NUTRIBULLET BLENDER COMBO Series User manual

User guide.
BLENDER
COMBO
®
NBF07500-1210DG_UG BD-IM035_F200821.indd 1 8/21/20 12:35 PM

2
Important safeguards &
cautionary information.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your NutriBullet®. When using any
electrical appliance, basic safety precautions should always
be observed, including the following critical information.
PERSONAL SAFETY
BLENDING WITH
NUTRIBULLET
®
CUPS:
NEVER put hot liquids
in any of the blending
cups before blending.
Start with cold or room
temperature ingredients.
Heated ingredients can
create internal pressure in a
sealed blending cup, which
may erupt on opening and
cause thermal injury.
Never blend carbonated
ingredients or liquids. Built-
up pressure can cause the
blade and cup to separate,
possibly resulting in
personal injury.
If storing blended ingredients,
remove the blade from the cup
and replace with the fl ip top lid.
Never store the extractor
blade on the power base
without a cup or vessel
attached. Failure to do so may
results in personal injury if the
unit is accidentally turned on.
NEVER leave spoons or other
foreign objects in the cup
before blending. Failure to do
so will result in damage to the
cup and/or possible personal
injury.
BLENDING WITH
THE PITCHER:
HOT LIQUIDS:
Use caution when
blending hot liquids
in the pitcher.
Never turn the power on while
using the pitcher without the
vented lid cap inserted and
locked into the pitcher lid, as
ingredients can splash, and if
hot or warm, could potentially
cause thermal injury and/or
property damage.
Friction from the rotating
blade will cause ingredients
to heat and generate internal
pressure in the sealed vessel.
Do not continuously operate
for more than one minute. If
the vessel is warm to touch,
allow to cool before carefully
opening pointed away from
your body.
WARNING!
WARNING!
WARNING!
CUP
PITCHER
WARNING!
NBF07500-1210DG_UG BD-IM035_F200821.indd 2 8/21/20 12:35 PM

3
NEVER leave spoons or other
foreign objects in the pitcher
before blending. Failure to
do so will result in damage to
the pitcher and/or possible
personal injury.
Never leave the NutriBullet®
unattended while it is in use.
Close supervision is necessary
when any appliance is used by
or near children.
To avoid risk of electric shock,
never immerse the cord, plug,
or power base of blender in
water or other liquids.
At all times, avoid contact
with moving parts.
VERY IMPORTANT: If there
is a liquid spill, immediately
disconnect the unit from the
power source. If the spill is
external only, clean with a
warm, soapy cloth and allow
the unit to dry completely
before operating.
If the spill has leaked in to
the internal components
of the power base, cease
use immediately. Unit must
be checked by a Qualified
Electrician and certified
electrically safe before using
again. Failure to do so will
results in possible shock and/
or personal injury.
This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
Switch o the appliance and
disconnect from power supply
before changing accessories or
handling moving parts.
To reduce the risk of personal
injury or damage to the device,
keep hands and utensils away
from the cutting blade.
The cup, pitcher and blades are
consumable components. Over
time, if the unit starts to get
louder or make unusual noise or
vibration, it indicates that these
consumable parts may need
replacing.
The continued use of worn parts
may results in part failure and/or
personal injury.
WARNING!
NBF07500-1210DG_UG BD-IM035_F200821.indd 3 8/21/20 12:35 PM

4
WARNING!
If you are taking any medica-
tion, especially cholesterol-
lowering medication, blood
thinners, blood pressure drugs,
tranquilizers, or antidepres-
sants, please check with your
physician before consuming
any NutriBullet® recipes.
The following list of seeds and
pips contain chemicals that
release cyanide into the body
when ingested. Do not use the
following seeds and pips in
the NutriBullet®: apple seeds,
apricot seeds, cherry pips,
plum pips, and peach pips.
PRODUCT SAFETY
If the NutriBullet® malfunctions
or is dropped, or damaged in
any manner, discontinue use
and contact Customer Service
for further assistance.
To prevent overheating, never
allow the motor to run
continuously for more than one
minute.
If the motor stops for any reason,
unplug the power base and let it
cool for at least 15 minutes.
Never use the NutriBullet®
without adding liquid or when
the cup is empty, as doing so
may damage the blade.
TO AVOID LEAKAGE, DO
NOT OVERFILL THE CUP OR
PITCHER! The pitcher is marked
with two MAX lines: one for solid
ingredients (higher line) and
one for liquid ingredients (lower
line). Your NutriBullet® cups are
also marked with a MAX line.
When filling the cup or pitcher,
make sure your ingredients do
not exceed their respective MAX
lines.
The NutriBullet® is not intended
for use in microwave ovens. Do
not place the NutriBullet® cups,
power base or any accessories
in a microwave as this may result
in damage to the appliance.
WARNING!
NBF07500-1210DG_UG BD-IM035_F200821.indd 4 8/21/20 12:35 PM

