NUTRIBULLET Blender Combo User manual

User guide.

2
Important safeguards &
cautionary information.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your nutribullet®. When using any
electrical appliance, basic safety precautions should always
be observed, including the following critical information.
PERSONAL SAFETY
BLENDING WITH
NUTRIBULLET
®
CUPS:
Do not put hot liquids
in any of the blending
vessels before blending.
Start with cool or room
temperature ingredients.
Heated ingredients can
create internal pressure in a
sealed blending vessel, which
may erupt on opening and
cause thermal injury.
Never blend carbonated
ingredients or liquids.
Built-up pressure from
released gases can
cause container to burst,
resulting in possible injury.
Never permit any blended
mixture to sit inside a sealed
vessel without first releasing
internal pressure.
Never store the extractor blade
on the power base without a
cup or vessel attached.
BLENDING WITH THE PITCHER:
Use caution when blending
hot liquids in the pitcher.
Never turn the power on
while using the pitcher
without the vented lid cap
inserted and locked into the
pitcher lid, as ingredients
can splash, and if hot or
warm, could potentially
cause thermal injury and/
or property damage.
Friction from the rotating
blade will cause ingredients
to heat and generate internal
pressure in the sealed vessel.
Do not continuously operate
for more than one minute. If
the vessel is warm to touch,
allow to cool before carefully
opening pointed away from
your body.
Remove spoon or other foreign
objects before blending.
Never leave the nutribullet®
unattended while it is in use.
Close supervision is necessary
when any appliance is used by
or near children.
To avoid risk of electric shock,
never immerse the cord, plug,
or power base of blender in
water or other liquids.
At all times, avoid contact
with moving parts.
WARNING!WARNING!
WARNING!
WARNING!

3
This appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
Children should be supervised
to ensure that they do not play
with the appliance.
If the power supply cord is
damaged, it must be replaced
by the manufacturer, its
service agent or similarly
qualified persons in order to
avoid a hazard.
Switch o the appliance and
disconnect from power supply
before changing accessories
or handling moving parts.
To reduce the risk of personal
injury or damage to the
device, keep hands and
utensils away from the
cutting blade.
To reduce the risk of injury
and leakage, make sure
the blade base is securely
screwed onto the cup before
placing it on the power base
and operating the appliance.
Blades are sharp.
Handle carefully.
The use of attachments not
recommended or not sold by
the manufacturer may cause
fire, electric shock, or injury.
Do not allow blended mixtures
to sit for long periods in a
sealed container. The sugars
in the fruit and vegetables
can ferment, causing pressure
to build up and expand in
the vessel which can cause
ingredients to erupt and spray
out when moved or opened.
WARNING!
If you are taking any medi-
cation, especially cholesterol-
lowering medication, blood
thinners, blood pressure drugs,
tranquilizers, or antidepress-
ants, please check with your
physician before consuming
any nutribullet®recipes.
The following list of seeds and
pips contain chemicals that
release cyanide into the body
when ingested. Do not use the
following seeds and pips in
the nutribullet®: apple seeds,
apricot seeds, cherry pips,
plum pips, and peach pips.
PRODUCT SAFETY
If the nutribullet®malfunctions
or is dropped, or damaged in
any manner, discontinue use
and contact Customer Service
for further assistance.
To prevent overheating,
never allow the motor to run
continuously for more than one
minute at a time, as this may
cause damage to the motor
as well as increase the thermal
pressure inside the cup which
can cause personal injury.
Check gasket to make sure it is
completely seated in the
WARNING!

