NUTRIBULLET GO User manual

User guide.

21
PERSONAL SAFETY
NEVER OPERATE THE UNIT
WITHOUT FIRST ATTACHING
THE CUP.
NEVER PUT HOT LIQUIDS IN
THE BLENDING VESSEL. Use
cool or room-temperature
ingredients. Heated ingredients
can create internal pressure in
a sealed blending vessel, which
may erupt upon opening and
cause thermal injury.
WARNING: Friction from the
rotating blade can cause
ingredients to heat and
generate internal pressure
in the sealed vessel. DO NOT
continuously operate the
machine FOR MORE than
ONE MINUTE. If the vessel
feels warm to the touch after
blending, allow it to cool before
attempting to detach the blade.
Once the temperature has
decreased, slowly and
Important safeguards.
WHEN OPERATING YOUR NUTRIBULLET® GO, REMEMBER:
SAFETY ALWAYS COMES FIRST
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your NutriBullet® GO. When using
any electrical appliance, basic safety precautions should always
be observed, including the following important information.
Save these instructions!
FOR HOUSEHOLD USE ONLY
carefully untwist the blade with
the opening pointed away from
your body.
NEVER blend carbonated
beverages. Built-up pressure
from released gases can cause
container to burst, resulting in
possible injury. Always make
sure the cup is securely locked
in place on the base before
blending. The motor will not
turn on unless the cup is fully
locked in place. Do not attempt
to remove the cup while the
unit is in operation.
NEVER permit any blended
mixture to sit inside a sealed
vessel without first releasing
internal pressure. Sugars in fruit
and vegetable ingredients can
ferment, releasing gases that
cause pressure to build within
the vessel. When this happens,
ingredients may burst out of the
vessel when agitated by moving
or opening.
!
To protect against fire, electrical
shock and injury to persons, DO
NOT immerse the motor base
or cable in water or any other
liquid.
BLADES ARE SHARP. Handle
carefully and ALWAYS cover the
blades with the Cup or Blade
Cap when not in use.
DO NOT place hand or fingers
inside the cup when attaching
cup to base unit, and always
keep hands and fingers away
from the blade assembly.
The NutriBullet®GO has sharp
blades and moving parts
and is NOT intended for use
by children or persons with
reduced physical, sensory, or
mental capabilities, or who lack
of experience and knowledge of
its safe operation. Such persons
require close supervision and
thorough instruction on its
proper use and safe operation.
Close supervision is necessary
when any appliance is used
by or near children. Children
should be supervised to ensure
that they do not play with the
appliance.
Turn o power when the
appliance is not in use, before
putting the cup on the base
or taking it o the base, and
before cleaning.
Always make sure the unit
is properly and completely
assembled before turning on
the power and operating the
appliance.
Blades may stop turning during
usage if the cup is overfilled. If
this occurs, completely turn o
the unit by pressing the power
button. Ensure that all moving
parts have come to a complete
stop, then invert the cup/blade/
base assembly, detach the cup
from the base, and remove
excess food from the cup. Ensure
remaining ingredients do not
exceed the MAX Fill Line before
reattaching the cup to the power
base and resuming blending.
Do not leave the appliance
unattended when in use.
Do not incinerate this appliance
even if it is severely damaged.
The lithium-ion batteries can
explodeina fire.Alwaysproperly
recycle products powered by
lithium-ion batteries.
To eliminate any potential
choking hazard for young
children, remove and safely
discard any protective coverings
orplastic bags that the appliance
or its parts may come in.
Ensure that the areas
immediately under or next to
the appliance are clean and
dry before operating. Do not
operate when wet.
Do not use this appliance
for anything other than its
intended use. Do not attempt
to blend anything other than
cool food or liquids intended
for consumption. Misuse may
cause injury.
Do not use this appliance if any
parts appear to be damaged.
READ ALL INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE
OPERATING.

