Nuga NM-5000 User manual

www.nuga.kr
NM-5000
User Manual
Tourmanium Product
Quality Warranty Enclosed
[ ENGLISH ]
ENGLISH / CE H/H / Rev. 08
2015.11.10
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
TEL : [phone] / FAX : [phone]
http://www.nuga.kr
Thank you for purchasing this product.
Before use...
Please read the cautions for safety in the
user manual to use this product safely.

Product features
Guide and Sequence for Product Installation
Product Components
Product Frame Components
Tray with Screws for Assembly
Names and Functions of Product Components
Descriptions for Remote Controller Buttons
Contents Cautions for Safety
Product Introduction
Before the Product Installation
How toAssemble the Product Frame
How to Install the Product
Test Operations after Installation
Product Installation and Preparations
How to Store and Clean the Product after Use
Check Indicator Window of Remote Controller
How to Take EmergencyActions during Use
Self-check Items
Before anyA/S Request
Product Specifications
Memo
Product Warranty
Product Storage and Care
How to Use the Remote Controller
How to Use the Product by Mode
How to Use the External Projector
How to Use the Low Frequency Pad
How to Use the Product
How to Set Temperature for the Sub Heater
8
9
10
11
12
14
16
18
20
24
26
40
41
42
43
44
45
46
47
28
28
33
34
36
38
How to Use the Product
Cautions for your safety
· These cautions include descriptions for the safety of users and prevention
of any damage to properties among others.
· Read through the following details to use the product appropriately.
· This Manual classified the risk level into the following three degrees and the
following graphical symbols aim to remind users of cautions for matters and
operations of concerns about any risk.
Disclaimer
· The manufacturer, importer and/or agent shall not be responsible for any
problem and/or other damage to the product which has been caused from the
user’s careless care or operation.
· Information in the user manual has been prepared on the basis of the current
product specifications.
· Details on the user manual might be different from those on the product.
· The product manufacturer is adding and supplementing new functions at any
time and new technologies shall be applied to the product continuously in the
future as well.
· All the standards and functions are subject to change without any notice to
users to improve performance.
Interpretations on symbols
Caution
If there is a possibility of a minor injury or damage to goods due to
non-compliance.
Warning
If there is a possibility of an injury or death due to non-compliance.
Danger
If there is high possibility of death due to non-compliance.

NM-5000
Cautions for Safety

Danger Warning
Put the projector cover on the
projector while using the
projector to keep the projector
from touching the skin directly.
(Otherwise, it is likely that injuries
occur.)
Ensure applying the product
only abdominal area manually,
while keeping the product from
applying to the area around ribs
if you have to apply the product
to the abdominal area.
Avoid applying the projector directly
to eyeballs to prevent from any risk.
(Otherwise, it might cause damage
to eyeballs.)
Avoid placing inflammable
substances like candlelight,
cigarette light or liquors and/or
vessels containing water, heavy
objects or other objects on the
product.
(Otherwise, it might cause fire.)
Do not insert many power
plugs for other products into
a socket to be used
simultaneously.
(Otherwise, it might cause
electric shock, injury and/or
damage to the product.)
Avoid twisting the body while
the internal projector is being
operated.
(Otherwise, it might cause
excessive influences to the
spine.)
Avoid using any band or belt
that does not come as one of
components from the purchase
of the product.
(Otherwise, it might cause
damage to the product.)
Avoid jumping on the product
or any other action to provide
shocks to the product.
(Otherwise, it might cause
injuries and/or damage to the
product.)
Use the product after checking
out any damaged or worn-out
cord.
(Otherwise, it might cause
electric shock, injury and/or
damage to the product.)
Avoid bending the power cord
excessively or pressing it down
with heavy objects.
Do not allow any child to use the
product alone.
Avoid pulling out the power cord
parts or touching the power plug
with the wet hand.
(Otherwise, it might cause the
electrical shock or fire.)
Immediately stop using the
product and turn off the power
if there is any thunder, lightning
or earthquake.
(Otherwise, it might cause the
electrical shock or fire.)
Avoid using the product in a
closed place with any fuel
and/or chemical.
(Otherwise, it might cause
injuries or fire.)
Avoid using the product in a
place with a great deal of dusts
or intensive temperature change.
(Otherwise, it might cause the
electrical shock or fire.)
Anyone other than technicians
qualified for our company’sA/S
shall not disassemble, repair or
modify the product by any means.
(Otherwise, it might cause damage
to the product or electric shock
and/or fire.)