4
blade unit before each use. If seal
is damaged, replace the complete
blade assembly.
If the motor stops for any reason,
unplug the power base and let
it cool for at least 15 minutes as
this will reset the internal thermal
breaker.
Never use the nutribullet®Blender
Combo without adding liquid or
when the cup is empty, as doing
so may damage the blade.
The nutribullet®is not intended
for use in microwave ovens. Do
not place the nutribullet®cups,
power base or any accessories in
a microwave as this may result in
damage to the appliance.
Use of adapters and converters
is considered an unauthorized
modification of the product and
as such will void the warranty. Use
of this product in locations with
dierent electrical specifications
may result in damage to the
product.
CAUTION: In order to avoid
a hazard due to inadvertent
resetting of the thermal cut-
out, this appliance must not be
supplied through an external
switching device, such as a timer,
or connected to a circuit that is
regularly switched on and o by
the utility.
Periodically inspect cord and plug
for damage. Do not operate any
appliance with a damaged cord
or plug.
Do not pull, twist, or damage the
power cord.
Do not allow the cord to hang over
the side of the counter or table.
Do not allow cord to touch hot
surfaces, including stove.
The nutribullet®power base
is made exclusively to work
with the nutribullet®cups and
blades only and not other Bullet
branded products such as the
magic bullet®. Use with items
not specifically manufactured
for the nutribullet®will void
the warranty.
WARNING: VENTILATION
CAUTION
Always operate the nutribullet®
on a level surface, leaving
unobstructed space beneath
and around the power base to
permit proper air circulation.
Slots and openings on the bottom
of the product are provided for
ventilation to ensure reliable
motor operation and to prevent
over-heating.
WARNING: to prevent fire
hazard, power base openings
should be free of dust or lint
and never obstructed with
flammable materials such
as newspapers, tablecloths,
napkins, dishtowels, or
place mats.
Always operate the pitcher with
the pitcher lid securely in place.
With recipes that require certain
ingredients to be incorporated
during blending, first add the
base ingredients, seal the pitcher
lid with vented lid cap attached,
and begin blending. Then, once
the ingredients are well mixed,
twist open the vented lid cap and
carefully pour or drop ingredients
into the mixture.
WARNING!

5
If you need to push ingredients
closer to the blade, ONLY USE
THE TAMPER PROVIDED with
the nutribullet® Blender Combo.
DO NOT use any apparatus
other than the tamper to push
ingredients toward the blade. The
tamper is specifically designed
not to come in contact with the
blade. Spatulas, spoons and
other tools can make contact with
the blade, which may result in
damage to the machine, damage
to property, and/or possible injury.
NEVER USE YOUR FINGERS OR
ANY PART OF YOUR HAND TO
PUSH INGREDIENTS DOWN
TOWARD THE BLADE. Only use
the provided tamper.
The cyclonic action®of your
nutribullet®requires the use
of liquids to make smoothies
and other nutritious items. The
nutribullet®is not intended to be
used without liquids, or as an ice
crusher. ALWAYS ADD LIQUID to
your recipe.
The cup, pitcher and blades are
consumable components. We
recommend replacing your easy-
twist extractor blade every 6
months for optimal performance.
If, over time, the easy-twist
extractor blade becomes loose,
damaged, or needs replacing,
you may order a new easy-twist
extractor blade at: bulletbrands.
com.au / bulletbrands.co.nz or
contact customer service.
Do not use nutribullet®outdoors.
If exposed to inclement weather
elements such as rain or other
wet conditions, discontinue use.
Unplug the nutribullet®when
it is not in use. Make sure the
power base is unplugged before
assembling, disassembling,
adding additional parts, or
cleaning.
TO AVOID LEAKAGE, DO NOT
OVERFILL THE BLENDING
VESSELS! The pitcher is marked
with two MAX lines: one for solid
ingredients (higher line) and one
for liquid ingredients (lower line).
Your nutribullet®cups are also
marked with a MAX line. When
filling the blending vessels, make
sure your ingredients do not
exceed their respective MAX lines.
Exceeding the indicated MAXlines
can result in leakage, and may
lead to dangerous pressurization.
Never remove cup/blade
assembly from the power base
until the motor comes to a
complete stop. Removing the cup/
blade assembly while power base
is still running may cause damage
the blade coupling or motor gear.
CAUTION: The stainless steel
straws are to be used for
drinking only. NEVER place in
the nutribullet®cups or pitcher
when in operation. NEVER use the
stainless steel straws as a tamper.
Stainless steel straws could have
sharp edges, if this is the case,
please dispose of appropriately.
Save these
instructions!
FOR HOUSEHOLD
USE ONLY
!

