Novus NVR-6204P4-H1-II User manual

Quick start guide
NVR-6204P4-H1-II
NVR-6208P8-H1-II

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
2
CAUTIONS AND WARNINGS
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:
Exclusion of liability in the event of damage to data contained on disks or other devices or media:
The manufacturer is not liable in the event of damage or loss of data contained on disks or other
devices or carriers during the operation of the Product.
Obligation to consult the Manufacturer before performing any action not provided for in the
instruction manual or other documents:
Before performing an action that is not provided for a given Product in the user manual, other
documents attached to the Product or does not result from the normal purpose of the Product, it is
necessary, under pain of exclusion of the Manufacturer's liability for the consequences of such action,
to contact the Manufacturer.
Pictures in this publication showing camera views can be simulations. Actual camera
images may vary depending on the type, model, settings, observation area, or
environmental conditions.
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonization of the laws of the Member States
relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes).
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on waste electrical and electronic equipment WEEE)
(OJ L 197, 24.7.2012, p. 38–71, with changes).
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes).
COMMISION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending
Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards
the list of restricted substances.
DIRECTIVE (EU) 2017/2102 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 15 November 2017 amending Directive 2011/65/EU on the restriction of the
use of certain hazardous substances in electrical and electronic equipment.
DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT
AND OF THE COUNCIL of 26 February 2014 on the harmonisation
of the laws of the Member States relating to the making available on the market of electrical
equipment designed for use within certain voltage limits.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
3
SAFETY REQUIREMENTS
1. Please read this manual carefully before installation and operation;
2. Please keep this manual for the lifespan of the device in case referring to the contents of this
manual is necessary;
3. It is necessary to comply with the safety requirements described in the manual, as they have
adirect impact on the safety of users and the durability and reliability of the device;
4. All activities performed by installers and users must be carried out as described in the manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. It is not allowed to use any additional devices, components or accessories not provided for and not
recommended by the manufacturer;
7. Do not install this device in places where proper ventilation cannot be provided (e.g. closed
cabinets, etc.), as this may cause heat build-up and may result in damage;
8. Do not place the device on unstable surfaces. Installation must be carried out by qualified
personnel with appropriate permissions in accordance with the recommendations provided in this
manual;
9. The device may be powered only from sources with parameters compliant with those indicated
by the manufacturer in the technical data;
Before using the device, read the instruction manual in order to ensure proper and safe operation
of the device. Failure to comply with the instructions may lead to damage to the device and/or
safety violations.
The user may not repair the device himself. Repairs and maintenance of the device may only be
performed by qualified service personnel.
The device, which is an element of a professional CCTV system used for supervision and
control, is not intended for self-assembly in households by persons without specialist
knowledge.
As the product is constantly improved and optimised, some of its parameters and functions may have
changed from those described in this manual. If in doubt, please refer to the user manual at
www.novuscctv.com
The user manual located at www.novuscctv.com is always the most up-to-date version.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
4
FOREWORD INFORMATION
1. FOREWORD INFORMATION
1.1. Main characteristics
• Network Video Recorder for 4 / 8 IP cameras.
• 1 x Fast Ethernet port.
• 4 / 8 PoE ports working in the 802.3af/at standard with the option of Extended mode
• Recording resolution up to 3072 x 2048.
• H.264, H.265, H.265+, H.265 Smart compression.
• Recording stream up to 40 / 64 Mbps in total from all cameras.
• ONVIF protocol support.
• Dual stream recording
• Support 1 x SATA 3,5” HDDs. *
• Operating system based on Linux.
• Main monitor 1 x HDMI (FullHD), 1 x VGA (FullHD).
• Intelligent Image Analysis (Exception, Scene Change, Video Blurred, Video Color Cast, Tripwire,
Zone entrance, Abandoned Object, Object Disappearance, Crowd detection, Face Detection, Cross
Counting, Analysis of Recognized Number Plate Numbers (LPR), Fire detection, Temperature
measurement, Video metadata) **.
• Possibility to get video streams from another Novus 6000 series recorder.
• Backup: onto HDD or USB Flash Memory through USB port and through the IP network.
• Software: N Control 6000 (application for remote administration, live monitoring and recorded data
search).
• SuperLive Plus application for live and playback functions from mobile devices.
• User friendly multi-lingual OSD.
• The device can be operated with a USB computer mouse and remote control.
• Power supply: 48 VDC (100 ~ 240 VAC/48 VDC PSU in-set included).
*List of compatible HDD models and maximum capacities is available on the product website
www.novuscctv.pl in the DOWNLOADABLE FILES tab in the "HDD Compatible disks" file.
** Functions depend on connected camera model.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
5
FOREWORD INFORMATION
1.2. Recorders’ technical data
*** With dualstream mode.
NVR-6204P4-H1-II NVR-6208P8-H1-II
Video
IP Cameras up to 4 channels at 3072 x 2048 resolution
(video + audio)
up to 8 channels at 3072 x 2048 resolution
(video + audio)
Maximum Supported
Camera Resolution 3072 x 2048
Compression H.264, H.265, H.265+, H.265 Smart
Monitor Output main (split screen, full screen, sequence): 1 x HDMI, 1 x VGA
(up to 2 monitors simultaneously)
Dualstreaming Support yes
Fisheye Support yes, 6000 IP series cameras
using any web browser, N-VID6, N Control 6000
Audio
Audio Input/Output - / 1 x HDMI
Recording
Stream Size 40 Mb/s in total from all cameras 64 Mb/s in total from all cameras
Recording Mode continuous, triggered by: manual, alarm input, motion detection, intelligent image
analysis functions
Prealarm/Postalarm up to 5 s/up to 600 s
Display
Display Speed 120 fps (4 x 30 fps) *** 240 fps (8 x 30 fps) ***
Playback
Playback Speed 120 fps (4 x 30 fps) *** 240 fps (8 x 30 fps) ***
Recorded Data Search by date/time, events, image analysis events, POS, motion in a defined area, tags,
license plate number
Backup
Backup Methods USB port (HDD or Flash memory), network
Backup File Format AVI, RPAS (player included)
Storage
Internal Storage available mount: 1 x HDD 3.5” 10 TB SATA
Total Internal Capacity 10 TB
Alarm
Camera Alarm Input/
Output supports IP camera’s alarm input/output
Motion Detection supports camera’s motion detection
System Reaction to
Alarm Events
buzzer, alarm output activation, recording activation, PTZ, e-mail with atatchment,
Full Screen, PUSH message, voice prompt, snapshot
Intelligent image analysis
Supported Functions
Exception, Scene Change, Video Blurred, Video Color Cast, Tripwire, Zone entrance,
Abandoned Object, Object Disappearance, Crowd detection, Face Detection, Cross
Counting, Analysis of Recognized Number Plate Numbers (LPR), Fire detection,
Temperature measurement, Video metadata
Database Capacity 1000 license plates