NM-5000
Cautions for Safety
Prohibit any pregnant woman
near the parturition, patients with
rachischisis, patients wearing a
cardiac pacemaker and/or
patients with severe heart
diseases from using the product.
Apply the product to the area
with any surgery and/or
treatment, after consulting with
the store or the company from
which you have purchased the
product.

NM-5000
]WGGGGGGGGGGGGGGGG]W
\WGGGGGGGGGGGGGGGG\W
[WGGGGGGGGGGGGGGGG[W
ZWGGGGGGGGGGGGGGGGZW
Product features
Guide and Sequence for Product Installation
Product Components
Product Frame Components
Tray with Screws for Assembly
Names and Functions of Product Components
Descriptions for Remote Controller Buttons
8
9
10
11
12
14
16
Product Introduction
Caution
Use the product in a range of
proper temperature as there are
concerns of burns if the higher
temperature is set.
Any pregnant shall not use the
low frequency pad. Move the product after separating the power supply
from connecting lines if the
product is moved.
Connect the power supply after
connecting the remote controller
first.
Be aware of dangers that you
might fall down when you get on
or off the product.
Please abide by using time
and methods. Separate the power cord while the product is not being in use
for a long time.

NM-5000
Install the product horizontally.
Check out the applied voltage
before any use and apply the
power plug only to a dedicated
socket.

14
52
3
Guide and Sequence
for Product InstallationProduct features
Fine Design
ⴘThe design in a streamline shape makes you feel comfortable during use.
ⴙBeautiful materials with good feelings of touch in high quality are applied.
ⴚThe product in blue helps you improve concentration and psychological
stability.
Functional Product Frame
Both the main mat and sub mat are horizontally built, which can be used more
conveniently with the attachment of a handle to be controlled in 3 steps
UHVSHFWLYHO\IRUWKHGHVLUHGDQJOHRIÛÛRUÛ
Internal Projector Designed in Human Engineering
Ceramics are separately built in around the cervical vertebrae as the acupressure
load can be equally distributed due to the design that the internal projector can
be rotated in a certain angle to the up/down/left/right.
Conveniently Designed External Projector
External projector is designed in a size conveniently held and used with a hand,
which can be stored in a projector pocket nicely during no use.
Internal Driving Method with Low Noises
There are few noises thanks to the minimized friction between the internal
projector and rail due to the specially designed guard rail which can be used
semi-permanently by minimizing the driving load.
Convenient Remote Controller Holder
7KHUHPRWHFRQWUROOHUKROGHUSRVVLEOHRIÛURWDWLRQFDQEHXVHGFRQYHQLHQWO\LQDQ\
desired angle by the user.
Multifunctional Remote Controller Integrated into One
Buttons in a size that can be identified at a glance are easy to use with less wear
due to the special materials, and button descriptions cannot be easily erased.
Special Heater and Tourmanium
The tourmanium mat is combined to the special heater.
How to refer to cautions for
safety
Refer to cautions to be kept during
the product use.
(Refer to Page 3 in this User Manual
for more details.)
How to Install the Product
(Refer to Page 24 in this User Manual
for more details.)
How to use the product
(Refer to Page 28 in this User Manual
for more details.)
How to check out the product
components
(Refer to Page 10 in this User Manual
for more details.)
How toAssemble the
Product Frame
(Refer to Page 20 in this User Manual
for more details.)

NM-5000
Product Introduction

Product Frame ComponentsProduct Components
Introduction
Main mat Sub mat External projector
Product frame
External cloth
Projector covers Connection cable
for sub mat Power cord User manual
Low frequency pad Abdominal band for
low frequency pad Towel for low frequency pad
Remote controller Remote controller holder
(included in the frame
packing box)
Projector pocket Handle frame(2EA)
Main base frame
Main angle frame Sub angle frame
Frame leg fixing pipe
Frame legs(4EA)
Please check out whether all the components are in hand before
installing the product.
Please inquire of your supplier if there is any missing or damaged component.
Some specifications and/or designs are subject to change for improving the product
performance.

