Nuu Garden SCD001-01 User manual

INSTRUCTION MANUAL
3PCS Cast Aluminum Bistro Set

INTRODUCTION
· Only need to rinse it thoroughly with clean water to wash away dirt and
grime. Never use abrasive cleansers on the furniture, since it can attack
the surfaces and leave behind scratch marks.
CUSTOMER SERVICE
1 6
Thanks for purchasing this us furniture. We are here to help you
maximize your enjoyment and appreciation of it.
Please do not hesitate to contact our customer service when you have any
questions regarding assembly or accessories.
Thanks for purchasing and trusting us with your home
decorating plans.
We are committed to R&D innovation and to create the most
rened, diverse choice of outdoor collection.
After unpacking and before every use, check whether the item
shows any damages. In addition, check that you have all parts and
hardwares before assembly. If there is any damage, please do not use
and just call customer service. I f you d o no t have all the parts
lists, have your dealer contact us and they will be sent to you
immediately.
This furniture is intended for indoor and outdoor use. Please take
time to read and follow the instruction below. Use the item as
described in this operating manual.We accept no liability for
damages caused by improper use.
· For the stubborn grime and stains, just use a soft sponge and mild soapy
water and then dry it with a cloth or paper towel. · Check the stability of the
screws, nuts and nut caps prior to each use. If necessary, tighten all of them
again to ensure it is secure.Tighten up them after one
to two month’s use whenever required.
· Place the furniture on an even, sturdy surface.
· Avoid improper use, and be careful not to scratch or damage the surface with
sharp objects.
· When you move your furniture, make sure you lift it rather than pulling
or pushing it to avoid damaging the oor, legs and mounting.

PARTS
DO NOT TIGHTEN BOLTS OR SCREWS UNTIL COMPETELY ASSEMBLED!!
DescriptionPhoto Qty Item Description
A
B
C
G
1
3
QtyPhoto
F
D
H1
6
E J
I
6
3
6
6
3
Item
Bolt(Long)
Nut
Cap
Bolt(Short)
Top Table
Leg
Washer
Spring Washer
Connect
A
B
H
D
F
G
I
E
Step:1 Step:2
Step:3 Step:4
D
F
G
E
Step 1
Contect the seat frame (A) and back frame (B) using 2 bolts (L), 2 washers (M8,
F), 2 nuts (M8, H) and 2 nut caps (M8, N).
Step 2
Assemble legs (C) to seat frame (A) with 8 bolts (K), 8 washers (M8, F),
8 nuts (M8, H) and 8 nut caps (M8, N).
Step 3
Attach the arms (D) to seat frame (A). Secure and tighten from inside
using 2 cross bolts (I), 4 washers (M6, E), 2 nuts (M6, G) and 2 nut caps
(M6, M).
Step 4
Fasten the arms (D) to back frame (B) with 2 cross bolts (J), 4 washers
(M6, E), 2 nuts (M6, G) and 2 nut caps (M6, M).
Step 5
Secure and tighten all the nuts and nut caps before using.
CARE AND MAINTENANCE
With a little care you can prolong the life of your furniture. Follow the
instruction for the materials of your special product to make sure that it stays
in the best shape for as long as possible.
The information below is only intended as a general guideline. For more
information, please enquire where you bought the furniture.
ASSEMBLY INSTRUCTIONS FOR CHAIR
5 2

Step 1
Assemble the legs (B) to top table (A) with 3 bolts (long, H), 3 washers (D), 3
spring washers (E), 3 nuts (F) and 3 nut caps (G).
Step 2
Place 3 bolts (short, I) to legs (B).
Step 3
Fasten the Connect part (C) with 3 bolts (Short, I), 3 washers (D), 3 spring
washers (E), 3 nuts (F) and 3 nut caps (G).
Step 4
Secure and tighten all the nuts and nut caps before using.
ASSEMBLY INSTRUCTIONS FOR TABLE A
C
F
H
N
K
B
E
D
G
I
J
M
L
DescriptionPhoto Qty Item Description
A
B
C
I
1
1
Qty
Washer(M6)
Photo
H
D
J4
2
F
E
G
L
K
M
N
10
4
10
8Bolt(M8*30)
Bolt(M8*40)
Back frame
Seat Frame
Legs
Arms
Cross Bolt
(M6*25)
2
2
8
Washer(M8)
Nuts(M6)
Nuts(M8)
Cross Bolt
(M6*30) 2
Nut Caps(M6)
Nut Caps(M8)
4
10
Item
PARTS
4
3