5
Use of adapters and converters
is considered an unauthorized
modifi cation of the product
and as such will void the
warranty. Use of this product in
locations with di erent electrical
specifi cations may result in
damage to the product.
CAUTION: In order to avoid
a hazard due to inadvertent
resetting of the thermal cut-
out, this appliance must not
be connected to an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on and
o by the utility.
Periodically inspect cord and
plug for damage. Do not operate
any appliance with a damaged
cord or plug. If damaged,
it must be replaced by the
manufacturer, its service agent,
or similarly qualifi ed persons in
order to avoid a hazard.
Do not allow the cord to hang
over the side of the counter or
table.
Do not allow cord to touch hot
surfaces, including stove.
The use of any non-genuine
NutriBullet® accessories will void
the warranty.
WARNING:
VENTILATION CAUTION
Always operate the NutriBullet®
on a level surface, leaving
unobstructed space beneath
and around the power base to
permit proper air circulation.
Slots and openings on the
bottom of the product are
provided for ventilation to
ensure reliable motor operation
and to prevent over-heating.
WARNING: to prevent fi re
hazard, power base openings
should be free of dust or lint
and never obstructed with
fl ammable materials such
as newspapers, tablecloths,
napkins, dishtowels, or place
mats.
Extractor blades are
sharp! Handle carefully.
Use care while handling the
extractor blades. Do not
touch the extractor blade
edges to avoid injury.
Do not remove the seal from
your blade attachment. The
seal is not designed to be
removed. If seal is removed,
cease use immediately and
purchase a replacement.
If, over time, the easy-twist
extractor blade becomes loose
or damaged, you may order a
new easy-twist extractor blade
at: bulletbrands.com.au /
bulletbrands.co.nz or contact
customer service.
WARNING!
WARNING!
NBF07500-1210DG_UG BD-IM035_F200821.indd 5 8/21/20 12:35 PM

6
AVOID CONTACT WITH
MOVING PARTS! To reduce the
risk of severe personal injury,
keep hands and utensils out of
and away from the cross blade
while blending food.
The use of attachments not
recommended or not sold by
the manufacturer may cause
fi re, electric shock, or injury.
TO REDUCE THE RISK OF
PERSONAL INJURY OR
PROPERTY DAMAGE, make
sure the easy-twist extractor
blade is securely twisted (hand-
tightened) onto the NutriBullet®
blending cup before placing it on
the motor base. Check to make
sure the easy-twist extractor
blade is aligned properly before
placing it on the motor base and
operating your NutriBullet®.
Always operate
the pitcher with
the pitcher lid
securely in place.
With recipes that require added
ingredients to be incorporated
during blending, fi rst add the
base ingredients, seal the
pitcher lid with vented lid cap
attached, and begin blending.
Then, once the ingredients
are well mixed, twist open the
vented lid cap and carefully
pour or drop ingredients into
the mixture.
If you need to push ingredients
closer to the blade, ONLY USE
THE TAMPER PROVIDED with
the NutriBullet® Select 1200.
DO NOT use any apparatus
other than the tamper to push
ingredients toward the blade.
The tamper is specifi cally
designed not to come in contact
with the blade. Spatulas, spoons
and other tools can make
contact with the blade, which
may result in damage to the
machine, damage to property,
and/or possible injury.
NEVER USE YOUR FINGERS OR
ANY PART OF YOUR HAND TO
PUSH INGREDIENTS DOWN
TOWARD THE BLADE. Only use
the provided tamper.
The cyclonic action® of your
NutriBullet® requires the use
of liquids to make smoothies
and other nutritious items. The
NutriBullet® is not intended to be
used without liquids, or as an ice
crusher. ALWAYS ADD LIQUID to
your recipe.
We recommend replacing your
easy-twist extractor blade
every 6 months (depending on
use) or as needed for optimal
performance.
PITCHER
NBF07500-1210DG_UG BD-IM035_F200821.indd 6 8/21/20 12:35 PM