NM-5000

http://www.nuga.kr
NM-5000
User Manual
Thankyou for purchasing this product.
Beforeuse...
Pleaseread through cautions for safety in the
usermanual to use this product safely.
Tourmanium Product
QualityWarranty Enclosed
[ENGLISH ]
Product Introduction
i

9
9
9
9
9
9
9
Buffer rubbers
L-wrench

BoltA
Screws and components for assembly
Bolt D
Spanner tool(M12, 13)
Set screw bolt C
Nut B

NM-5000
Product Introduction

Names and Functions of
Product Components
The sub heater positioned on top of the sub mat increases the heating
effects by combining the tourmanium mat.
ⴙSub heater
Temperature can be set by turning a dial to the desired position.
ⴛTemperature setter for
sub heater Aremote controller, external projector and low frequency pad are connected
to the main assembly.
ⴜConnector bay
Low frequency pad has various functions including the relief from pain, etc.
ⴚLow frequency pad
Both the main mat and sub mat are horizontally built, which can be used
more conveniently with the attachment of a handle to be
controlled in step
UHVSHFWLYHO\IRUWKHGHVLUHGDQJOHRIÛÛRUÛ
Ceramics are separately built in around the cervical vertebrae as the
acupressure load can be equally distributed due to the design that the internal
projector can be rotated in a certain angle to the up/down/left/right. In addition,
there are few noises thanks to the minimized friction between the internal
projector and rail due to the specially designed guard rail which can be used
semi-permanently by minimizing the driving load.
ⴟProduct frame
ⴠInternal projector
External projector is designed in a size conveniently held and used with
a hand, which can be stored in a projector pocket nicely during no use.
ⴝExternal projector
and projector pocket
Buttons in a size that can be identified at a glance are easy to use and
button descriptions cannot be easily erased due to the use of special
PDWHULDOV,QDGGLWLRQWKHUHPRWHFRQWUROOHUKROGHUSRVVLEOHRIÛURWDWLRQ
can be used conveniently in any desired angle by the user.
ⴞRemote controller and
its holder
Name Function
The connection for the
power supply on the main
assembly and the power
input to the special heater
ྙ
ྡInternal projector
ⴘThe connection for the power
supply on the main assembly
and the power input to the
special heater
ྞExternal projector
and projector pocket
ྛLow frequency pad ྜTemperature setter
for sub heater
ྚSub heater
The power supply and signals are exchanged by connecting the power
supply cable to both the main mat and sub mat.
ྜྷConnector bay
ྟRemote controller and its holder
ྠProduct frame

NM-5000

HIGH
LOW
Product Introduction

/
6
(
"
#
&
4
5
NM-5000
Before the Product Installation
How toAssemble the Product Frame
How to Install the Product
Test Operations after Installation
18
20
24
26
Product Installation and
Preparations
Power button
Button to turn on/off the
power supply for the product
and internal projector
Temperature
Control Button for
Internal Projector
Button to increase or decrease
temperature of internal
projector
Auto/Manual
Switch Button
Button to set the operating
mode for the internal projector
toAuto/Manual
Button to set the
operating mode
for the internal
projector to
Auto/Manual
Window to display temperature
and error message of internal
projector
(refer to Page 41 for error
messages)
Manual Mode
Button for Internal
Projector
Button to adjust the position of
internal projector up/down
during the manual mode setting
Power Button for
External Projector
Button to turn on/off the power
supply for the external
projector
Power Button for
Low Frequency
Pad
Button to turn on/off the
power supply for the low
frequency pad
Temperature
Control Button
for External
Projector
Button to increase or
decrease temperature of
external projector
Indicator Window
for Temperature
and Condition of
External Projector
Window to display temperature
and error message of external
projector (refer to Page 41 for
error messages)
Button to control
the strength of
low frequency
Button to control the strength
of low frequency to a range of
strong ~ weak in the low
frequency pad
AUTO
CONT
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
Descriptions for Remote
Controller Buttons