6

7
Contents.
Thank you for purchasing the nutribullet®
Blender Combo.
08 What’s included
09 Assembly guide
10 Getting started
10 Safety guide
11 Pitcher assembly & use
14 nutribullet®cup assembly & use
16 Blending control panel.
17 How to use the blending control panel
18 Care & maintenance.
18 How to clean the nutribullet®
20 How to store
20 Replacement parts
21 nutribullet®Blender Combo’s
one-year limited warranty

8
What’s included.
900mL
cup
pitcher with
integrated blade
motor base
pitcher lid
with vented
lid cap
tamper
700mL
handled cup
2 to-go lids
easy-twist
extractor blade

9
Assembly guide.
nutribullet®
cup
vented lid cap
pitcher lid
pitcher
easy-pour spout
tamper
integrated blade
blender control
panel
motor base
suction cup feet
easy-twist
extractor blade

Use extra caution when
blending hot liquids in
the pitcher.
Steam and splatters can escape
through the vented lid, potentially
causing scalding and/or burns.
NEVER blend hot liquids in your
pitcher without the pitcher lid
and vented lid cap attached. The
vented lid cap is ventilated to allow
steam and pressure to release,
while guarding against excess
splashing. NEVER blend hot liquids
in your nutribullet®cups or any
other sealed vessel.
When blending hot liquids, add
liquid and solid ingredients to your
pitcher below their respective MAX
lines. Attach the pitcher lid with the
vented lid cap inserted. Press the
POWER icon, then begin blending on
the LOW setting. Once ingredients
are integrated and the mixture is
level (no splashing), increase speed
as needed.
PLEASE KEEP
THESE IMPORTANT
SAFEGUARDS IN
MIND WHEN USING
THE APPLIANCE:
• Make sure the base is plugged in
for use.
•DO NOT attempt to operate the pitcher
on the appliance without attaching
the pitcher lid and vented lid cap.
• Never run the appliance while empty.
• Appliance accessories are not
intended to be used in the microwave
as it may damage the accessories.
• Never leave the appliance
unattended while in use.
Never blend hot ingredients
when using any sealed
nutribullet®cups.
Heated ingredients can pressurize
sealed containers when agitated
and violently expel hot contents upon
opening. Always start the blending
process with room temperature or
refrigerated ingredients and liquids
(21°C/70°F or cooler).
WARNING!
WARNING!
Getting started.
10

11
Pitcher assembly
& use.
Place the pitcher onto the
motor base — handle facing
to the right of the blending
control panel, never towards
the back — and gently twist
clockwise so it locks in place.
When you hear the click, it’s
locked and ready to blend.
NOTE: If you are left-handed, place
the handle facing towards the center
of the blending control panel and
twist clockwise.
5
3
Place the pitcher on a
clean, dry, level surface.
Add the ingredients to the
pitcher, making sure they do
not exceed the MAX line.
1Review all warning and
caution statements in the
Important Safeguards
section (pg 2-5) and on
the previous page before
proceeding to Step 2.
Place the motor base on
a clean, dry, level surface
such as a counter or table.
4Place the pitcher lid with
vented lid cap attached on
the pitcher, making sure it’s
aligned to the handle.
NOTE: Always add liquid. The
blending pitcher is marked with
two MAX lines: one for solid
ingredients (higher line) and
one for liquids (lower line). When
filling the blender, make sure your
ingredients do not exceed their
respective MAX lines.
2

12
6
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
7
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 20 for
speed definitions.
CAUTION: Do not use any
apparatus other than the
tamper to push ingredients
toward the blade. The tamper
is specifically designed not to
come in contact with the blade.
Spatulas, spoons and other
tools are long enough to reach
the blade, which may result
in damage to the machine,
damage to property, and
possible injury.
NOTE: If you need to add
additional ingredients while
blending, switch the setting to
LOW and remove the vented
lid cap from your pitcher lid,
leaving the lid attached. Add
ingredients through the hole
in the top of the lid, followed
by the tamper if necessary.
Replace the vented lid cap, then
increase to your desired speed.
DO NOT attempt to add items
through the vent hole when
blending hot ingredients.

13
Twist pitcher counterclockwise
and lift o the motor base.
Pour and enjoy!
Press POWER to turn o
the unit completely.
If the ingredients stick to
the side of the pitcher, stop
the appliance by pressing
POWER and wait for
the blade to stop turning.
Then remove the pitcher
lid and use the tamper to
dislodge the ingredients.
When finished, replace the
lid and continue blending.
if the ingredients continue
to stick, consider adding a
little more liquid.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
WARNING: Blades are sharp. Never
insert your hands into the pitcher.
8
9
11
10

14
Handle the easy-twist extractor
blade assembly with care, as
the blades are sharp.
Never leave the appliance
unattended while in use.
NEVER BLEND HOT
INGREDIENTS,as doing
so may cause excessive
pressure buildup, resulting in
risk of personal injury and or
property damage.
nutribullet®cup
assembly & use.
WARNING!
Plug the power cord into
an electrical outlet and
press POWER to turn on
the blender.
5
Add ingredients and liquid
to the nutribullet®cup.
NOTE: Always add liquid. Do not
overfill! To avoid leakage, do not add
ingredients beyond the MAX line.
3
4
Twist the easy-twist
extractor blade onto the
cup until tightly sealed.
1Review all warning and
caution statements in the
Important Safeguards
section (pg 2-5) before
proceeding to Step 2.
2Place the motor base on
a clean, dry, level surface
such as a counter or table.
6
Turn the cup upside down
and place it onto the motor
base, gently turning the
cup clockwise to lock into
the motor base.