7
Blade attachments should not
be placed in the dishwasher for
cleaning. Exposure to hot water
can cause damage to the seal in
the outer rim of the attachment.
Do not u se NutriBull et® outdo ors.
If exposed to inclement weather
elements such as rain or other
wet conditions, discontinue use.
Unplug the NutriBullet® when
it is not in use. Make sure the
power base is unplugged before
assembling, disassembling,
adding additional parts, or
cleaning.
Never remove cup/blade
assembly from the power
base until the motor comes to
a complete stop. Removing
the cup/blade assembly while
power base is still running
may cause damage the blade
coupling or motor gear.
Periodically inspect your
NutriBullet® cups for damage
or wear that may impair proper
function. Discontinue use and
replace components if you
detect cracking, crazing or
cloudiness/discolouration, or
other damage to the plastic
cups, or tabs (on the side of
the cup). You may purchase
new cups and cross blades
at www.bulletbrands.com.
au, nutribullet.co.nz or by
contacting Customer Service.
!
Save these
instructions!
FOR HOUSEHOLD
USE ONLY
NBF07500-1210DG_UG BD-IM035_F200821.indd 7 8/21/20 12:35 PM

8
NBF07500-1210DG_UG BD-IM035_F200821.indd 8 8/21/20 12:35 PM

9
Contents.
Thank you for purchasing the NutriBullet®
Blender Combo.
10 What’s included
11 Assembly guide
12 Getting started
12 Safety guide
13 Pitcher assembly & use
16 NutriBullet® cup assembly & use
18 Blending control panel.
19 How to use the blending control panel
20 Care & maintenance.
20 How to clean the NutriBullet®
22 How to store
22 Replacement parts
23 NutriBullet® Blender Combo’s
one-year limited warranty
NBF07500-1210DG_UG BD-IM035_F200821.indd 9 8/21/20 12:35 PM

10
What’s included.
900 mL
cup
pitcher with
integrated blade
motor base pitcher lid
with vented
lid cap
tamper
700 mL
handled cup
500 mL
cup
2 to-go lidseasy-twist
extractor blade
NBF07500-1210DG_UG BD-IM035_F200821.indd 10 8/21/20 12:35 PM

11
Assembly guide.
NutriBullet®
cup
vented lid cap
pitcher lid
pitcher
easy-pour spout
tamper
integrated blade
blender control
panel
motor base
suction cup feet
easy-twist
extractor blade
NBF07500-1210DG_UG BD-IM035_F200821.indd 11 8/21/20 12:35 PM

Use extra caution when
blending hot liquids in
the pitcher.
Steam and splatters can escape
through the vented lid, potentially
causing scalding and/or burns.
NEVER blend hot liquids in your
pitcher without the pitcher lid
and vented lid cap attached. The
vented lid cap is ventilated to allow
steam and pressure to release,
while guarding against excess
splashing. NEVER blend hot liquids
in your Nutribullet cups or any
other sealed vessel.
When blending hot liquids, add
liquid and solid ingredients to your
pitcher below their respective MAX
lines. Attach the pitcher lid with the
vented lid cap inserted. Press the
POWER icon, then begin blending on
the LOW setting. Once ingredients
are integrated and the mixture is
level (no splashing), increase speed
as needed.
PLEASE KEEP
THESE IMPORTANT
SAFEGUARDS IN
MIND WHEN USING
THE APPLIANCE:
• Make sure the base is plugged in
for use.
• DO NOT attempt to operate the pitcher
on the appliance without attaching
the pitcher lid and vented lid cap.
• Never run the appliance while empty.
• Appliance accessories are not
intended to be used in the microwave
as it may damage the accessories.
• Never leave the appliance
unattended while in use.
Never blend hot ingredients
when using any sealed
NutriBullet® cups.
Heated ingredients can pressurize
sealed containers when agitated
and violently expel hot contents upon
opening. Always start the blending
process with room temperature or
refrigerated ingredients and liquids
(21°C/70°F or cooler).
WARNING!
WARNING!
Getting started.
12
NBF07500-1210DG_UG BD-IM035_F200821.indd 12 8/21/20 12:35 PM