NM-5000
POWER AUTO
PROJECTOR LOW FREQ
POWER
PROJECTOR
LOW FREQ
AU
T
O
M
A
N
TEMP
MANUAL
A
P
OWER AU
T
O
A
N
P
JT
L
/F
TEMP
M
i
n
Max
M
i
d
CO
N
T
P
ROJECTO
R
L
OW FRE
Q
F
P

Install the product in a flat floor.
Otherwise, it might damage the product. Connect the power supply after connecting
the remote controller first.
Otherwise, it might cause damage to the product.
Do not install the product in a place with the
frequent access.
(Otherwise, the product might be damaged.)
Do not install the product in a place with
much moisture or water.
(Otherwise, the product might be damaged.)
Be careful not to expose the product to the
direct sunlight.
(Otherwise, the product might be damaged.)
Do not drop or shock the product.
Otherwise, it might damage the product.
Check out the applied voltage before any use.
Otherwise, it is likely that the electrical shock
or fire occurs.
Do not place any inflammable substance on the
product, such as candle light or cigarette light.
Otherwise, it is likely to cause the electrical
shock or fire.
Avoid using the product in a closed place
with any fuel and/or chemical.
Otherwise, it might cause injuries or fire.
Move the product after separating the
power supply from connecting lines if the
product is moved.
Before the Product Installation

NM-5000
Product Installation and Preparations


How to connect frame
legs to the handle frame.
Insert frame legs (2 pieces) into
the handle frame as shown in
the picture.
Please note that the instructed
corner direction should be
oriented to the same direction
during the insertion.
Assemble frame legs and the
handle frame in the same way.
How to fix the main angle
frame
Place the main angle frame on the
base frame as shown in the picture.
Fasten a set screw bolt C (1 piece)
and nut B (2 pieces) after inserting
the hook into ‘Q’ here.
Completely fasten screws here, which
have not been completely fastened
in No. 3 assembly sequence.
How to fix the sub angle
frame.
Place the sub angle frame on the
base frame as shown in the picture.
Fasten a set screw bolt C (1 piece)
and nut B (2 pieces) after inserting
the hook into ‘Q’ here.
Completely fasten screws here.
How to insert the buffer rubbers.
Insert the buffer rubbers into ‘R’’ in
the picture.
How to fix frame legs.
Fix 2 pieces of frame leg fixing
pipes with 4 pieces of boltAas
shown in the picture and then
fix it with a piece of L-wench (T-1).
Do not fasten bolts completely
here.
Main base frame
Fix the main base frame with
boltA (16 pieces) and nut B
(16 pieces) using an L-wrench
as shown in the picture.
Do not fasten bolts completely
here.







ⲱ2Ⲳ


ⲱ3Ⲳ
ⲱ2Ⲳ
How toAssemble the Product Frame
Handle frame
L-wrench
T-1
L-wrench
T-1
Bolt A
Bolt A
Bolt A BoltA
Set screw bolt C
Set screw bolt C
Set screw bolt C
Nut B
Nut B
Nut B
Set screw bolt C Nut B
Nut B
Nut B
Main base frame
Sub angle frame
Frame leg fixing pipe
Frame legs
Frame legs
Frame leg fixing pipe
Main base frame
Hook
Hook
Buffer rubbers

NM-5000

Main angle frame
Product Installation and Preparations

 


ⲱ4Ⲳ
ⲱ4Ⲳ
Bolt D
Bolt D
BoltA
Nut B Nut B
Nut B
How to fix the entirely
assembled frame.
Fix the frame by fastening bolt
D (2 pieces) and nut B
(2 pieces) after setting the main
base frame, main frame and sub
frame as shown in the picture.
How to fix the entire bolts
again.
Fasten the entire bolts and nuts
tightly once again after the
assembly is completed.
Completed appearance
How to assemble the
remote controller holder.
Fasten boltA (1 piece) and
nut B (1 piece) after inserting
the remote control holder into
the instructed ‘S’ position.
L-wrench
T-1
How toAssemble the Product Frame

