate azonerecondition but
withouttheFIRELEDbeinglit.Thisindicatesthatarecondition
has been detected, but the panel is waiting for another device to
enterthereconditionbeforeareisfullyrecognised.Thecondition
ofhavingmorethanonereindicationbeforeactivatingoutputsis
known as coincidence.
Itisalsopossiblethatthepanelhasbeenconguredtodelaythe
activation of any outputs when a re has been detected. In this
case,adetectedrealarmconditionstartstherstoftwocongured
timers allowing the authorised person (key holder) a reasonable
period in which to react to permit the delay to be extended, thereby
allowing a proper search to be conducted. This is achieved using the
EXTENDDELAYkey(onlyavailableatuseraccessLevel2).The
secondtimerperiod,normallysettobelongerthantherstperiod,
startsitscountdown;thersttimerhasnowbeenoverridenbythe
secondtimer.PresstheENDDELAYkey(canbeavailableatuser
accessLevel1)toendanydelaysandenablethefullrecondition
to be entered.
EXTENDDELAYkey
ENDDELAYkey
KEYSWITCH
(toenableuserAccessLevel2)
DAYMODELED

Section 2 - 3
www.notierknowledge.com
997-670-000-2
Fire and Fault Events - What to do
Operating Manual
2.2 Fault Event
If the panel enters a fault state, i.e. a fault condition has been
detected, the following visual and audible indications are given:
- The LCD displays information about the fault event, such as panel
condition or zone and device information.
- TheGeneralFAULTLED(yellow)lights
- The internal buzzer operates (continuous tone)
- TheSYSTEMFAULTLEDorotherFAULTLED(s)maylight
Inaddition,anyconguredfaultroutingoutputsareactivated.
2.2.1 What do I Need to do?
Press the MUTE BUZZER key to silence the panel’s internal buzzer.
This is the only action performed by this control key.
Use the information provided by the LCD and the LEDs to for guidance
on the action that needs to be taken. To assist this process, the panel’s
LCD indicates the nature of the fault; if it is a faulty detection device
the zone location and the device(s) responsible for raising the fault
indication may be accessed using those control keys enabled at
accessLevel1.Selectablekeysarebacklittoconrmthisstate.
Using the information provided, identify the type and location of the
fault event so that effective action may be taken to resolve it or, if
this is not possible, seek assistance from the authorised servicing
company.
2.2.2 Log Book Entry
Enter information about the fault in the log book. Ensure the entry
contains the relevant fault information, date and keyholder’s name/
signature.Informationaboutthe faulteventisalsostored inthere
control panel’s event log and can be accessed by the service engineer.
GENERALFAULT
SYSTEMFAULT
FIREPROTECTIONFAULT/DISABLED
ALARMDEVICESFAULT/DISABLED
FIREOUTPUTFAULT/DISABLED
FAULT LED INDICATIONS

Section 2 - 4
www.notierknowledge.com
997-670-000-2
Fire and Fault Events - What to do
Operating Manual
1
4
7
2
5
8
0
3
6
9
c
ABC DEF
GHI JKL
TUV WXYZ
MNO
PQRS
2.3 RESET Key
TheRESETkeyisusedtoclearallreandfaultstatusindications
on the panel and return it to its normal condition.
Note: The RESET key must not be used to clear re or fault
indications without the appropriate actions having been taken
to investigate and remedy the cause of any such events.
TheRESETkeycanonlyclearreorfaulteventindicationswhen
they have been satisfactorily removed from the system.
To perform a reset action, either insert the key and turn through 90° in
a clockwise direction or enter a valid user access Level 2 passcode
and then press the RESET key. The LCD will re-display the Status
Normal screen and all alarm or other event-related indicators will
be extinguished.
After pressing the RESET key any conditions still present in the
system will, once again, cause the panel to display and indicate the
existence of such events until they have been satisfactorily remedied.
The POWER LED does not extinguish.
MUTE BUZZER
EXTEND DELAY
END DELAY
RESET
DISABLE FIRE OUTPUT
DISABLE ALARMS
DISABLE FIRE PROTECTION
SILENCE ALARMS
SOUND ALARMS
RESET key
KEYSWITCH
(to enable user access Level 2)
Non-
quiescent
Condition
Remove the access Level 2 entry key or, if a passcode was used,
press the key until the Status Normal screen appears. When the
Status Normal screen re-appears, the panel has been returned to
access Level 1.

