NUTRIBULLET BALANCE User manual

USER GUIDE
®

FOR YOUR SAFETY, CAREFULLY READ ALL INSTRUCTIONS
BEFORE OPERATING YOUR NUTRIBULLET BALANCE®.
IMPORTANT SAFEGUARDS &
CAUTIONARY INFORMATION • DO NOT USE THE NUTRIBULLET BALANCE®WITH ANY TYPE OF
ADAPTOR OR VOLTAGE CONVERTER DEVICE.
• USE OF ADAPTERS AND CONVERTERS IS CONSIDERED AN
UNAUTHORIZED MODIFICATION OF THE NUTRIBULLET
BALANCE®AND AS SUCH WILL VOID THE WARRANTY. USE
OF THE NUTRIBULLET BALANCE®IN AREAS WITH DIFFERENT
ELECTRICAL SPECIFICATIONS MAY RESULT IN DAMAGE TO IT.
• UNPLUG THE NUTRIBULLET BALANCE®WHEN IT IS NOT IN
USE. MAKE SURE THE POWER BASE IS UNPLUGGED BEFORE
ASSEMBLING, DISASSEMBLING, ADDING ADDITIONAL PARTS,
OR CLEANING.
• Do not pull, twist, or damage the power cord.
• Do not allow the power cord to hang over the side of the counter
or table.
• Do not allow the power cord to touch hot surfaces, including stove.
• Periodically inspect the power cord and plug for signs of damage.
Never operate any appliance with a damaged power cord or plug.
Electrical Safety
When using any electrical appliance, basic safety precautions
should always be observed, including the following:
• Caution! To avoid risk of electric shock, never immerse the
power cord, plug, or power base of blender in water or other
liquids.
• THE USE OF ATTACHMENTS, INCLUDING CANNING JARS,
NOT RECOMMENDED OR SOLD BY THE MANUFACTURER
MAY CAUSE FIRE, ELECTRIC SHOCK, OR INJURY AND VOID
THE WARRANTY.

If the NutriBullet Balance®malfunctions or is dropped, or damaged
in any manner, discontinue use and contact Customer Service for
further assistance.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• Always disconnect the appliance from the supply if it is left
unattended and before assembling, disassembling or cleaning.
• Switch o the appliance and disconnect from power supply before
changing accessories or handling moving parts.
• At all times, avoid contact with moving parts.
• Keep hands and utensils away from the cutting blade while chopping
or blending food to reduce the risk of severe personal injury or
damage to the device. A scraper may be used, but only when the
blender/food chopper is not running and the NutriBullet Balance®is
unplugged.
• Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved.
• NEVER LEAVE THE NUTRIBULLET BALANCE®UNATTENDED
WHILE IT IS IN USE.
• This appliance shall not be used by children. Keep the appliance
and its cord out of reach of children.
• Children shall not play with the appliance.
 TO PREVENT OVERHEATING, NEVER ALLOW THE MOTOR TO
RUN FOR MORE THAN ONE MINUTE AT A TIME, AS IT CAN
CAUSE PERMANENT DAMAGE TO THE MOTOR IF THE
MOTOR STOPS WORKING, UNPLUG THE POWER BASE AND
LET IT COOL FOR AN HOUR BEFORE ATTEMPTING TO USE
IT AGAIN YOUR NUTRIBULLET BALANCE®HAS AN INTERNAL
THERMAL BREAKER THAT SHUTS OFF THE UNIT WHEN IT
OVERHEATS THE POWER BASE WILL RESET WHEN THE UNIT
IS UNPLUGGED AND THE THERMAL BREAKER COOLS DOWN

• To reduce the risk of injury and leakage, make sure the blade
base is securely screwed onto the cup before placing it on the
Power Base and operating the NutriBullet Balance®.
• Do not use NutriBullet Balance®outdoors. Do not allow the
NutriBullet Balance®to be exposed to inclement weather
elements such as rain or other wet conditions.
 NEVER PUT YOUR HANDS OR UTENSILS NEAR THE MOVING
BLADE and never use your hands or utensils to press the activator
buttons down while the NutriBullet Balance
®
is plugged in.
 BLADES ARE SHARP USE CARE WHILE HANDLING THE BLADES
AND DO NOT TOUCH THE BLADE EDGES TO AVOID INJURY
 NEVER INSERT THE BLADE INTO THE POWER BASE WITHOUT
FIRST ATTACHING THE CUP
 WE RECOMMEND REPLACING YOUR EXTRACTOR
BLADE EVERY 6 MONTHS OR AS NEEDED FOR OPTIMAL
PERFORMANCE
 PERIODICALLY INSPECT ALL NUTRIBULLET BALANCE®
COMPONENTS FOR DAMAGE OR WEAR THAT MAY IMPAIR
PROPER FUNCTION DISCONTINUE USE AND REPLACE CUPS
IF YOU DETECT CRACKING, CRAZING, OR CLOUDINESS OR
DAMAGE TO THE PLASTIC OR ANY ACTUATOR
• Check gasket to make sure it is completely seated in the cross
blade before each use.
• The NutriBullet Balance®is not intended for use in microwave
ovens. Do not place the NutriBullet Balance®cups, power base
or any accessories in a microwave as this may result in damage
to its various parts.
• To reduce the risk of personal injury or damage to the device,
keep hands and utensils away from the cutting blade.
• Never blend carbonated beverages. Built-up pressure from
released gases can cause the sealed cup to burst, resulting in
possible injury.
• To prevent leakage when creating a recipe, ALWAYS make
sure that the ingredients do not extend above the MAX line.