NM-5000
Product Installation and Preparations








ⴘⴙⴚ
How to Install the Product
Prepare product components
Take out the remote controller, power
cord, external projector, projector
pocket, and low frequency pad.
Connect to the connector
bay
ྙRemote controller
ྚExternal projector
ྛLow frequency pad
Connect components sequentially.
Connect the mat cable
Connect the power supply cable
for the sub mat to both the main
and sub mats as shown in the
picture.
Turn on the power supply
in the product
Turn on the power switch after the
power supply cord is connected to
the power input on the side of the
main mat.
Set temperature to the sub
heater
Turn the dialer to set the desired
temperature in the sub heater
attached to the side of the sub mat.
Tighten the product frame
to the mat
Attach the connecting band after
placing and tightening both the
main and sub mats to the product
frame.
Caution
Turn off the power switch when the
power is connected.
Otherwise, it might cause failure.
Caution
Keep the groove upward to the cable
connection.
Malfunctions might occur, if the groove
is not aligned accurately during the
cable connection.

NM-5000

HIGH
LOW
Product Installation and Preparations





NM-5000
Test Operations after Installation
Power switch
in the main assembly
Controller for main assembly Controller for external projector
Check out the power
supply for the product
Turn on the power switch.
Check out operations of
remote controller
ྙPress the power button on the
remote controller
ྚAdjust temperature for the
internal projector (+ / – button)
ྛAdjust temperature for the
external projector (+ / – button)
Refer to ‘How to Use the Remote
Controller’for each mode
(Page 28)
Check out operations of
sub heater
Turn the dialer to set the desired
temperature in the sub heater
attached to the side of the sub
mat.
Use the product
Lay yourself down with your legs
toward the sub mat and press the
Auto button in the remote
controller for the automatic
operations in the product.
You may use the product while
laying yourself down the other
way around.
Caution
Ensure the power supply to be
turned off after use or during no use.
Otherwise, it might cause failure.
How to Use the Remote Controller
How to Use the Product by Mode
How to Use the External Projector
How to Use the Low Frequency Pad
How to Use the Product
How to Set Temperature for the Sub Heater
28
28
33
34
36
38
How to Use the Product
AUTO MANU
TEMP
MANUAL
ⴚ
ⴘ
ⴙ

NM-5000
OnOff
POWER AUTO
PROJECTOR LOW FREQ
PJT
HIGH
LOW

/
6
(
"
#
&
4
5
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
/
6
(
"
#
&
4
5
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
PROJECTOR LOW FREQ
POWER AUTO
How to Use the Remote Controller
- How to Use the Product by Mode
Auto ྙMode
Round-trip acupuncture
function Round-trip massage function
Power supply Auto ⴙMode
Temperature control
Auto ྙMode
ྚPress theAuto button to operate
the internal projector.
No separate operation is necessary
in the middle as the product stops
automatically after operations.
The product automatically stops after
round-trip acupuncture operations for
about 38 minutes.
Auto ⴙMode
ྚPress theAuto button twice in a
row to operate the internal projector.
No separate operation is necessary
in the middle as the product stops
automatically after operations.
The product automatically stops after
round-trip massage operations for about
38 minutes.
Press theAuto button to operateAuto
ྚMode while Auto ྙMode is
operating.
Power supply
Temperature control
PROJECTOR LOW FREQ
POWER AUTO
POWER AUTO POWER AUTO
POWER AUTO POWER AUTO
POWER AUTO POWER AUTO

NM-5000
How to Use the Product
ⴘPress the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
ⴘPress the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
ྛControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· Range of temperature setting for
internal projector: 40~70୅
· Temperature setting unit
40~55୅: Temperature setting per 5୅
55~70୅: Temperature setting per 1୅
ྛControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· Range of temperature setting for
internal projector: 40~70୅
· Temperature setting unit
40~55୅: Temperature setting per 5୅
55~70୅: Temperature setting per 1୅