7
8
10
To start blending, select
a speed or the EXTRACT
program on the blending
control panel. This program
will turn o automatically.
Buttons will illuminate while
in use.
NOTE: Proceed to the blending
control panel chart on page 16 for
speed definitions.
When you have reached
your desired consistency,
pause/stop the appliance
by pressing POWER or the
speed you selected and wait
for the blades to stop turning.
The unit will enter idle-mode.
The POWER button will
remain illuminated.
NOTE: speeds will automatically
shut o after 60 seconds.
Unlock the assembly by
gently twisting the cup
counterclockwise. You will
hear a click. Enjoy!
NOTE: Blending should not require
longer than one minute to yield
smooth and creamy results.
Press POWER to turn o
the unit completely.
9
CAUTION
Do not remove the easy-twist
extractor blade from the
nutribullet®cup until blending has
completely ceased. Do not use
the easy-twist extractor blade
as a storage lid for your cup.
Some foods may contain active
ingredients or release gases that
will expand if left in a sealed
container, resulting in excessive
pressure buildup that can pose
a risk of injury. When storing
contents in the cup, use plastic
wrap or foil to seal your container.
Always point contents away from
your body when unsealing.
15

16
Blending control panel.
TURNING ON/OFF
The power button actuates
the master power of the
appliance. When pressed, this
button lights up to indicate the
motor is powered on, and the
other functions can be used.
Always turn the master power
o and unplug the unit when
the machine is not in use.
LOW SPEED
Use to mix thin batter,
gravies, marinades; scramble
eggs; process cooked foods
and uncooked fruits.
THE EXTRACT PROGRAM
Use to break down whole
fruits, vegetables, and ice into
nutrient-rich smoothies. This
button will activate a run cycle
that shuts o automatically.
MEDIUM SPEED
Use to cream soups, mix
dips, grind nuts, and
blend sauces, spreads,
mixed drinks, powdered
drinks, and milkshakes.

17
WARNING!
NEVER BLEND HOT INGREDIENTS IN ANY SEALED NUTRIBULLET®CUP
Doing so may cause excessive pressure buildup, resulting in risk of personal
injury or property damage. Hot items should only be blended in the pitcher
using proper safeguards.
HIGH SPEED
Use to liquefy thick
mixtures and blend frozen
fruits and vegetables.
PULSE*
Use to control chopping
and processing.
WARNING: DO NOT
use this setting with
hot ingredients!
How to use the blending control panel.
LOW, MEDIUM OR HIGH
Select a speed and press once
to turn on. The button will
illuminate. To pause/stop the
unit, press the button a second
time — it will de-illuminate — or
press POWER . While in the
idle-mode, the POWER button
will remain lit. To fully power
down after pausing, press
POWER and unplug the unit.
NOTE: If using the pitcher, speeds
will run until paused/stopped. If using
the nutribullet®cups, speeds will
automatically shut o after 60 seconds.
THE EXTRACT PROGRAM
Press the EXTRACT button
and the nutribullet®Blender
Combo will do the work for you.
This program automatically
stops at the end of its cycle. To
pause or stop the blender, press
EXTRACT again or POWER .
PULSE
Press and release the PULSE
button to chop ingredients. If
you hold this button down, it will
continue to run until you release it.