Section 3 - 1
www.notierknowledge.com
997-670-000-2
Panel Status & User Level 1 Functions
Operating Manual
3 Panel Status & User Level 1 Functions
3.1 Status Normal
The following control keys function at user access Level 1:
- MUTE BUZZER
- CHANGE TABS .
With the panel at user access Level 1 and also in the quiescent state,
i.e. the panel status is normal, the following indications are present:
- LCD. This displays the ‘Status Normal’ screen - no user menus
are shown but the panel name or authorised servicing company
information/logo is displayed.
- POWER LED (green). This is lit continuously when the panel is
powered.
No other front panel LEDs are lit and the internal buzzer is silent.
3.2 Panel Controls and Menus
No control functions or menus are available to the user at access
Level 1, except the key to display the user level passcode entry
screen. To enable the panel control keys and gain access to the user
level menus requires entry of a valid Level 2 passcode or to insert
and turn the key (clockwise) in the keyswitch.
Refer to Section 4 Enabling user Access (Level 2) for more details.
Access to the commissioning menus requires the entry of a
commissioning engineer’s passcode - details of this function are
not provided in this document.

Section 4 - 1
www.notierknowledge.com
997-670-000-2
Enabling User Access (Level 2)
Operating Manual
4 Enabling User Access (Level 2)
4.1 Passcode Entry
With the Status Normal screen displayed on the LCD, pressing the
key will present the user access level passcode request entry
screen.
Entry of a valid passcode enables the user to access the appropriate
panel menus. Which menu is displayed next depends upon the
access passcode entered: user or commissioning level.
To enter the access Level 2 passode make sure that ‘Standard
User’ is highlighted and then press the key. The screen now
presents the user with a passcode entry eld. Using the numeric
keypad enter the appropriate access passcode and press the
key again to enter.
A correct passcode entry displays the main user level menu (Main
Menu).
Press the key to abandon an invalidated passcode entry attempt
and re-try the passcode entry. Press the key and repeat the
process above.
4.2 Keyswitch Entry
Similarly, inserting the access entry key into the keyswitch and
turning it clockwise through 90° will display the access Level 2 Main
Menu. The MENU tab at the bottom of the screen conrms this.
Note: The MENU tab is also present when the passcode entry
screen is displayed.
Note: In the unlikely event that the required user access passcode
has been forgotten and the key has been misplaced, contact
the servicing company for assistance. You will asked to quote
the code displayed when the key is pressed. No other
method is available to access the menus in this situation.
1
2

Section 5 - 1
www.notierknowledge.com
997-670-000-2
Navigating the Panel Menus
Operating Manual
5 Navigating the Panel Menus
Once access to the user access Level 2 menus is obtained (see
Section 4 Enabling User Access (Level 2), selection of menu
options is very simple to do.
With a menu option highlighted press the or key to select.
Alternatively, use the numeric keypad and press the number of the
desired menu option to select that function. By default, when rst
displayed the rst available menu option is highlighted.
With the Main Menu all the listed options are available and the rst
is highlighted.
Working Example - Set/Change the Date/Time
With the Main Menu displayed on the LCD, press the numeric key
‘3’ to select the ‘Set Clock’ option.
Alternatively, use the key to move the highlight down to option 3
and press either the or key to select the Set Clock function.
The function is cyclic, so if you overshoot the desired option just
try again using the same key.
See Section 5.3 Setting Time/Date for more details on how to set/
change the time and date.
OR
If the panel is part of a network you will be prompted to enter the node
ID (number) of the panel when accessing many of the user menus
described in this section.
OR