43
PRODUCT SAFETY
DO NOT put any non-food items
into the cup for the purpose of
blending.
This appliance is NOT designed
to be used with ice or frozen
items. Do not use with frozen
fruits or vegetables.
Make sure the unit is turned o
after each use. Ensure power is
o (no light is on), the motor has
stopped, and the blades have
completely stopped moving
before taking o cup or storing
unit.
DO NOT let the USB cable touch
hot surfaces or any extreme
heat source, or become knotted,
tangled, or frayed.
DO NOT modify the charging
cord in any way. Do not use
cord if it shows signs of fraying
or other damage.
Regularly inspect the charging
cable and the appliance for any
damage.
Do not operate appliance with
a damaged cable, or if the
appliance malfunctions or is
dropped or damaged in any
manner. Contact Customer
Service for further assistance.
The use of attachments not
recommended or sold by the
manufacturer may cause fire,
electric shock, or injury, and will
void the limited warranty.
Do not exceed the MAX Fill line
with solid or liquid ingredients
before blending. Doing so can
result in leakage.
Any significant spillage onto the
surface under or around the
appliance, oronto the appliance
itself, should be cleaned and
dried before continuing to use
the appliance.
Remove rinds and peels of
fruit and vegetable ingredients
before blending.
Do not blend stone fruit in this
appliance unless pits/seeds
have been removed.
Keep the appliance clean. Refer
to the Care and Maintenance
section for tips and best
practices.
Do not attempt to repair or
service this appliance. Contact
customer service for further
assistance.
If any of the contained
instructions or warnings are
not understood, please contact
Customer Service for further
assistance.
Save these
instructions!
!
Contents.
05 What’s included
06 Assembly guide
07 Using NutriBullet® GO
09 LED light indications
10 Recipes
13 Care & maintenance
13 How to clean the NutriBullet® GO
13 Replacement parts
15 NutriBullet® GO
one-year limited warranty
Thank you for purchasing the NutriBullet® GO

65
Assembly guide.
NutriBullet®GO cup
blade assembly
motor base
LED status light
power button
USB charging slot
Product configurations may vary. To see our full list of NutriBullet® GO
accessories please visit bulletbrands.com.au / bulletbrands.co.nz
What’s included.
Before you blend: prep steps.
motor base/
blade assembly
NutriBullet®GO
385mL cup
USB type-c
cable
cup cover
blade cover
• CLEAN UNIT (see Care and Maintenance section).
• CHARGE UNIT by plugging the smaller end of the included USB cable into the
slot right below the Power Button (on the front of the base), and the larger end
of the cable into any powered USB slot (in a USB plug adapter plugged into a
power outlet, or on a computer, etc.).
• We recommend fully charging the unit before using it for the first time.
It should take under 3 hours to fully charge.
• A RED LIGHT indicates the unit is charging.
• A BLUE LIGHT indicates the battery is fully charged

8
Using the
NutriBullet®GO.
CAUTION. Never put
hot liquids in the
blending vessel.
NOTE: ALWAYS make sure
that the unit is powered o
and the blades have come
to a complete stop before
separating the cup from
the base.
1Add ingredients into
the NutriBullet cup (but
do not exceed the MAX
line = 300 ml is ~10 fluid
ounces). Always leave
a little room at the
top of the cup for best
blending results.
NOTE: The power button
will only glow blue when
the base and cup are
fastened and locked in
place. If the power button
is not illuminated, or if it
flashes red and blue*,
keep twisting the cup
onto the blade until
properly secured.
4Press the power button
TWICE in quick succession
to start the motor and
begin blending. The BLUE
LIGHT will stay illuminated
throughout the duration
of operation. If you do not
activate blending during
the time the blue light is
flashing, the blender will
return to sleep mode and
you must press and hold
the power button for 3
seconds to wake the unit
out of sleep mode.
5Stop blending by pressing
the power button ONCE.
The blue LED light will turn
o when the motor has
powered o.
NOTE: This unit will
automatically stop
blending after 30 seconds.
Do not operate unit for
more than two consecutive
cycles or continuously for
more than 1 minute.
6 Once you have finished
blending, flip the unit
upside-down and twist
the base anti-clockwise
to remove it from the cup.
7 When not in use, screw the
blade cover onto the base.
2Holding the base from the
bottom, flip it upside-down
and lower onto the rim
of the cup. Twist the base
clockwise to firmly fasten
it onto the cup. Press and
hold the power button for
3 seconds. The BLUE LIGHT
on the power button will
flash for 30 seconds to
indicate that the base and
cup are locked, secure, and
ready for blending.
NOTE: THE CUP MUST BE
LOCKED, OR THE MOTOR
WILL NOT RUN
3With the cup locked firmly
in place on the base, slowly
turn over the blender so
the base can be placed
on a dry, level surface
for blending.
7