 DO NOT PUT HOT LIQUIDS OR INGREDIENTS IN ANY
BLENDING VESSEL BEFORE BLENDING START WITH COOL OR
ROOM TEMPERATURE INGREDIENTS HEATED INGREDIENTS
CAN CREATE INTERNAL PRESSURE IN A SEALED BLENDING
VESSEL, WHICH MAY ERUPT ON OPENING AND CAUSE
THERMAL INJURY
• NEVER put hot liquids or ingredients in any blending vessel as it
can be ejected out of the appliance.
• CAUTION! Friction from the rotating blade can cause
ingredients to heat and generate internal pressure in the
sealed vessel. Do not continuously operate for more than one
minute. If the vessel is warm to touch, allow it to cool before
carefully opening it pointed away from your body.
• Extract for no longer than 1 minute. If more extraction is needed,
wait 1 minute, then repeat the extraction process in 1 minute
intervals up to three times as needed to achieve the desired
consistency. If more than three 1-minute extractions are needed,
allow the Power Base to cool for 2-3 minutes after the third
extraction before beginning the next round.
• Never permit any blended mixture to sit inside a sealed vessel
without first releasing internal pressure.
• Do not allow blended mixtures to sit for long periods of time in
a sealed container. The sugars in the fruit and vegetables can
ferment, creating gas and causing pressure to build up and
expand in the vessel which can cause ingredients to burst and
spray out when moved or opened.
• Never use the NutriBullet Balance®to blend ingredients without
adding liquid in as doing so may damage the blade.
• The cyclonic action of your NutriBullet Balance®requires the use
of liquids to make NutriBlasts and other nutritious beverages. The
NutriBullet Balance®is not intended to be used as an ice crusher,
and not without liquids. To make a delicious cold NutriBlast, we
suggest that you use frozen fruit and chilled liquids. Alternatively,
you may add crushed ice, up to 25% of the total cup volume, with
water or other liquid filled up to the “MAX” line. Do not crush ice or

other hard items without liquid, as such prolonged use over time
may dull or damage the blades. Always inspect your blades before
each use.
• To stop the motor, twist the cup to release it from the lock mode,
and at the same time, press the cup/blade assembly down and wait
for the motor to power down completely.
• Never remove the cup and blade assembly from the power base
until the motor comes to a complete stop. Removing the cup/
blade assembly while the power base is still running may cause
damage to the blade coupling or motor gear.
• The Smart Nutrition Sensor™ includes a delicately calibrated
scale. Handle with care. If it is dropped or jarred, it may impact
the calibration causing it not to connect or detect the placement
of the cup. If this occurs, please contact customer server for
assistance.
WARNING: VENTILATION CAUTION
• Always operate the NutriBullet Balance®on a level surface,
leaving unobstructed space beneath and around the power
base to permit proper air circulation. Slots and openings on the
bottom of the NutriBullet Balance®are provided for ventilation
to ensure reliable motor operation and to prevent over-heating.
WARNING!
•To prevent fire hazard, power base openings should be free of
dust or lint and never obstructed with flammable materials such
as newspapers, tablecloths, napkins, dish towels, or place mats.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY

WARNING!
• IF YOU ARE TAKING ANY MEDICATION, ESPECIALLY
CHOLESTEROL-LOWERING MEDICATION, BLOOD
THINNERS, BLOOD PRESSURE DRUGS, TRANQUILLIZERS, OR
ANTIDEPRESSANTS, PLEASE CHECK WITH YOUR DOCTOR
BEFORE CONSUMING ANY OF THE NUTRIBLAST RECIPES.
• THE FOLLOWING LIST OF SEEDS AND PITS CONTAIN
CHEMICALS THAT RELEASE CYANIDE INTO THE BODY WHEN
INGESTED. DO NOT USE THE FOLLOWING SEEDS AND PITS IN
THE NUTRIBULLET BALANCE®: APPLE SEEDS, APRICOT SEEDS,
CHERRY PITS, PLUM PITS, AND PEACH PITS.
Cleaning Safeguards
• RINSE BLADES (AND CUPS) IMMEDIATELY AFTER USE TO
PREVENT DEBRIS FROM DRYING AND STICKING TO VESSELS
— IF NECESSARY, USE A DISH BRUSH TO LOOSEN ANY
DEBRIS.
• HAND WASH ONLY WITH MILD DISH SOAP AND ROOM
TEMPERATURE WATER (NOT HOT).
• DRY IMMEDIATELY.
• FOR TOUGH DEBRIS, FILL THE CUP ½ FULL WITH ROOM
TEMPERATURE (NOT HOT), MILD SOAPY WATER. THEN, SIMPLY
TWIST ON THE BLADE, POP IT ON THE BASE AND GIVE IT A RUN
FOR 30-45 SECONDS. FOLLOW UP WITH A QUICK BRUSH.
• DO NOT PUT THE BLADES IN THE DISHWASHER AS ELEVATED
TEMPERATURES CAN DAMAGE GASKETS. SIMPLY HAND WASH
WITH WARM, MILD SOAPY WATER.
• THE NUTRIBULLET BALANCE®CUPS CAN BE WASHED ON THE
TOP RACK OF THE DISHWASHER USING THE NORMAL (NOT
SANITIZE) CYCLE. THE NUTRIBULLET BALANCE®CUPS AND
BLADES SHOULD NOT BE IMMERSED IN BOILING WATER FOR
ANY REASON AS THIS WILL WARP THE PLASTIC AND DAMAGE
THE GASKET.
• WHEN WASHING BLADES, DO NOT ATTEMPT TO REMOVE THE

GASKET RING. SIMPLY HAND WASH THE BLADES IN WARM,
MILD SOAPY WATER. ATTEMPTED REMOVAL OF THE GASKET
MAY PERMANENTLY DAMAGE THE BLADE CONFIGURATION
AND CAUSE LEAKAGE.
CLEANING THE NUTRIBULLET BALANCE®
Everyone hates cleaning up, which is just one more reason the
NutriBullet Balance®is such a wonderful time saver.
WARNING:
• ALWAYS UNPLUG THE NUTRIBULLET BALANCE®WHEN
CLEANING OR ASSEMBLING.
Cleaning the NutriBullet Balance®is so easy… simply place any of
the pieces (except for the Power Base, Smart Nutrition Sensor™,
and blades) on the top shelf of the dishwasher or hand wash
with warm soapy water and rinse.
WARNING:
DO NOT WASH THE BLADES IN THE DISHWASHER. THE
NUTRIBULLET BALANCE®CUPS CAN BE WASHED IN THE
DISHWASHER BUT ONLY ON THE TOP RACK USING THE
NORMAL (NOT SANITIZE) CYCLE. THE NUTRIBULLET BALANCE®
CUPS AND BLADES SHOULD NOT BE IMMERSED IN BOILING
WATER FOR ANY REASON AS THIS WILL WARP THE PLASTIC
AND DAMAGE THE GASKETS.
Stubborn Cleanup
If ingredients dry inside the NutriBullet Balance
®
, make your cleanup
a snap by filling the cup about 2/3 full with room temperature soapy
water and screw on the Extractor Blade. Place the cup assembly on
the NutriBullet Balance
®
, power base for about 20-30 seconds. This will
loosen the stuck ingredients, and with a light scrub, you’ll be all done.
14 | nutribullet.co.uk nutribullet.co.uk | 15

arrow on the Disc to the arrow in the well of the power base.
Gently press down until the disc is level.
NEVER SUBMERGE
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
For more how-to information,
visit nutribullet.co.uk
CLEANING THE NUTRIBULLET BALANCE®POWER
BASE & SCALE
For the most part the power base doesn’t really get dirty, but
if you neglect to twist the blade on to the cup tightly, liquids
can leak out and get into the base and activator buttons. If this
happens please use the following cleaning instructions.
Step 1: The most important thing is to UNPLUG the power base
before cleaning!
Step 2: Make sure the blade is not attached to the power base.
Step 3: Remove the Smart Nutrition Sensor™ from the power
base.
Step 4: Wipe the Smart Nutrition Sensor™ with a damp cloth
until clean.
Step 5: Wipe the well in the bottom of the power base with a
damp cloth until clean.
Step 6: Replace the Smart Nutrition Sensor™ by lining up the

21 Introduction
22 Let’s Get Started
24 Connecting with Bluetooth® wireless technology
25 Troubleshooting
Using with Multiple Devices, 25
Connecting and Disconnecting Manually, 26
Disconnecting the Balance Blender, 28
29 Start Making Your Recipes
38 Manual Mode
44 Cleaning the NutriBullet Balance®Smart Nutrition Sensor™ and Well
Table of
Contents

