NSFOCUS ADS NX3 2000 Series User manual

Version: V4.5R89F00 (2016-03-05)
NSFOCUSADS
Installation Guide
© 2016 NSFOCUS

■ Copyright © 2016 NSFOCUS Technologies, Inc. All rights reserved.
Unless otherwise stated, NSFOCUS Technologies, Inc. holds the copyright for the content of this document,
including but not limited to the layout, figures, photos, methods, and procedures, which are protected under the
intellectual property and copyright laws. No part of this publication may be reproduced or quoted, in any form
or by any means, without prior written permission of NSFOCUS Technologies, Inc.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
i
V4.5R89F00 (2016-03-05)
Contents
Preface ................................................................................................................................................1
Scope......................................................................................................................................................................1
Audience ................................................................................................................................................................1
Organization...........................................................................................................................................................2
Conventions ...........................................................................................................................................................2
Customer Support...................................................................................................................................................2
1 Overview.........................................................................................................................................4
1.1 Appearance.......................................................................................................................................................4
1.1.1 ADS NX3-2000 Series and NX5-4000/6000 Series................................................................................4
1.1.2 ADS NX5-8000 Series............................................................................................................................6
1.1.3 ADS NX3-200E/600E.............................................................................................................................7
1.2 Power Supply...................................................................................................................................................8
1.3 LEDs ................................................................................................................................................................9
1.4 System Information........................................................................................................................................ 11
2 Preparations..................................................................................................................................14
3 Installation Procedure ................................................................................................................16
3.1 Installation Flowchart.....................................................................................................................................16
3.2 Connecting Power Cable................................................................................................................................17
3.2.1 AC Power Supply..................................................................................................................................17
3.2.2 DC Power Supply .................................................................................................................................17
3.3 Network Connection ......................................................................................................................................18
3.4 Device Shutdown ...........................................................................................................................................18
3.5 System Deployment .......................................................................................................................................18
3.5.1 In-Path Deployment..............................................................................................................................18
3.5.2 Out-of-Path Deployment.......................................................................................................................19
4 Initial Configuration ..................................................................................................................20
4.1 Login to Console............................................................................................................................................20
4.2 Network Configuration on the Console..........................................................................................................23
4.3 Login to Web-Based Manager........................................................................................................................24
4.4 Network Configuration on Web-based Manager............................................................................................26
5 System Maintenance...................................................................................................................27
5.1 System Upgrade .............................................................................................................................................27

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
ii
V4.5R89F00 (2016-03-05)
5.2 Common Troubleshooting..............................................................................................................................28
5.2.1 Web Login Failure.................................................................................................................................28
5.2.2 Device Access Failure...........................................................................................................................28
5.2.3 Verification Image Display Failure .......................................................................................................28
5.2.4 License Import Failure..........................................................................................................................29
5.2.5 MAC Address Learning Failure............................................................................................................29
5.2.6 Ping Failure or Excessive Packets Drop ...............................................................................................30
A Default Parameters ....................................................................................................................31
A.1 Default Management Interface Settings ........................................................................................................31
A.2 Default Web Administrator Account .............................................................................................................31
A.3 Default Console Administrator Account........................................................................................................31
A.4 Default CLI Administrator Account ..............................................................................................................31
A.5 Console Specification....................................................................................................................................31

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
iii
V4.5R89F00 (2016-03-05)
Figures
Figure 1-1 Appearance of ADS NX5-4020............................................................................................................5
Figure 1-2 Front panel of ADS NX5-4020.............................................................................................................5
Figure 1-3 Rear panel of ADS NX5-4020..............................................................................................................6
Figure 1-4 Front panel of ADS NX5-8000.............................................................................................................6
Figure 1-5 Rear panel of ADS NX5-8000..............................................................................................................7
Figure 1-6 Front panel of ADS NX3-200E/600E...................................................................................................7
Figure 1-7 Rear panel of ADS NX3-200E/600E....................................................................................................8
Figure 3-1 Installation flowchart..........................................................................................................................16
Figure 3-2 In-path deployment of an ADS device................................................................................................19
Figure 3-3 Out-of-path deployment of an ADS device ........................................................................................19
Figure 4-1 Location Information dialog box........................................................................................................21
Figure 4-2 Connection Description dialog box ....................................................................................................22
Figure 4-3 Port connected to HyperTerminal.......................................................................................................22
Figure 4-4 Configuring port attributes .................................................................................................................23
Figure 4-5 Prompt ................................................................................................................................................23
Figure 4-6 Security alert page ..............................................................................................................................24
Figure 4-7 Login page..........................................................................................................................................25
Figure 4-8 Web-based manager............................................................................................................................25
Figure 5-1 System upgrade ..................................................................................................................................27