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
6
FOREWORD INFORMATION
The availability of individual functions (including image analysis) depends on the model of the
cameras used, as well as the software version of the recorder and cameras.
Presented display and playback speeds are achieved using dual-streaming. Detailed data on hard drives
can be found at www.novuscctv.com in the compatibility table available in the DOWNLOADABLE
FILES tab.
1.3. Package contents
Unpack the device carefully. After unpacking, please ensure that package contains the following items:
• Digital Video Recorder
• Power supply 100~240 VAC/48 VDC
• USB Mouse
• IR remote controller
• Quick start guide
• Screws for screwing the hard disk
NVR-6204P4-H1-II NVR-6208P8-H1-II
Network
Network Interface
1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
4 x Ethernet PoE (IEEE802.3af/at, Class 4) -
RJ-45 interface, 10/100 Mbit/s, with Exten-
ded mode
1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
8 x Ethernet PoE (IEEE802.3af/at, Class 4) -
RJ-45 interface, 10/100 Mbit/s, with Exten-
ded mode
Network Protocols
Support
HTTP, TCP/IP, IPv4/v6, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP, UPnP, SNMP,
IEEE 802.1X, PPPoE, SMTP, P2P, POS, HTML5
ONVIF Protocol
Support Profile S (ONVIF 2.2 or higher)
PC/MAC Software NMS, Internet Explorer, Firefox, Chrome, Opera, N Control 6000, Edge/Safari,
N Control 6000
Mobile applications SuperLive Plus (iPhone, Android)
Number of Simulta-
neous Connections
up to 64 clients, up to 8 main streams or 64
substreams or 4 playback streams in total
up to 64 clients, up to 12 main streams or 64
substreams or 8 playback streams in total
Bandwidth 40 Mb/s in total to all client workstations 64 Mb/s in total to all client workstations
PTZ
PTZ Functions pan/tilt/zoom, preset commands
Auxiliary Interfaces
USB Ports 2 x USB 2.0
Operating system
Operating System Linux
OSD languages: Polish, English, others
Control PC mouse and IR remote controller (in-set included), network
System Diagnostic automatic control of: HDDs, network, camera connection loss
Security password protection, IP filtering, MAC filtering, ARP guard
Installation parameters
Dimensions (mm) 255 (W) x 42 (H) x 233 (D)
Weight 0.8 kg (without HDD) 0.84 kg (without HDD)
Power Supply 48 VDC (100 ~ 240 VAC/48 VDC PSU in-set included)
Power Consumption 15 W (with 1 HDD) + 40 W PoE 15 W (with 1 HDD) + 72 W PoE
Operating Temperature -10°C ~ 50°C

