Notifier NBG-12LX User manual

NORMAL
ACTIV
A
TED
4 3 2 1
00
10
11
12
13
14 15 11
22
33
44
TENS ONES
66
77
88
99
55
UL Approved Label Here
1234567890123
1
23456789012
3
1
23456789012
3
1
23456789012
3
1234567890123
ADDRESS
LOOP
01
2
3
4
5
6
7
8
9
01
2
3
4
5
6
7
8
9
10
11
12
13
14 15
LED OPERATION
Alarm:
Steady RED
Normal CLIP Systems:
Flash RED
Normal FlashScanTM:
Flash GREEN
Note: LED is visible
through translucent
handle.
Setting the NBG-12LX Address
The NBG-12LX Addressable pull station is factory preset with
address 00  Set the address for the pull station by turning the
rotary address switches on the addressable module mounted inside
the pull station Only one device per address is allowed Multiple
modules may not be set to the same address on the Signaling Line
Circuit Once the address is set, record it in the space provided on
the product ID label located inside the pull station
NBG-12LX Addressable Pull Station
Description
The NBG-12LX Addressable pull station is a non-coded, dual-
action manual pull station with a key-lock reset feature It
provides NOTIFIER intelligent control panels with one addres-
sable alarm initiating input The addressable module is housed
inside the pull station The NBG-12LX is compatible with all
Notifier intelligent panels and will automatically operate in either
FlashScan or CLIP (Classic Loop Interface Protocol) mode
FlashScan is a patented (U S Pat No 5,539,389) High Speed
Communications Protocol Refer to the FACP Installation
Manual to determine if FlashScan protocol is supported
FlashScan or CLIP operating mode must be selected in the
FACP (This selection is not available or required in FACPs that
do not support FlashScan, therefore CLIP mode is enabled
by default ) No selection is required in the Pull Station The
NBG-12LX meets the ADA requirement for a 5-lb maximum
pull force to activate the pull station Operating instructions are
molded into the pull station handle along with Braille text
Molded Terminal numbers are also present
Ratings
Normal Operating Voltage: 24 VDC
Average Operating Current (LED Flash): 300 µA
Temperature Range: 32o F - 120o F (0o C - 49o C)
Relative Humidity Range: 10% - 93% non-condensing
Document 51093 Revision A2 ECN 01-293 09/14/01
Installation
The NBG-12LX Addressable pull station can be surface mounted
to a NOTIFIER SB-10 surface backbox or semi-flush mounted
on a standard single-gang, double-gang or 4 (10 16 cm) square
electrical box The optional BG-TR trim ring can be used if the
NBG-12LX is to be semi-flush mounted
So tware Note or AM2020/AFP1010 Programming
The NBG-12LX is an Alarm Initiating Module of software type
mpul If you have an older system that does not support the mpul
software type, the software type mon may be used
I , during mounting o the pull station, the door becomes de-
tached, complete the following steps to reattach the door to the
backplate The door cannot be connected to the pull station if the
unit is mounted to the backbox
1) Position the door and backplate side by side in the full open
position (i e 180-degrees with respect to each other )
2) With the backplate position fixed, move the door behind the
backplate, as shown in the illustration, part A
3) Align the hinge posts and holes by bringing the door up to
meet the backplate, paying particular attention to the keying
that occurs when the doors post hole is aligned to the
backplates hinge post Refer to the illustration, part B
4) With the two pieces aligned and keyed together, slide the holes
down onto the posts Refer to the illustration, part C
5) Holding the backplate, close the door slightly to lock the door
and backplate together
To use the NBG-12LX
with panels capable of
supporting up to 159
addresses, pry off the
break-away address
block using a flat-
bladed screwdriver.
The break-away piece
is illustrated below.
ROTARY ADDRESS SWITCHES
LED
LO OP
NO TIFIER
NBG - 12 Series
NO N -C O D ED
FI RE A LAR M B OX
LI STED
23424
REFER TO D OCUMENT
Made in
U. S. A.
M
AD DR ES S
L
U
PRODUCT IDENTIFICATION LABEL
rot switch 9-13.cdr, label_1.cdr, rotary box.cdr
NBG12-Face2.cdr
www.PDF-Zoo.com
firealarmresources.com

P/N 50997 REV.
REFER TO DOCUMENT
NUMBER 51015 REV.
L OOP ADDRESS



!
P/N 50997 REV.
REFER TO DOCUME NT
NUMBER 51015 REV.
LOOP AD DRE SS



!
"
'
+
*
)
POST
DOOR KEYS INTO
BACKPLATE AT THIS POINT
POST
POST
HOLE
HOLE
Operation
Push in and pull down the handle where indicated to activate the station The NBG-12LX manual fire alarm pull
station includes one SPST (Single Pole, Single Throw) N/O (normally-open) switch and the addressable module
located inside the station Pushing in and pulling down the dual action handle causes the N/O alarm switch to close
The word ACTIVATED is displayed on the top of the handle when the pull station handle is pushed in and pulled
down The activated handle can not be reset without employing the key-lock reset To reset the NBG-12LX pull
station: 1) Insert the key and turn counterclockwise, 2) Open the door until the handle moves back into the
NORMAL position, 3) Close the door and lock it Closing the door automatically resets the switch to the
NORMAL position
ACTIVATED
NBG 12LX PULL
STATION
CAUTION!
Install the Notifier NBG-12LX manual pull
station in accordance with these instructions,
applicable NFPA standards, national and
local Fire and Electrical codes and the re-
quirements of the AHJ (Authority Having
Jurisdiction) Regular testing of the devices
should be conducted in accordance with the
appropriate NFPA standards Failure to fol-
low these directions may result in failure of
the device to report an alarm condition
Notifier is not responsible for devices that
have been improperly installed, tested or
maintained
For ADA compliance, if the clear floor
space only allows forward approach to an
object, the maximum forward reach height
allowed is 48 in (1,220 mm) If the clear
floor space allows parallel approach by a
person in a wheelchair, the maximum side
reach height allowed is 54 in (1,370 mm)
Document 51093 Revision A2 ECN 01-293 09/14/01
Note - Opening the pull station
door will not activate or deac-
tivate the alarm switch.
DOOR ATTACHMENT
DOOR MATED TO BACKPLATE
STRIP GAUGE
 !"
7 5 2 ) 6 """''
With the door and
backplate aligned and
keyed together, slide
the holes down onto
the posts.
Closing the door slightly
locks the door and
backplate together.
1) If semi-flush mounting, proceed to step 4
2) Mount the backbox before wiring to the pull station
3) Before mounting the station, pull all necessary wiring through the backbox and
optional trim ring
4) Remove the correct amount of wire insulation The pull station backplate is
molded with a strip gauge to measure the amount of insulation to be removed
5) Connect the wiring from the addressable fire alarm control panels Signaling
Line Circuit (SLC) to Terminals 1(-) and 2(+) on the NBG-12LX addressable
pull station SLC polarity is critical for this connection
6) Connect the wiring going to the next device on the SLC to Terminals 1 and 2,
again being certain to observe polarity
7) If using a single-gang or SB-10 box for mounting, open the pull station door;
align the mounting holes of the pull station backplate to the backbox and screw
into place Tighten both top and bottom screws
8) Set the address as described in Setting the NBG-12LX Address and write the
address in the space provided on the label
9) Close and lock the pull station door
Wiring
12LXWiring.cdr
12LXDoorMount.cdr
NBG12-Active.wmf
www.PDF-Zoo.com
firealarmresources.com