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
iv
V4.5R89F00 (2016-03-05)
Tables
Table 1-1 AC power LEDs.....................................................................................................................................8
Table 1-2 DC power LEDs.....................................................................................................................................9
Table 1-3 Power LED...........................................................................................................................................10
Table 1-4 Status LED...........................................................................................................................................10
Table 1-5 System LED.........................................................................................................................................10
Table 1-6 Interface LED.......................................................................................................................................10
Table 1-7 Hardware specifications of ADS NX5-6025/NX5-4020/NX3-2020/NX3-2010.................................. 11
Table 1-8 Hardware specifications of ADS NX5-8000........................................................................................12
Table 1-9 Hardware specifications of ADS NX3-200E/600E..............................................................................13

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
1
V4.5R89F00 (2016-03-05)
Preface
Scope
This document describes the basic information and detailed installation procedure about
NSFOCUSADS NX3 2000 series (ADS NX3-2020 andADS NX3-2010), NX3-200E,
NX3-600E, NX5 4000 series (ADS NX5-4020), NX5 6000 series (ADS NX5-6025), and
ADS NX5 8000 series (ADS NX5-8000).
This document provides guidance for you in use of the products. Descriptions in this guide
may slightly differ from actual products due to version upgrade or other reasons.
Unless otherwise indicated, figures and texts in this manual use ADS NX5-4020 as an
example.
Currently, two types of model naming methods exist for ADS products, as shown in the
following table.
Old Model
Corresponding New Model
Comparison
ADS 2010
ADS NX3-2010
The functions remain the same. The manuals of one
can be used for the other.
ADS 2020
ADS NX3-2020
The functions remain the same. The manuals of one
can be used for the other.
ADS 4020
ADS NX5-4020
The functions remain the same. The manuals of one
can be used for the other.
ADS 6025
ADS NX5-6025
The functions remain the same. The manuals of one
can be used for the other.
Audience
This document is intended for the following users:
System administrator
Network administrator
Users who wish to know main techniques and installation procedure of this product
This document assumes that you have a basic knowledge in the following areas:

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
2
V4.5R89F00 (2016-03-05)
Network security
Linux and Windows operating systems
TCP/IP protocols
Organization
Chapter
Description
1 Overview
Describes hardware configuration and system architecture of ADS devices.
2 Preparations
Describes preparations before installing ADS devices.
3 Installation Procedure
Describes methods for installing ADS devices.
4 Initial Configuration
Describes methods for configuring the network after installation.
5 System Maintenance
Describes methods for maintaining ADS devices and common
troubleshooting.
A Default Parameters
Describes default parameters about ADS devices.
Conventions
Convention
Description
Bold font
Keywords, names of screen elements like buttons, drop-down lists or fields, and
user-entered text appear in bold font.
Italic font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
Reminds users to take note.
Indicates a tip to make your operations easier.
Indicates a situation in which you might perform an action that could result in
equipment damage or loss of data.
Indicates a situation in which you might perform an action that could result in
bodily injury.
A > B
Indicates selection of menu options.
Customer Support
To obtain materials about network security, visit NSFOCUS website at:
http://www.nsfocus.com/en/index.html

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
3
V4.5R89F00 (2016-03-05)
To obtain professional service information and business information about NSFOCUS
network security, contact us at:
Global Support
24/7 service hotline:
[phone]
[phone]
Email: [e-mail]
NSFOCUS US
Tel: [phone]
Email: [email protected]m
NSFOCUS Japan
Tel: [phone]
Email: [email protected]
NSFOCUS Malaysia
Tel: [phone]
Fax: [phone]
NSFOCUS APAC
Email: [email protected]om
NSFOCUS Australia & New Zealand
Email: mailto:[email protected]
NSFOCUS EU
Email: mailto:[email protected]
NSFOCUS MENA
Email: [e-mail]

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
4
V4.5R89F00 (2016-03-05)
1 Overview
The ADS system is an integrated hardware device. This chapter gives a brief account of them.
1.1 Appearance
This section details the appearance, including front and rear panels, ofADS devices.
The interface model or quantity of real products may slightly vary with the batch or
model.
1.1.1 ADS NX3-2000 Series and NX5-4000/6000 Series
ADS NX3-2000 series, NX5-4000 series, and NX5-6000 series use the same hardware
platform, and therefore have the same appearance and hardware specifications. This guide
uses ADS NX5-4020 as an example to describe their appearance.
Figure 1-1 shows the appearance ofADS NX5-4020.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
5
V4.5R89F00 (2016-03-05)
Figure 1-1 Appearance ofADS NX5-4020
Front Panel
Figure 1-2 Front panel ofADS NX5-4020
①Management interface
②Hot standby port
③RJ45 console port
④USB interface
⑤Reset button
⑥Power LED
⑦Status LED
⑧System LED
⑨Working interfaces