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
7
STARTING THE DEVICE
If any of the elements has been damaged during transport, pack all the elements back into the original
packaging and contact your supplier.
NOTE!
ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible
with the "PROFILE S".
Implementation of the ONVIF protocol by different manufacturers may vary by some functions,
which can make them work improperly or not in accordance with expectation. AAT SYSTEMY
BEZPIECZEŃSTWA SP. Z O.O. company is not responsible for incompatibility problems
resulting from cameras of other brands than NOVUS, which are using ONVIF protocol. If you
are using ONVIF protocol cameras other than NOVUS brand it is recommended to test each
time whether required functions work correctly.
2. STARTING THE DEVICE
2.1 Electrical connection and other back panel elements.
NVR-6204P4-H1-II
NVR-6208P8-H1-II
1. DC48V: Recorder power supply connection socket
2. PoE PORTS: RJ-45 ethernet ports to connect PoE IP cameras.
3. USB: USB 2.0 ports for mouse, external Flash memory and other USB devices.
4. HDMI: Main monitor connector, use the HDMI cable to connect monitor.
5. VGA: Main monitor connector, use the D-SUB VGA cable to connect monitor.
6. LAN: RJ-45 connector port to connect to the local network and internet.
1 1 3 4 5 6
5
4 3 2 1
6

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
8
STARTING THE DEVICE
2.2 HDD mounting
NVR-6204P4-H1-II and NVR-6208P8-H1-II support 1 internal SATA HDD.
NOTE!
In order to find information regarding the compatible models of HDDs and their maximum
capacities, please contact Novus distributor or check the information presented at
www.novuscctv.com. AAT HOLDING Company is not responsible for any problems from using
not recommended hard drives.
The list of compatible HDDs contains all the HDDs that can be used with a given DVR including
HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of
the recording process and data safety are paramount factors of any CCTV system, we strongly
advise to use HDDs designed for continuous (24/7) operation.
You need to format disks if they were used in a different device. All data saved on HDD prior to
format will be lost.
HDD installation
NOTE!
Before removing cover unplug the power cord from the NVR. When NVR is turned on before
disconnecting the power cord, shut down the recorder using the NVR menu.
In order to mount the hard drives, after unscrewing four screws (two screws on the side of the housing)
in the places shown in the photo below, remove the recorder housing by sliding it back and then lifting
it up.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
9
STARTING THE DEVICE
After removing the case, mount the disk using mounting screws supplied in the set (4 pcs.). Then
connect the power and signal cords.
After connecting the hard drive, mount the recorder housing. Run NVR to check the correct
connections and format the hard drive.
2.3 Connecting the power supply.
To start please connect provided power cord in the rear power port of the NVR. Initialization lasts
approximately 60 seconds. During this time executing any device functions and pressing any buttons is
prohibited. To shut down the device please use the menu.
NOTE:
Make connection when the power is not applied.
Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.
However, even if it's not earth-grounded, never modify it on your own for earth-grounding.
Make sure that power adapter is placed near of NVR and secured from accidental disconnection.
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
10
STARTING THE DEVICE
2.4. Connecting monitor
The NVR-6204P4-H1-II and NVR-6208P8-H1-II recorders have HDMI and VGA connectors.
Following resolutions are supported: 1024x768, 1280x1024, 1920x1080.
NOTE:
Emergency switching of the screen resolution is possible after pressing the right mouse button
for more than 5 seconds until you hear a sound signal from the recorder.
2.5. Connecting cameras and network
NVRs have built-in 4 or 8 PoE ports RJ-45 with PoE support, which can be used for connecting
cameras. Please notice that the Ethernet connection is effective within 100 meter distance. In extended
mode, the length of the cable can reach up to 200m, but the bandwidth of the link is limited to 10Mbps.
Additionally, the recorders have a LAN port that allows to connect the recorder to a switch.
We recommend to configure the cameras before connecting to the recorder as described in the camera
user's manual. Please remember that cameras should be addressed with a unique IP address supported
by the recorder.
Connecting cameras and network devices to the recorder:
NETWORK SWITCH
IP CAMERAS
IP CAMERAS
INTERNET
PC