109
LED Light Indications.
During operation of your NutriBullet® GO, you will notice LED lights
glowing BLUE or RED at various points of operation. Here is what these
lights indicate. (NOTE: a lack of illumination indicates that the unit is
completely powered o; the motor is not in operation and the blades
have come to a complete stop).
RED LIGHT IS ILLUMINATED
BLUE LIGHT IS ILLUMINATED
FLASHING RED AND
BLUE LIGHTS
FLASHING BLUE LIGHT
BLUE LED REMAINS
ILLUMINATED AFTER DOUBLE
CLICKING POWER BUTTON
FLASHING BLUE LIGHT
AFTER BLENDING
RED LED FLASHES 10 TIMES
RED LED FLASHES
FOR 30 SECONDS
RED LED FLASHES 5 TIMES
UNIT PLUGGED IN,
BATTERY IS CHARGING
UNIT PLUGGED IN, BATTERY
FULLY CHARGED
CUP IS NOT FULLY LOCKED
INTO THE BASE
CUP IS LOCKED IN PLACE
ON BASE, AND BLENDER
IS READY TO USE
BLENDER IS IN ACTIVE USE
AND RUNNING NORMALLY,
LAST 30 SECONDS
UNIT IS DONE BLENDING
BLADES ARE BLOCKED
BY FOOD
LOW BATTERY, NEEDS
TO BE CHARGES
UNIT IS OVERHEATING,
NEEDS TO COOL DOWN
BEFORE RUNNING AGAIN
LED STATUS INDICATES
Recipes.
Creamy strawberry
banana smoothie.
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.
⁄ CUP
1 TBSP
3 SMALL
⁄ SMALL
2 TBSP
UNSWEETENED
ALMOND COCONUT
BLEND MILK OR
MILK OF CHOICE
GREEK YOGURT
SMALL
STRAWBERRIES,
QUARTERED
BANANA, SLICED
VANILLA PROTEIN
POWDER

1211
Blueberry vanilla smoothie.
⁄ CUP
⁄ CUP
2 TBSP
UNSWEETENED
ALMOND COCONUT
BLEND MILK OR
MILK OF CHOICE
BLUEBERRIES
VANILLA PROTEIN
POWDER
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.
Chocolate banana
protein smoothie.
⁄ CUP
1
1 TBSP
2 ⁄ TBSP
UNSWEETENED
VANILLA ALMOND
MILK OR CHOICE
ALTERNATIVE
BANANA, SLICED
PEANUT BUTTER
CHOCOLATE
PROTEIN POWDER
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.
Citrus berry.
⁄ CUP
⁄ SMALL
⁄ CUP
FRESH GRAPEFRUIT
JUICE
LEMONJUICE
ONLY
BLUEBERRIES
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.
Protein-packed kiwi smoothie.
⁄ CUP
1 SMALL
2 ⁄ TBSP
COCONUT WATER
SOFT KIWI,
QUARTERED
CHOCOLATE
PROTEIN POWDER
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.
Matcha smoothie.
⁄ CUP
⁄ SMALL
1 TBSP
UNSWEETENED
VANILLA ALMOND
MILK OR CHOICE
ALTERNATIVE
AVOCADO,
QUARTERED
MATCHA POWDER
Add all ingredients in the
order listed and blend for the
automatic 30-second cycle.
If necessary, repeat the cycle
for one more round to yield a
smoother consistency.