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
6
V4.5R89F00 (2016-03-05)
Rear Panel
Figure 1-3 Rear panel ofADS NX5-4020
①Power switch
②Power supply 1
③Power supply 2
1.1.2 ADS NX5-8000 Series
Figure 1-4 and Figure 1-5 show the front and rear panels of ADS NX5-8000, respectively.
Figure 1-4 Front panel ofADS NX5-8000
①Power switch
②Reset button
③Power LED: PWR
④Status LED: STA
⑤System LED: SYS
⑥IPMI
⑦Management interface: M
⑧Management interface: H1
⑨Console port (RJ45): S
⑩USB port
⑪Working interface: 10G
interface
⑫Working interface: 10G
interface
⑬Expansion interface
⑭Expansion interface

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
7
V4.5R89F00 (2016-03-05)
Figure 1-5 Rear panel ofADS NX5-8000
①Power supply 1
②Power supply 2
③Switch of power supply 2
④Switch of power supply 1
⑤Ventilation holes
⑥Ground connector
1.1.3 ADS NX3-200E/600E
Figure 1-6 and Figure 1-7 show the front and rear panels of ADS NX3-200E/600E,
respectively.
Figure 1-6 Front panel of ADS NX3-200E/600E
①Reset button
②Status LED
③Power LED
④System LED
⑤RS-232 serial port (RJ45)
⑥Management port (crossover
cable)
⑦USB port
⑧Scan ports: GE electrical ports for scanning (RJ-45,
100/1000M adaptive, straight-through network cable)

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
8
V4.5R89F00 (2016-03-05)
Figure 1-7 Rear panel of ADS NX3-200E/600E
①Ground connector
②Power switch
③Power port
1.2 Power Supply
The ADS devices support both AC and DC inputs. Before delivery, the ADS devices are
configured with power modules. You can determine to use the AC or DC power module based
on the equipment room environment. If necessary, connect theADS device to two
independent power supplies to implement 1+1 power redundancy. In this case, even if one of
the power modules fails, ADS devices still operate properly. The power switch and socket
reside at the rear of the chassis, as shown in Figure 1-5.
Specifications of the AC Power Supply
Rated voltage range: 100–240 V AC; 50–60 Hz
Max output power: 450 W
Table 1-1 describes functions of AC power LEDs.
Table 1-1 AC power LEDs
LED
Description
AC On (yellow)
After the power supply is connected, the AC LED is on, indicating that the
power input is normal.
AC Off
After the power supply is connected, the AC LED is off, indicating that the
power is off, overloaded, or fails.
OK On (yellow)
After the device is started, the OK LED is on, indicating that the power output
is normal.
OK Off
After the device is started, the OK LED is off, indicating that the power is
overloaded or fails.
The OK indicator is available for the AC power supply on the following devices, but
unavailable for the AC power supply on ADS NX3-200E, NX3-600E, and NX5-8000:
ADS NX3-2020/2010
ADS NX5-4020
ADS NX5-6025
ADS NX3-200E and NX3-600E support single AC power only, with the
following withstand voltage requirements:

