Nuga NM-200 User manual

www.nuga.kr
NM-200
User Manual
ENGLISH / CE H/H / B TYPE / Rev. 00
2016.11.03
Tourmanium Product
Quality Warranty Enclosed
[ ENGLISH ]
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
TEL : [phone] / FAX : [phone]
http://www.nuga.kr
Thank you for purchasing this product.
Before use...
Please read the cautions for safety in the
user manual to use this product safely.


NM-200
Product Components
Names and Functions of Product
Descriptions for Controller Buttons
How to Use Product
How to Take Emergency Actions during Use
How to Store and Clean after Use
Self-check Items
Before any A/S request
Controller Check Indicator Window
Product Specifications
Product Warranty
8
9
10
14
17
20
21
22
23
24
25
Product Introduction
How to Use Product
Product Storage and Care
Contents Cautions for Safety
Cautions for Safety
Cautions for your safety
Disclaimer
· These cautions include descriptions for the safety of users and prevention
of any damage to properties among others.
· Read through the following details to use the product appropriately.
· This Manual classifies the risk level into following three degrees and the
following graphical symbols remind users of cautions for matters and
operations of concerns about any risk.
· The manufacturer, importer and/or agent shall not be responsible for any
problem and/or other damage to the product which has been caused
from the user’s fault or operation.
· Information in the user manual has been prepared on the basis of the current
product specifications.
· Details in the user manual might be different from those on the product.
· The product manufacturer will be adding and supplementing new functions
at any time and new technologies shall be applied to the product continuously
in the future as well.
· All the standards and functions are subject to change without any notice
to users to improve performance.
Interpretations on symbols
Caution
If there is a possibility of a minor injury or damage to goods due to
non-compliance.
Danger
If there is high possibility of death due to non-compliance.
Warning
If there is a possibility of an injury or death due to non-compliance.


NM-200
Cautions for Safety
Put the projector sock on the projector while
using the projector to keep the projector from
touching the skin directly.
(Otherwise, it is likely that injuries occur.)
Avoid pulling out the power cord parts or touching
the power plug with the wet hands.
(Otherwise, it might cause electrical shock or fire.)
Do not use it for other usages than the described
purposes of uses.
(Otherwise, it might cause damage to the product.)
Do not apply washing or dry-cleaning.
(Otherwise, it might cause damage to the product
or any danger of electric shocks or fire.)
Anyone other than technicians qualified for our
company’s A/S should not disassemble, repair
or modify the product for any reason.
(Otherwise, it might cause damage to the product
or electric shock and/or fire.)
The appliance is not to be used by people
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been under
supervision or instruction
Do not place any heavy object or other electric
heater on this product.
(Otherwise, it might cause injuries or damage to
the product.)
Do not place any inflammable substances such as
the candle light, cigarette light and/or wine among
others, any vessel containing water, heavy object
and other substances.
(Otherwise, it might cause fire.)
Do not place the controller covered with any quilt
during use.
(Otherwise, it might cause damage to the product
or a danger of fire.)
Danger Warning
Avoid bending the power cord excessively or
pressing it down with heavy objects.
Never use other temperature controllers with
different specifications.
(Otherwise, it might cause damage to the product.)
Anyone using a cardiac pacemaker should consult
with a doctor before any use of this product.

NM-200
Product Components
Names and Functions of Product
Descriptions for Controller Buttons
8
9
10
Product Introduction
NM-200
Remove the power cord from the socket during no
use for a long time.
Keep any pin, wire or other metallic pieces from
stabbing or inserting to the product.
(Otherwise, it might cause damage to the
product.)
Use the product in a proper range of temperature
(50~60୅).
(Otherwise, it might cause burns.)
Do not expose the product to the direct sunlight.
(Otherwise, it might cause damage to the product.)
Check out the voltage before any use to ensure
the applicable voltage and apply the power plug to
the dedicated socket in any way.
Please abide by defined time and methods.
Caution
]WGGGGGGGGGGGGGGGG]W\WGGGGGGGGGGGGGGGG\W[WGGGGGGGGGGGGGGGG[WZWGGGGGGGGGGGGGGGGZW