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
11
2.6. Connecting external devices
• Connecting USB devices
The NVR-6204P4-H1-II and NVR-6208P8-H1-II recorders have 2 USB 2.0 ports on the rear panel.
The ports allow to connect a USB memory, mouse and other compatible USB devices.
2.7. Security recommendations for network architecture and configuration
NOTE!
Below are shown security recommendations for network architecture and configuration
of CCTV systems that are connected to the Internet to reduce the risk
of unauthorized interference with the system by a third party.
1. Absolutely change the default passwords and user names (if the device gives this possibility)
of all applied network devices (recorders, cameras, routers, network switches,
etc.) to the severely complexity password. Use lowercase and uppercase letters, numbers, and special
characters if there is such possibility.
2. Depending on the available functionality in the order to restrict access to the used network devices
at the administrator account level, it is recommended to configure the users accounts accordingly.
3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open
the access to recorder system from the Internet on all ports, which gives possibility for
an unauthorized interference with the system.
Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance
of the connection (detailed information about ports of communication in different models of recorders,
cameras, etc. can be found in the operating instructions).
4. Use routers with firewall function and make sure it is enabled and properly configured.
5. It is recommended to change the default network communication port numbers of used devices
if there is such possibility.
6. If used network devices has aUPnP feature and it is not used, turn it off.
7. If used network devices has aP2P feature and it is not used, turn it off.
8. If used network devices support HTTPS protocol for connection, it is recommended to use it.
9. If used network devices support IP filtering for authorized connections function, it is recommended
to use it.
10. If used recorder has two network interfaces it is recommended to use both of them to physically
separate network for cameras and network for Internet connection. The only device in the system,
accessible from Internet is recorder - there is no physically access directly to any camera.
STARTING THE DEVICE

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
12
NVR OPERATING
3. NVR OPERATING
3.1. Front panel description
1. POWER Power supply signaling diode
2. IR PORT Infrared receiver for remote control
3.2. Controlling via USB mouse
It is possible to control all NVR functions using mouse with a USB interface. Double clicking on any
camera in split mode (e.g. 2x2, 3x3) switches it to full screen mode. Another double click returns to the
previous display mode.
A single click on a camera shows the channel menu. During configuration, the left mouse button select
individual items. Some indicated parameters can be changed by the mouse wheel. The right button
allows to leave the menu.
3.3. First launch
To start the unit connect the DC adapter and wait for initialization. It lasts for approximately 60
seconds. During this time executing any device functions and pressing any buttons is prohibited.
After first launch NVR displays window which allows to choose the language and location.
1
2

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
13
NVR OPERATING
In the next step, read and accept the Privacy Statement. Check the checkbox at the bottom of the
window and press OK.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
14
NVR OPERATING
The next wizard window allows to set time parameters such as TIME ZONE, SYSTEM TIME, DATE
FORMAT, TIME FORMAT, DST, SYNCHRONOUS, NTP SERVER and VIDEO FORMAT. After
making your selection, click the NEXT button.
Change the password in the password change wizard. The password must be at least 8 characters long.
It should contain a number, and upper and lower case letters. Enter them on the screen keyboard
available after clicking in the NEW PASSWORD and CONFIRM PASSWORD fields.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
15
NVR OPERATING
To display the entered password, check the DISPLAY PASSWORD box. Selecting LOG IN
AUTOMATICALLY checkbox will automatically log the user into the system after starting the
recorder.
By selecting the ENABLE field in the PATTERN LOCK row, it is possible to activate the setting of
enabling access for the user by means of a graphic pattern instead of entering the password. To start
the graphic symbol settings, click the EDIT button. Then, holding down the left mouse button, move
the cursor between the displayed circles twice to mark the pattern that will be used to unlock the
device.
After clicking on the NEXT button, a window is displayed that allows you to set a set of questions and
answers that can unlock access to the recorder.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
16
NVR OPERATING
To add a question, click on the QUESTION field to enter the question using the keyboard. Then click
on the ANSWER field to enter the answer to the question. Clicking on the ADD button adds a set of
questions and answers. Clicking the NEXT button takes you to the window in which information about
the disk connected to the recorder is displayed.
If the STATUS field displays information about the inaccessibility of the disk, format the disk by
clicking on the FORMAT button. A window appears asking to confirm that you want to format the
disk.
NOTE: Formatting causes the loss of information stored on the hard drive.
Pressing the OK button confirms the intention to format the disk.
The status of the disk should be "READ AND WRITE" after successful formatting.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
17
NVR OPERATING
3.4. Startup configuration
After the first start of the NVR, the setup wizard window is displayed (if the function has not been
disabled before). In order to properly configure the recorder, follow these steps with the procedure:
Note:
For suggested values for IP camera setting please refer to the “Cameras Capability Table”
available on the www.novuscctv.com website. If you set wrong values some problems may
appear: the NVR cannot search the IP camera, the stream cannot be connected, the image is not
fluent, the image quality is bad and so on.
Before starting work with the network recorder, you must perform the initial configuration of the
device. Click on the SETUP WIZARD button to run the wizard