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
9
V4.5R89F00 (2016-03-05)
AC 1500V 1 minute (FG-LG, SG-LG)
AC 500V 1 minute (FG-SG)
Specifications of the DC Power Supply
ForADS NX3-2020/2010, ADS NX5-4020, and ADS NX5-6025, the DC power supply
specifications are as follows:
Voltage range: –40 to 60 V DC
Maximum output power: 450 W
ForADS NX5-8000, the DC power supply specifications are as follows:
Voltage range: –36 to –72 V DC
Maximum output power: 500 W
Table 1-2 describes functions of the DC power LEDs.
Table 1-2 DC power LEDs
LED
Description
DC On (yellow)
After the power supply is connected, the DC LED is on, indicating that the
power input is normal.
DC Off
After the power supply is connected, the DC LED is off, indicating that the
power is off, overloaded, or fails.
OK On (yellow)
After the device is started, the OK LED is on, indicating that the power
output is normal.
OK Off
After the device is started, the OK LED is off, indicating that the power is
overloaded or fails.
The OK indicator is available for the DC power supply on the following devices, but
unavailable for the DC power supply on ADS NX5-8000:
ADS NX3-2020/2010
ADS NX5-4020
ADS NX5-6025
1.3 LEDs
There are four types of LEDs on the front panel of the chassis: power LED, status LED,
system LED, and interface LED.
Power LED
Table 1-3 describes functions of the power LED.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
10
V4.5R89F00 (2016-03-05)
Table 1-3 Power LED
LED
Description
On
Indicates the power is normal.
Off
Indicates the power is off or abnormal.
Status LED
Table 1-4 describes functions of the status LED.
Table 1-4 Status LED
LED
Description
Green
Indicates that the system is in normal state.
Red
Indicates that the engine is in abnormal state.
System LED
Table 1-5 describes functions of the system LED.
Table 1-5 System LED
LED
Description
Green
Indicates that the memory usage is normal.
Red
Indicates that the memory usage of the device exceeds 90%.
Link/Act LED
Table 1-6 describes the Link/Act LED on the chassis.
Table 1-6 Interface LED
LED
Description
Link On
Indicates a link has been established.
Link Off
Indicates the link is not established.
Act On
Indicates the ADS device is transmitting or receiving data.
Act Off
Indicates no data is transmitted or received.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
11
V4.5R89F00 (2016-03-05)
1.4 System Information
Table 1-7 lists hardware specifications of ADS NX5-6025/NX5-4020/NX3-2020/NX3-2010.
Table 1-7 Hardware specifications ofADS NX5-6025/NX5-4020/NX3-2020/NX3-2010
Interface
1 x RJ-45 console port
1 x RJ-45 Gigabit Ethernet electrical port (management interface)
1 x Hot standby port of the management interface
1–2 x 10 Gigabit Ethernet SFP interface (reserved for the 10 Gigabit card
that you can purchase from NSFOCUS)
1–8 x Gigabit Ethernet optical port (selected by users as required)
1–8 x Gigabit Ethernet electrical port (selected by users as required)
Weight
12 kg
Height
88 mm (2U)
Depth
440 mm
Width
564 mm
Rack
19-inch rack
Power Supply
AC/DC dual power supplies, 1+1 redundancy, hot swap
DC input: –40 V to –60 V DC
AC input: 100–240 V AC
Maximum power: 450 W
MTTF
60,000 hours
Operating
Temperature
0–45°C
Storage
Temperature
–20°C to +70°C
Table 1-8 lists hardware specifications of ADS NX5-8000.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
12
V4.5R89F00 (2016-03-05)
Table 1-8 Hardware specifications ofADS NX5-8000
Interface
2 x management interface (M and H1)
1 x RJ-45 console port
2 x USB port
4 x 10 Gigabit Ethernet SFP interface (for the 10 Gigabit card)
1–8 x 1000M Ethernet optical port (optional)
1–8 x 1000M Ethernet electrical port (optional)
Weight
16.5 kg (without packing weight)
Height
88.5 mm (2U)
Depth
626 mm
Width
443 mm
Rack
19-inch rack
Power Supply
AC redundancy power supply: 10–240 V AC
Maximum AC power: 450 W
DC redundancy power supply: –36 V to –72 V DC
Maximum DC power: 500 W
MTTF
45,000 hours
Operating
Temperature
5–40°C
Storage
Temperature
–20°C to +80°C
Table 1-9 lists hardware specifications of ADS NX3-200E/600E.

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
13
V4.5R89F00 (2016-03-05)
Table 1-9 Hardware specifications ofADS NX3-200E/600E
Interface
1 x RJ-45 console port
1 x RJ-45 1GbE electrical management port
6 x 1GbE electrical port
Weight
7 kg
Height
44 mm (2U)
Depth
390 mm
Width
430 mm
Rack
19-inch rack
Power Supply
Single AC power. Hot swap is not allowed.
MTTF
45,000 hours
Operating
Temperature
0–40°C
Storage
Temperature
–40°C to +70°C

NSFOCUS ADS Installation Guide
Copyright © NSFOCUS
14
V4.5R89F00 (2016-03-05)
2 Preparations
Prepare the following before installing ADS devices:
Accessories supplied with the device
Before installation, verify the following items are included in the accessory box
delivered with the device:
−Straight-through cable: Used for network connections.
−Crossover cable: Used to connect a computer to the management interface ofADS
devices so that you can log in to the web-based manager to perform configurations.
−Power cable: One or two power cables for each device.
−Rubber pad: Cut into four pieces along the dotted line and attached to four angles or
tags of the device chassis to avoid abrasion.
−Rack-mounting ear: Used to fasten the device to the rack.
−Rack-mounting screw: Used to fasten the device to the rack.
−Console port cable: Used for the configuration of the device console.
Accessories supplied may vary with product model. Please refer to the packing list.
Besides the stuff in the accessory box, prepare the following:
−IP address: IP address reserved for ADS devices. You are advised to reserve both an
IPv4 address and an IPv6 address for an ADS device.
−Computer: Directly connected to the management interface of theADS device so that
you can log in to the web-based manager of the device in HTTPS mode for
management.
−Terminal software: Connected to the console port, for example, HyperTerminal
pre-configured in the Windows operating system.
−Browser: Verify that a web browser is available on the computer. IE 8.0 through 10.0
and Chrome are recommended.
User-provided tools and devices
−Phillips screwdriver: P1-100 mm, P2-150 mm, P3-250 mm
−Flathead screwdriver: P4-75 mm