13
Pitcher assembly
& use.
Place the pitcher onto the
motor base — handle facing
to the right of the blending
control panel, never towards
the back — and gently twist
clockwise so it locks in place.
When you hear the click, it’s
locked and ready to blend.
NOTE: If you are left-handed, place
the handle facing towards the center
of the blending control panel and
twist clockwise.
5
3
Place the pitcher on a
clean, dry, level surface.
Add the ingredients to the
pitcher, making sure they do
not exceed the MAX line.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg 2-5) and on
the previous page before
proceeding to Step 2.
Place the motor base on
a clean, dry, level surface
such as a counter or table.
4Place the pitcher lid with
vented lid cap attached on
the pitcher, making sure it’s
aligned to the handle.
NOTE: Always add liquid. The
blending pitcher is marked with
two MAX lines: one for solid
ingredients (higher line) and
one for liquids (lower line). When
fi lling the blender, make sure your
ingredients do not exceed their
respective MAX lines.
2
NBF07500-1210DG_UG BD-IM035_F200821.indd 13 8/21/20 12:35 PM

14
6
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
7
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed defi nitions.
CAUTION: Do not use any
apparatus other than the
tamper to push ingredients
toward the blade. The tamper
is specifically designed not to
come in contact with the blade.
Spatulas, spoons and other
tools are long enough to reach
the blade, which may result
in damage to the machine,
damage to property, and
possible injury.
NOTE: If you need to add
additional ingredients while
blending, switch the setting to
LOW and remove the vented
lid cap from your pitcher lid,
leaving the lid attached. Add
ingredients through the hole
in the top of the lid, followed
by the tamper if necessary.
Replace the vented lid cap, then
increase to your desired speed.
DO NOT attempt to add items
through the vent hole when
blending hot ingredients.
NBF07500-1210DG_UG BD-IM035_F200821.indd 14 8/21/20 12:35 PM

15
Twist pitcher counterclockwise
and lift o the motor base.
Pour and enjoy!
Press POWER to turn o
the unit completely.
If the ingredients stick to
the side of the pitcher, stop
the appliance by pressing
POWER and wait for
the blade to stop turning.
Then remove the pitcher
lid and use the tamper to
dislodge the ingredients.
When fi nished, replace the
lid and continue blending.
if the ingredients continue
to stick, consider adding a
little more liquid.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
WARNING: Blades are sharp. Never
insert your hands into the pitcher.
8
9
11
10
NBF07500-1210DG_UG BD-IM035_F200821.indd 15 8/21/20 12:35 PM

16
Handle the easy-twist extractor
blade assembly with care, as
the blades are sharp.
Never leave the appliance
unattended while in use.
NEVER BLEND HOT
INGREDIENTS, as doing
so may cause excessive
pressure buildup, resulting in
risk of personal injury and or
property damage.
NutriBullet® cup
assembly & use.
WARNING!
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
5
Add ingredients and liquid
to the NutriBullet® cup.
NOTE: Always add liquid. Do not
overfi ll! To avoid leakage, do not add
ingredients beyond the MAX line.
3
4
Twist the easy-twist
extractor blade onto the
cup until tightly sealed.
1 Review all warning and
caution statements in the
Important Safeguards
section (pg 2-5) before
proceeding to Step 2.
2 Place the motor base on
a clean, dry, level surface
such as a counter or table.
6
Turn the cup upside down
and place it onto the motor
base, gently turning the
cup clockwise to lock into
the motor base.
NBF07500-1210DG_UG BD-IM035_F200821.indd 16 8/21/20 12:35 PM