1413
Care & maintenance.
WARNING
Always be extremely careful not
to touch the blades, as these are
very sharp.
WARNING
DO NOT PUT HOT LIQUIDS
IN THE BLENDING VESSEL
WARNING
NEVER SUBMERGE MOTOR
BASE INTO WATER OR ANY
OTHER LIQUID
STEP 3:
When not in use, store all parts
of the blender together in a safe
place where they will not be
damaged and won’t cause harm.
Replacement parts.
To order additional parts and
accessories, please visit our
website at bulletbrands.com.au /
bulletbrands.co.nz
Here’s how to clean
the NutriBullet®:
STEP 1:
Always make sure the
NutriBullet®GO is turned
o after each use.
STEP 2:
Simply place the cup and lid on
the top rack of the dishwasher
or hand wash with warm, soapy
water and rinse. Gently rinse the
blade assembly and carefully
clean with a damp sponge
or cloth.
NOTE: DO NOT fully submerge
the motor base or directly run
under water.
The NutriBullet®GO blade
assembly is NOT dishwasher safe.
Cleaning and caring for your
NutriBullet®GO is as simple as
using it. Here are some tips and
best practices that will keep your
machine in top shape.

1615
If your product becomes
defective due to faulty
material or workmanship
within a period of 1
year from the date of
purchase, we warrant
to do the following:
• For New Zealand Consumers:
We will replace the product
with a new product, free of
charge, or repair the product
at our cost, at our discretion.
• For Australian Consumers:
Our goods come with
guarantees that cannot
be excluded under the
Australian Consumer
Law. You are entitled to
a replacement or refund
for a major failure and for
compensation for any other
reasonably foreseeable
loss or damage. You are
also entitled to have the
goods repaired or replaced
if the goods fail to be of
acceptable quality and the
failure does not amount to
a major failure.
one (1) year limited
replacement warranty
statement.
YOUR WARRANTY
IS SUBJECT TO THE
FOLLOWING CONDITIONS:
• DO NOT operate the
appliance with a damaged
plug or cord, or if the unit has
been dropped, damaged or
dropped in water. To avoid
the risk of electric shock, do
not disassemble or attempt
to repair the appliance
on your own. If the supply
cord is damaged, it must
be replaced by a qualified
electrician in order to avoid
a hazard. Incorrect re-
assembly or repair can
cause a risk of electric shock
or injury to persons when the
appliance is used.
• The item has not been
misused, abused, neglected,
altered, modified or repaired
by anyone.
• The item has been subjected
to fair wear and tear.
• The item has not been used
for trade, professional or
hire purposes.
• The item has not sustained
damage through foreign
objects, substances or accident.
YOUR WARRANTY
DOES NOT COVER:
• Components that are
subject to natural wear
and tear caused by
normal use in accordance
with operating instructions.
• Unauthorised/improper
maintenance/handling or
overload is excluded from
this warranty.
• For guarantee claims, you
will need to submit a proof
of purchase in the form of
a valid receipt that displays
date and place of purchase.
This warranty does not replace
but is in addition to your
statutory rights.
This warranty does not apply
to accessories supplied with
the item.
This warranty applies only to
the original purchaser and
may not be transferred.
Replacement items will
be covered by the limited
warranty for the balance of the
warranty period from the date
of the original purchase.
PLEASE NOTE:
Only the defective product
or parts returned to place of
purchase will be replaced
under this warranty.
NEW ZEALAND
PO Box 100-707
NSMC
Auckland 0745
0800 285538
www.bulletbrands.co.nz
AUSTRALIA
PO Box 574
South Morang
Victoria 3752
1300 285538
www.bulletbrands.com.au
NutriBullet is a registered trademark of CapBran Holdings, LLC.
Copyright © 2020 CapBran Holdings, LLC. All rights reserved.
Los Angeles, CA 90025, USA. Made in China.

1817

bulletbrands.com.au / bulletbrands.co.nz
MODEL: (NBG-100) NB07300
RATING: 7.4V
USB INPUT FOR CHARGE: 5V 2A 10W
Capital Brands Distribution, LLC, Los Angeles, CA 90025
nutribulletgo.com | All rights reserved.
NutriBullet® and the NutriBullet® logo are trademarks of
CapBran Holdings, LLC registered in the U.S.A. and worldwide.
Illustrations may dier from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein
are subject to change without notice.
200916