Section 5 - 2
www.notierknowledge.com
997-670-000-2
Navigating the Panel Menus
Operating Manual
5.1 Disable/ Enable Menu
The Disable/Enable function is available from the user access Level
2 Main Menu. Enter the user access Level 2 passcode or insert the
key and turn clockwise through 90° to display the Main Menu. The
MENU tab is also displayed once the Main Menu is accessed.
With menu option 1: Disable/Enable highlighted, press the or
key or, using the numeric keypad, press the ‘1’ key to access
the Disable/Enable menu.
The following disable/enable functions are available:
- Zones and Devices (full disablement/enablement)
- Fault Outputs
- Delays to Outputs (if congured during commissioning)
- Time-of-Day Manual Override (if configured during
commissioning).
5.1.1 Zones and Devices
Select option 1: Zones and Devices to disable/enable a zone or
select devices to disable individually. Only congured zones are
displayed; if a zone has not been congured it will not appear in the
list of zones.
Zones may be fully or partially disabled. A zone only requires one
device to be disabled for its state to change to ‘partially disabled’.
When the congured zones are displayed the enabled/disabled status
of each is given. In the nearest example at right, all zones are shown
as fully enabled, i.e. no individual devices have been disabled on
these two zones. The furthest screen shows that zone 4 is partially
disabled, with the ‘DISABLE’ tab also displayed - the DISABLE LED
will also be lit.
With the desired zone highlighted, pressing the key displays the
zone devices and their individual enabled/disabled states.
OR
OR

Section 5 - 3
www.notierknowledge.com
997-670-000-2
Navigating the Panel Menus
Operating Manual
OR
5.1.1.1 To Disable a Zone or Device
This description is for a panel working in stand-alone mode.
Performing disablements over a network is described after this.
1Use the or navigation buttons to highlight the zone to
be disabled/enabled and then press the key to change its
state. The user is now given the choice of disabling/enabling ALL
the zone alarms inputs (highlighted by default) or individual
devices for the selected zone. In the example opposite, zone 4
was selected and all the devices in that zone are listed together
with an indication of their individual current enabled/disabled
state - in this case all devices are ‘Enabled’.
Note: Devices that are not zone alarm inputs can be disabled
individually. However, zone output devices, such as sounders,
cannot be disabled individually.
2To disable/enable the entire zone (default selection) press the key.
Each press of the key toggles the state of the zone: disabled
or enabled. After disabling a zone or device(s), press the key
to display the ‘DISABLE’ tab and view the disabled devices.
However, if the toggle function is used for a part-disabled zone
then, depending on whether any devices are not zone alarm inputs,
the ‘part-disabled’ state is retained, even though the key has
been pressed to toggle the state.Also, with any device in the list
highlighted pressing the key toggles its ‘enabled/disabled’ state.
5.1.1.2 Panel Disablements over a Network
When disabling a zone on a network you will be prompted to enter a
panel ID number before the zone selection can be made. Enter the
panel ID number and then make the zone or device selection as for
a stand-alone panel (see above).
With any active disablements all the panels on the network display
the DISABLE tab with all the disabled devices listed.

Section 5 - 4
www.notierknowledge.com
997-670-000-2
Navigating the Panel Menus
Operating Manual
Working Example - Disable Zone 3
With the Main Menu displayed on the LCD, press the numeric key
‘1’ to select the ‘Disable/Enable’ option.
Press the ‘1’ key on the numeric keypad to select ‘Zones and Devices’.
The list of all congured zones is displayed, the rst zone in the list is
highlighted. Use the key to select another zone for disablement,
in this case zone 2.
Press the key to change the status of the selected zone, i.e.
disable or enable depending on its current status.
OR

Section 5 - 5
www.notierknowledge.com
997-670-000-2
Navigating the Panel Menus
Operating Manual
5.1.2 Fault Relay Output
Select option 2: Fault Relay to enable/disable the fault relay output.
To enable/disable the fault relay output press the key. Each time
the key is pressed the enable/disable state is changed.
With the fault relay output in a disabled state, the DISABLE LED is lit.
The DISABLE tab is displayed with disabled fault relay output.
Press the key to bring the DISABLE tab to the front and display
details about this disablement.
Press the key again to bring the MENU tab to the front. Press
the key at any time to exit.
Note: Fault relay output state change remains until the menu option
is again accessed and the state toggled as described above.