Heater Controller
User ManualPocket Heater Cover
It is connected to an outlet to input the power supply
to the product.
ⴚPower cord
It controls temperature in the heater with convenience
in use due to the compact design.
ⴙController
Name Function
The heater as the main component in the product is
combined with tourmanium to increase the heating
effects.
ⴘHeater
Product Introduction
ⴘHeater ⴙController ⴚPower cord
Names and Functions of Product Product Components
NM-200
www.nuga.kr
NM-2 0 0
User Manual
Thank you for purchasing this product.
Before use...
Please read the cautions for safety in the
user manual to use this product safely.
Tourmanium Product
QualityWarranty Enclosed
[ENGLISH ]
i
Introduction
Please check out whether all the components are unpacked in hand
before installing the product.
Please inquire from of your supplier if there is any missing or
damaged component.
Some specifications and/or designs are subject to change for
improving the product performance.

Descriptions for Controller Buttons

Unit to display operation state of the heater
Unit to display the setting/current temperature
of the heater
Unit to display turn on/off of the controller
Unit to control ON/Off of the power supply
for the controller
Unit to control the temperature of the heater
Cable for supplying power to the controller
Name Function
NM-200
Product Introduction
ྛOperation
indicator lamp
ྚTemperature
indicator window
ྙPower indicator lamp
ྜPower button
ྜྷTemperature
control dial
ྞPower input cable

Memo

NM-200
How to Use Product
How to Take Emergency Actions during Use
14
17
How to Use Product
NM-200

How to Use Product
TUFQTUFQTUFQ
Press the power button on the
controller to turn on the power
supply for the product and
controller after connecting the
power cord to a socket.
The current temperature is
shown on the temperature
indicator window.
The current temperature is
shown on the temperature
indicator window after the
user’s setting temperature
is blinking three times.
A red light is lit on the
operation indicator lamp if
the current temperature is
higher than the setting
temperature.
Turn the temperature control dial
clockwise on the controller to set
the desired temperature.
(30~70୅)
Power
indicator lamp
How to Use Product
Before using product
'RQRWXVHLWIRURWKHUXVDJHVWKDQWKHGHVFULEHGSXUSRVHVRIXVHV&KHFNRXWWKHYROWDJHLQXVHEHIRUHDQ\XVH$Q\RQHXVLQJDFDUGLDFSDFHPDNHUVKRXOGFRQVXOWZLWKDGRFWRUbefore any use of this product.
1HYHUXVHRWKHUWHPSHUDWXUHFRQWUROOHUVZLWKGLIIHUHQWspecifications.
'RQRWSODFHWKHFRQWUROOHUFRYHUHGZLWKDQ\TXLOWGXULQJXVH8VHWKHSURGXFWLQDSURSHUUDQJHRIWHPSHUDWXUHKeep the product tightly close
to the desired area in the body
after setting the temperature.
i
NM-200

How to Take Emergency
Actions during Use
TUFQTUFQ
Remove the power cord from
the socket in any case after
using the product.
Then, all the lamps on the
controller are tuned off.
Press the power button to turn
off the power on the product
and controller if you want to
stop using the product.
NM-200
How to Use Product
Stop using the product immediately and remove
the power plug if there is any lightning.
Stop using the product immediately and contact
your supplier branch or our company if you smell
any burn or detect any smoke from the product.
Stop using the product immediately and consult
with a doctor if any abnormality occurs to the
human body.
Turn off the power switch immediately, stop using
the product and contact our company if you find
out any failure or power failure from the product.
Turn off the power switch, remove the power
plug immediately, and then contact our company
if you have poured water into the product.