7
8
10
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 16 for
speed defi nitions.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
NOTE: speeds will automatically
shut o after 60 seconds.
Unlock the assembly by
gently twisting the cup
counterclockwise. You will
hear a click. Enjoy!
NOTE: Blending should not require
longer than one minute to yield
smooth and creamy results.
Press POWER to turn o
the unit completely.
9
CAUTION
Do not remove the easy-twist
extractor blade from the
NutriBullet® cup until blending
has completely ceased. Do not
use the easy-twist extractor blade
as a storage lid for your cup.
Some foods may contain active
ingredients or release gases that
will expand if left in a sealed
container, resulting in excessive
pressure buildup that can pose
a risk of injury. When storing
contents in the cup, use plastic
wrap or foil to seal your container.
Always point contents away from
your body when unsealing.
17
NBF07500-1210DG_UG BD-IM035_F200821.indd 17 8/21/20 12:35 PM

18
Blending control panel.
TURNING ON/OFF
The power button actuates
the master power of the
appliance. When pressed, this
button lights up to indicate the
motor is powered on, and the
other functions can be used.
Always turn the master power
o and unplug the unit when
the machine is not in use.
LOW SPEED
Use to mix thin batter,
gravies, marinades; scramble
eggs; process cooked foods
and uncooked fruits.
THE EXTRACT PROGRAM
Use to break down whole
fruits, vegetables, and ice into
nutrient-rich smoothies. This
button will activate a run cycle
that shuts o automatically.
MEDIUM SPEED
Use to cream soups, mix
dips, grind nuts, and
blend sauces, spreads,
mixed drinks, powdered
drinks, and milkshakes.
NBF07500-1210DG_UG BD-IM035_F200821.indd 18 8/21/20 12:35 PM

19
WARNING!
NEVER BLEND HOT INGREDIENTS IN ANY SEALED NUTRIBULLET® CUP
Doing so may cause excessive pressure buildup, resulting in risk of personal
injury or property damage. Hot items should only be blended in the pitcher
using proper safeguards.
HIGH SPEED
Use to liquefy thick
mixtures and blend frozen
fruits and vegetables.
PULSE*
Use to control chopping
and processing.
WARNING: DO NOT
use this setting with
hot ingredients!
How to use the blending control panel.
LOW, MEDIUM OR HIGH
Select a speed and press once
to turn on. The button will
illuminate. To pause/stop the
unit, press the button a second
time — it will de-illuminate — or
press POWER . While in the
idle-mode, the POWER button
will remain lit. To fully power
down after pausing, press
POWER and unplug the unit.
NOTE: If using the pitcher, speeds
will run until paused/stopped. If using
the NutriBullet® cups, speeds will
automatically shut o after 60 seconds.
THE EXTRACT PROGRAM
Press the EXTRACT button
and the NutriBullet® Blender
Combo will do the work for you.
This program automatically
stops at the end of its cycle. To
pause or stop the blender, press
EXTRACT again or POWER .
PULSE
Press and release the PULSE
button to chop ingredients. If
you hold this button down, it will
continue to run until you release it.
NBF07500-1210DG_UG BD-IM035_F200821.indd 19 8/21/20 12:35 PM

20
Care & maintenance.
MOTOR BASE:
• To avoid risk of injury, NEVER
attempt to clean the actuator
system on the motor base
while the NutriBullet® Blender
Combo is plugged in.
• Do not attempt to remove any
pieces from the motor base.
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the
motor base until clean.
• If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
• To clean leakage residue
from the motor base, wipe
with a damp sponge and
warm water.
• If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
WARNING: Never submerge
the motor base in water.
Here’s how to clean
the NutriBullet®:
STEP 1:
The most important thing —
ALWAYS POWER OFF THE UNIT
and UNPLUG the motor base
from the power outlet when it
is not in use. Do not attempt to
handle the appliance until all
parts have stopped moving!
This includes during assembly
and disassembly, while
changing accessories during
cleaning, and any time you
leave the machine unattended.
STEP 2:
Detach the NutriBullet® cup /
easy-twist extractor blade or
pitcher from the motor base.
STEP 3:
Clean the individual
components (motor base,
easy-twist extractor blade,
NutriBullet® cups) as
recommended in the
following pages.
Cleaning the NutriBullet® is easy. The pitcher is dishwasher-safe while
the cups and to-go lids are TOP RACK dishwasher-safe. The easy-
twist extractor blade and motor base can be quickly hand-washed
with soap and water. Read on for best practices.
NBF07500-1210DG_UG BD-IM035_F200821.indd 20 8/21/20 12:35 PM