The NutriBullet just got smarter with NutriBullet Balance®! Born from
a quest for blending excellence, NutriBullet Balance®features Smart
Nutrition Sensor™ technology that sends REAL-TIME nutrition data via
Bluetooth® wireless technology to your smart device as you blend recipes.
View carbs, calories, protein, sugar and more in real time! This provides
tighter control over blends by letting you know exactly what you’re making
as you’re making it. Unlike other blenders, with NutriBullet Balance®
nothing is left to chance, you always know exactly what you’re getting!
Watch recipes come to life and tweak them on the fly to suit your taste.
No more sugary treats disguised as healthy smoothies or protein shakes
in name only. With NutriBullet Balance®the smoothie you envision is the
smoothie you can make, down to the gram, every time.
We hope you’ll enjoy the newest member of the NutriBullet family as
much as we do. Say goodbye to measuring cups, eyeballed amounts
and wild card results...with NutriBullet Balance®, the only thing you’ll be
eyeballing is a better YOU!
The Evolution
of Blending
nutribullet.co.uk | 21

Let’s Get Started!
Download the NutriBullet Balance®App from
NutriBulletBalance.com/app
or find it in either:
nutribullet.co.uk | 23

Connecting with Bluetooth®
wireless technology
The NutriBullet Balance®uses Bluetooth®wireless
technology to connect to the Balance App on your
smartphone or tablet.
To connect the NutriBullet Balance®to your device:
1. Make sure your smart device has Bluetooth® wireless
technology turned on.
2. Open the NutriBullet Balance®App.
3. Plug in your NutriBullet Balance®; the button’s blue
light will blink three times and go o.
4. NutriBullet Balance®will connect to the App
automatically, and the blue light will come on.
See the following section if it does not.
Connected
Not Connected
Troubleshooting
Using with Multiple Devices
Your NutriBullet Balance®can only connect to one device at a time.
If you are having trouble connecting, make sure the Balance is not
connected to a dierent device.
If your Balance is still connected to a previously used device, quit the
NutriBullet Balance®App running on that device. The Balance will
disconnect automatically.
*For phone/tablet compatibility, go to makeitperfectly.com/compatibility.
24 | nutribullet.co.uk nutribullet.co.uk | 25

Connecting and
Disconnecting Manually
You can connect to or disconnect
from the NutriBullet Balance®
manually in the Balance App. Touch
the NutriBullet Balance®icon to the
right of the search box to open the
Available Blenders list.
The App will display a check mark
next to the NutriBullet Balance®it
is currently connected to.
Touch a NutriBullet Balance®in the
list to connect to it or disconnect
from it.
nutribullet.co.uk | 27

Disconnecting the
NutriBullet Balance®
You can force the NutriBullet
Balance®to disconnect from
the device it is connected to by
touching and holding the button
on the blender. The light will
turn o.
Start
Making
Your
Recipes
A. Make sure your
NutriBullet Balance®is
connected to the App.
B. In the Search bar, type
in the name of the
recipe or choose from
our recipe categories
to select your recipe.
A
B
nutribullet.co.uk | 2928 | nutribullet.co.uk

C
C. View recipes and
ratings quickly
by using filters.
Select your recipe.
D. Click on the BLEND
button.
When prompted,
remove all items
from the Base.
NOTE: Make sure nothing
is on top of the Smart
Nutrition Sensor™.
D
30 | nutribullet.co.uk nutribullet.co.uk | 31

E. When prompted,
place the Balance
Cup on the Power
Base, open side up.
E
F
F. Follow the step-by-
step directions in
the recipe.
NOTE: To prevent
leakage when creating
a recipe, ALWAYS make
sure that the ingredients
do not extend above
the MAX line.
NOTE: Make sure
the Smart Nutrition
Sensor™ is in place.
32 | nutribullet.co.uk nutribullet.co.uk | 33

G
G. When prompted,
twist the Blade onto
the cup. Flip-over
the cup, place it
onto the base,
then push and
twist to the right.
The NutriBullet
Balance®will start
blending.
H. Wait until the
timer stops.
H
34 | nutribullet.co.uk nutribullet.co.uk | 35

I. Push and twist the
Cup and Blade to
the left to release
them from the
Power Base.
Remove the Blade.
Enjoy!
36 | nutribullet.co.uk nutribullet.co.uk | 37

1 Add ingredients
to the Colossal Cup.
 Add the liquid of
your choice up to
the MAX line. (Liquid is
required! Ingredients
should not exceed the
MAX line!).
To Blend:
NOTE: The NutriBullet Balance
®
Cup requires room to properly
extract and blend the ingredients
completely. Exceeding the MAX
line may result in leakage.
Manual Mode
You can use the NutriBullet Balance®without using the Balance App.
This is called Manual Mode. This mode is used for simply blending.
PLEASE NOTE: you will not get any nutritional information or data in
Manual Mode.
38 | nutribullet.co.uk nutribullet.co.uk | 39