N
U
G
A
B
E
S
T
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
PROJECTOR LOW FREQ
POWER AUTO
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
N
U
G
A
B
E
S
T
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
AUTO MANU
TEMP
MANUAL
AUTO MANU
TEMP
MANUAL
PROJECTOR LOW FREQ
POWER AUTO
POWER AUTO
POWER AUTO
AUTO MANU
TEMP
MANUAL
How to Use the Remote Controller
- How to Use the Product by Mode
Temperature control Temperature control
Auto ྛMode
ⴙ3UHVVŸEXWWRQWZLFHLQDURZWR
operate the internal projector. No
separate operation is necessary in
the middle as the product stops
automatically after operations.
The product automatically stops
after round-trip massage
operations between the central
thoracic vertebrae and cervical
vertebrae for about 38 minutes.
Auto ྛMode
Massage function between the
thoracic vertebrae and
cervical vertebrae
hGྜGt
ⴙ3UHVVźEXWWRQWZLFHLQDURZWR
operate the internal projector. No
separate operation is necessary
in the middle as the product stops
automatically after operations.
The product automatically stops
after round-trip massage
operations between the central
thoracic vertebrae and vertebrae
lumbales for about 38 minutes.
Auto ྜMode
Massage function between the
thoracic vertebrae and
vertebrae lumbales
Power supply Power supply

NM-5000

POWER AUTO
POWER AUTO
POWER AUTO POWER AUTO
ⴘPress the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
ⴘPress the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
ྛControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· Range of temperature setting for
internal projector: 40~70୅
· Temperature setting unit
40~55୅: Temperature setting per 5୅
55~70୅: Temperature setting per 1୅
ྛControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· Range of temperature setting for
internal projector: 40~70୅
· Temperature setting unit
40~55୅: Temperature setting per 5୅
55~70୅: Temperature setting per 1୅
How to Use the Product

AUTO MANU
AUTO MANU
TEMP
MANUAL
TEMP
MANUAL
N
U
G
A
B
E
S
T
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
PROJECTOR LOW FREQ
PROJECTOR LOW FREQ
PROJECTOR LOW FREQ
POWER AUTO
N
U
G
A
B
E
S
T
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
Temperature control
AUTO MANU
TEMP
MANUAL
How to Use the Remote Controller
- How to Use the External Projector
Applied to the specific area
Caution
ྛApply to the desired area.
· Put the projector covers on before
applying it.
ྜEnsure the projector covers to
be covered while the external
projector is being used.
· Be aware that any direct contact
from the projector to the skin during
the high temperature setting might
cause burns.
ྙPress the projector button.
· Check out the connecting conditions
of the projector.
· Press the projector button once: On
Press it once again: Off
Operations
Temperature control
ྚControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· The projector is not turned on of the
actual temperature is higher than the
setting temperature, which is not meant
to be any failure.
· Temperature setting unit
40~55୅:Temperature setting per 5୅
55~70୅:Temperature setting per 1୅
Manual Mode
Manual Mode
ྚUse the product after placing the
internal projector at the desired
position with manual button
ŸźGXULQJWKHPDQXDOPRGH
The internal projector moves
ZKLOHŸźLVEHLQJSUHVVHG
Ÿ7KHLQWHUQDOSURMHFWRUPRYHV
to the cervical vertebrae.
ź7KHLQWHUQDOSURMHFWRUPRYHV
to the vertebrae lumbales.
ⴘPress the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
Power supply

NM-5000

PROJECTOR LOW FREQ
POWER AUTO
POWER AUTO
POWER AUTO
POWER AUTO
.PWJOH
QBUI
ྛControl temperature with +/- button.
(Moderate temperature: 55~60୅)
· Range of temperature setting for
internal projector: 40~70୅
· Temperature setting unit
40~55୅:Temperature setting per 5୅
55~70୅:Temperature setting per 1୅
How to Use the Product