Memo

NM-200
How to Store and Clean after Use
Self-check Items
Before any A/S request
Controller Check Indicator Window
Product Specifications
Product Warranty
20
21
22
23
24
25
Product Storage and Care
NM-200

Check before use
Product Storage and Care
How to Store and Clean after Use Self-check Items
1. Is the power cord connected to an outlet?
2. Are lights on the power lamp and indication
window turned on when the power supply is
applied?
3. Is the temperature indication displayed on the
temperature indicator window on the controller?
4. Is the temperature increasing well in the
product?
5. Is the temperature in the product not too high?
6. Did you check out conditions for any damage
to the power cord or cable conditions?
Yes No
Yes No
Yes No
Yes No
Yes No
Yes No
Check after use
· During operations: temperature (0~35୅), humidity (20~80%)
· Transport and storage conditions: temperature (-25~70୅),
humidity (20~80%), atmospheric pressure (700hPa to 1060hPa)
Caution
Remove the power plug before cleaning
There might be a danger of electric shocks.
Environmental conditions
How to clean
Controller
Wipe it out with a piece
of dry cloth if there is
any foreign substance.
Product top
Wipe it out with wax
for leather or dry cloth.
Caution
There might be a danger of injuries or fire if you fail to check out the
following. Please make sure that your check them out.
NM-200
Yes No
Yes No
Yes No
Yes No
1. Is the temperature on the temperature indicator
window on the controller turned off?
2. Are lights on the power lamp and indicator
window turned off?
3. Is the power cord removed from the outlet?
4. Is the place to keep the product exposed to
the humidity dust and/or chemicals?
Introduction
1. Separate the power cord while the product is not in use for a long time.
2. Be aware of the following for the storage place.
ྙKeep the product in a place with no water.
ྚKeep the product in a place with no concern of any adverse effect such
as the air pressure, temperature, humidity, ventilation, sunlight and/or
air containing dust, salt, sulfur, etc.
ྛBe careful of safety conditions such as the slope, vibration, shock, etc.
(including those during transportation).
ྜDo not keep the product in a place near any chemical or gas.
ྜྷAvoid any direct sunlight during the storage.
3. Store the product after cleaning the components.
i

Before any A/S request
Controller Check Indicator Window
Check items for any abnormality in the power supply
If the temperature is
not indicated on the
temperature
indicator window;
Check items for any abnormality in the heating
If the temperature is
not increasing in the
product; ྙCheck out if the power button in the
controller is pressed to turn on the
product.
ྚCheck out if the temperature is set to
too weak a condition.
ྛDo not disassemble the product but
contact your supplier or our company.
Display Descriptions Display location
Disconnection of
temperature sensor
The temperature
sensor is not
detected
Short circuit of
temperature sensor
The temperature
sensor is under
the short circuit
Disconnection
of heating unit
The heating unit is
disconnected or
under the disconnection
by the bimetal operation
Overheating of
heating unit
The temperature in the
heating unit is
increased more
than 86Ȕ
Product Storage and Care
NM-200
Caution
Ensure checking out the following before applying for A/S if any
abnormality occurs in the product.
The product might fail to operate normally even without any failure
if you use it without reading the manual.
Caution
Do not disassemble the product arbitrarily if any error occurs, but
remove the power plug, turn off the power switch, and then contact
your supplier.
If you disassemble the product arbitrarily, it might cause serious
injuries and/or damage to the product.
ྙCheck out if the power plug on the controller
is connected to an outlet.
ྚCheck out if the power button in the
controller is pressed to turn on the product.
ྛCheck the operating voltage.

Product Specifications
NM-200
Thermal massager
NM-200
NUGA MEDICAL CO., LTD.
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
Marked on the product
1.5 kg
207 X 76 X 60.9 (mm)
Refer to the user manual
Refer to the user manual
AC 220-240V~, 50-60 Hz
25 W
Product name and
model name
Manufacturer
Date of manufacture /
number of manufacture
Product weight
Product size
Cautions during use
Operating method
Electric rating
Power consumption

Memo Memo
Memo
NM-200