18
Care & maintenance.
MOTOR BASE:
• To avoid risk of injury, NEVER
attempt to clean the actuator
system on the motor base
while the nutribullet®Blender
Combo is plugged in.
• Do not attempt to remove any
pieces from the motor base.
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the
motor base until clean.
• If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
• To clean leakage residue
from the motor base, wipe
with a damp sponge and
warm water.
• If necessary, you may use
a small brush to scrub the
actuator system area to
ensure it’s clean.
WARNING: Never submerge
the motor base in water.
Here’s how to clean
the nutribullet®:
STEP 1:
The most important thing —
ALWAYS POWER OFF THE UNIT
and UNPLUG the motor base
from the power outlet when it
is not in use. Do not attempt to
handle the appliance until all
parts have stopped moving!
This includes during assembly
and disassembly, while
changing accessories during
cleaning, and any time you
leave the machine unattended.
STEP 2:
Detach the nutribullet®cup /
easy-twist extractor blade or
pitcher from the motor base.
STEP 3:
Clean the individual
components (motor base,
easy-twist extractor blade,
nutribullet®cups) as
recommended in the
following pages.
Cleaning the nutribullet®is easy. The pitcher is dishwasher-safe while
the cups and to-go lids are TOP RACK dishwasher-safe. The easy-
twist extractor blade and motor base can be quickly hand-washed
with soap and water. Read on for best practices.

19
NUTRIBULLET®CUPS
& TOGO LIDS:
These items are TOP RACK
dishwasher-safe. We
recommend rinsing and briefly
scrubbing them with a dish
brush to remove any remaining
debris before placing in the
dishwasher. NEVER use the
sanitize cycle to wash the cups
— heat this high can warp
the plastic.
NUTRIBULLET®PITCHER:
WARNING: Blades are sharp!
Use caution when cleaning
the pitcher.
• The pitcher is dishwasher-
safe. We recommend rinsing
and briefly scrubbing it with
a dish brush to remove any
remaining debris before
placing in the dishwasher.
NEVER use the sanitize cycle
to wash the pitcher — heat
this high can warp the plastic.
• If preferred, hand-wash the
pitcher with soap and water.
Stuck-on ingredients might
require extra scrubbing from
a dish brush or sponge.
• Regularly check the
structure of the pitcher and
twisting threads for cracking,
crazing, or breakage.
EASYTWIST
EXTRACTOR BLADE:
• Blades are sharp! Handle
the easy-twist extractor
blade with care when
cleaning! It is best to clean
blades immediately after use
to reduce buildup of residue.
If food particles get stuck,
use a small brush or sponge
to target and dislodge them.
• Do not remove any
components of the easy-
twist extractor blade; this
can result in permanent
damage to the blade,
resulting in leakage when
blending. If, over time, the
easy-twist extractor blade
becomes loose or damaged,
you may order a new easy-
twist extractor blade at:
www.bulletbrands.com.au /
www.bulletbrands.co.nz or
contact customer service.
• Dry the easy-twist extractor
blade completely after
every use.
• Regularly check the
condition of the bottom
of the blade for cracking
or breakage. If damaged,
replace easy-twist extractor
blade immediately to prevent
possible personal injury.
• Do not wash blade
attachments in a dishwasher.

20
If damaged, replace
immediately to prevent
possible personal injury.
• NEVER USE A PITCHER
THAT DOES NOT PROPERLY
ALIGN WITH THE BLADE.
Doing so may cause the
pitcher and motor base to
separate, exposing the
blade assembly and
potentially causing severe
personal injury.
TAMPER
• Always hand-wash the
tamper with soap and water.
Stuck-on ingredients might
require extra scrubbing from
a dish brush or sponge.
STUBBORN CLEAN UP:
If ingredients get stuck to the
nutribullet®cups, easy-twist
extractor blades, or pitcher,
here’s an easy cleanup solution:
fill the vessel with room
temperature (21°C/70°F or less)
water to its MAX line and add
1-2 drops of dish soap. For cups,
twist on the easy-twist extractor
blade, and blend on the motor
base for 20-30 seconds. For the
pitcher, attach lid and blend on
the motor base for the same
amount of time, 20-30 seconds.
This should loosen debris
enough to scrub away with
soap and water.
Your stainless steel straw
should be rinsed with warm
water immediately after use
to ensure food and drink
particles don’t get lodged on
the internal walls of the straw.
For stubborn ingredients, straw
cleaning brushes are available
for purchase from your local
chemist or supermarket.
How to store:
Store the nutribullet® Blender
Combo pitcher upright with the
pitcher lid secured on top. Do
not place anything on top of
the pitcher lid. Store remaining
pieces in a safe place where
they will not be damaged and
won’t cause harm.
WARNING: NEVER store the easy-
twist extractor blade on the motor
base without a nutribullet®cup or
the pitcher as the exposed blades
pose a serious laceration hazard.
Replacement parts.
To order additional parts and accessories, please visit our website
at bulletbrands.com.au / bulletbrands.co.nz.