N
U
G
A
B
E
S
T
AUTO
PJT L/F
MANU
TEMP
TEMP
Min Max
Mid
CONT
MANUAL
PROJECTOR LOW FREQ
PROJECTOR LOW FREQ
PROJECTOR LOW FREQ
POWER AUTO
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
PJT L/F
TEMP
Min Max
Mid
CONT
How to Use the Remote Controller
- How to Use the Low Frequency Pad
Connection Power supply
Strength control
ྜPress the low frequency button to
turn on the power supply for the low
frequency pad.
(Initial setting is set to ‘Weak 1’.)
· Check out the connecting conditions
of the low frequency pad.
· Press the low frequency button once: On
Press it once again: Off
ྙConnect an abdominal band to the
hole in both sides of the low
frequency pad.
ྛWear the abdominal band after
fixing the low frequency pad in a
good manner.
ྚWear the low frequency pad and
abdominal band after wetting the
towel for the low frequency pad or
a piece of 100% cotton towel or
cloth with water, and placing it on
the belly before wearing the low
frequency pad, if there is no gel at
home.
· Use a piece of towel or cloth after
squeezing it out completely to
prevent it from flowing water when it
is wetted with water.
ⴜControl the strength of low
frequency with the strength
button. (Refer to the following.)
Surface to contract the belly
The low frequency pad is a device to
improve scleritic pain or amyotrophia
by applying weak current to the
human body.
What is the low frequency pad?
Various wearing methods
You may wear it around any area other than the abdominal area.
Towel for the low frequency pad
Weak 1:
Green lighting Weak 2: Green blinking
Middle 1:
Yellow lighting Middle 2:
Yellow blinking
Strong 1:
Red lighting Strong 2:
Red blinking
The low frequency pad automatically stops
after operations for about 40 minutes.

NM-5000
How to Use the Product

Set angle upward Set angle downward
How to Use the Product
How to control angle
Basic use
Caution
Ensure using the projector covers while
applying the external projector.
Be aware of burns if the product is
applied to a part in the human body for
a long time.
ⴘLay yourself down with the head to the
main mat and legs to the sub mat.
ⴙApply massage to your desired area
such as your arms with the external
projector during theAuto mode.
ⴚUse the product while you are laying
yourself down to the opposite side.
How to use while sitting
Simultaneous use for 2 persons
How to apply to the abdominal area
Caution
Ensure using the projector covers while
applying the external projector.
Be aware of burns if the product is applied
to a part in the human body for a long time.
Apply the proper temperature while using
the sub heater.
ྙApply massage with the external
projector after operating the product
in the same way as the basic use.
ྚ
Use the product after controlling temperature
for the sub mat while operations for the
main mat is being stopped.
ྙTwo persons can use the product
simultaneously with one person on the
product and another person with the
external projector while sitting.
ྙ6WHSZLVHFRQWUROE\ÛFDQEHGRQHZLWK
ÛÛRUÛLIWKHPDWDQJOHLVVHW
upward.
· Grab the product frame at the mat bottom
and then control stepwise to set upward.
ྚPull down attached to the product frame
if you want the mat angle downward.
Normal direction
Reverse direction
Main mat heating
Sub mat heating
Caution
Ensure using the projector covers while
applying the external projector.
Be aware of burns if the product is applied
to a part in the human body for a long time.
ྙLie on your face with the head to the
main mat and legs to the sub mat.
ྚPress the button with the remote controller
to move the internal projector to the
abdominal area. Lie on your face after
moving to the abdominal area.
ྛApply the heating function to the abdominal
area using the sub heater while laying
yourself down to the opposite direction.
Stop operating the main mat during this time.
Caution
Do not apply the product to the breast but only
to the abdominal area manually during
PDVVDJHWRWKHDEGRPLQDODUHD2WKHUZLVHLW
might cause damage to the human body.
Sub mat heating
Main mat heating
&RQWURODQJOHLQÛÛRUÛ
Angle control can be done to both directions.
[ ]
Hook handle

NM-5000
How to Use the Product

NM-5000
How to Set Temperature
for the Sub Heater
How to use temperature setter for sub heater
Turn the dial to the desired position to set temperature.
(30~65୅)
How to Store and Clean the Product after Use
Check Indicator Window of Remote Controller
How to Take EmergencyActions during Use
Self-check Items
Before anyA/S Request
Product Specifications
Memo
Product Warranty
40
41
42
43
44
45
46
47
Product Storage and Care
Sub heater
Temperature setter
for sub heater

NM-5000
HIGH
LOW
HIGH
LOW