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
18
NVR OPERATING
I. NETWORK SETTINGS:
The menu allows to change the recorder's network settings necessary for communication. By default,
the recorder has the IP address and DNS settings from the DHCP server enabled. If the address
retrieval fails, the recorder is available at 192.168.1.100 with the subnet mask of 255.255.255.0.
The displayed menu allows to change the settings after uncheck the OBTAIN AN IP ADDRESS
FROM AUTOMATICALLY checkbox and the OBTAIN DNS AUTOMATICALLY field. The
following network recorder settings are available, such as: IP (default 192.168.1.100) Subnet mask
(default setting is 255.255.255.0). If the NVR needs to be connected to the Internet (for remote access,
sending emails, etc.), the IP addresses for Gateway and for Primary and Secondary DNS. You can
change the default HTTP and HTTPS ports intended for displaying the device's web panel as well as
RTSP ports and server data port.
There is the addressing of the second network interface of the recorder for PoE ports on the right side.
The IP address and subnet mask are set for this interface. It is also possible to set the operating mode of
network ports - Non-long line mode guarantees standard transmission over a distance of up to 100m
with a bandwidth of 100Mb/s, Long line mode allows for transmission up to 200m with a bandwidth
limit of 10Mb/s.
NOTE!
The addresses of the LAN interface and the interface for PoE ports must belong to different
subnets.
Parameter changes must be confirmed with the NEXT button

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
19
NVR OPERATING
II. ADD CAMERA:
Next window allows to configure the IP camera and add them to the recorder. Upper window displays
cameras found by the NVR in local network. Before adding cameras to the system, make sure that
they have a unique IP address. Cameras with IP addresses that have already been added to the NVR
will not be displayed in the search part.
To change the addressable cameras, click on the icon in the column EDIT (This function works
only with NOVUS IP 6000 camera series).
Enter the address in the IP ADDRESS field and set the masks in the SUBNET MASK, then press the
OK button to save the settings.
Press the button to add the camera to the system
In the lower window there is a list of available channels. It is possible to change the name of the
channel after clicking in the EDIT field.
NOTE:
The process of adding NOVUS IP 6000 series cameras with software 5.1.x and higher in which
the activation process has not been carried out cannot be correctly carried out in the start-up
wizard (v1.4.8 NVR firmware). You can check the camera firmware version in the VERSION
column.

NVR-6204P4-H1-II, NVR-6208P8-H1-II Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.
20
NVR OPERATING
Added camera is displayed on the bottom of the menu list. To edit the connection settings of the
camera, press the button in EDIT column.
If you are having problems connecting to the camera, you must enter the correct user name in the
USER NAME and password in the PASSWORD field and then press the OK button to save the
settings.
NOTE:
It should be borne in mind that if the camera password is changed from the level of e.g. a web
browser, the newly defined password must also be entered in the recorder. Otherwise, after a
longer time from changing the password or after restarting the camera or recorder, the
communication between the camera and the recorder will be lost. This is especially important for
cameras with firmware version 5.1.0.0 and newer. These cameras do not have a defined default
password (it means that the cameras are not activated by default), a new strong password should
be defined when connecting to the camera for the first time. Without defining a new strong
password, the camera configuration from the web browser will not be possible.
If the NVR connected to the camera, STATUS filed will display “Connected”.
To remove a camera from the list, press the in DELETE column.
III. RECORD SETTINGS:
You can set one of the modes:
- MANUAL RECORD SETTINGS - You can set the recording time from the moment you select the
manual recording in range from 1 minute to 1 hour or manually off recording.
AUTO - set all the cameras on one of the following modes :
- MOTION RECORD - starts recording after receiving motion detection information from the camera.
- SENSOR RECORD - starts recording after alarm generated on alarm input