NUUO SCB-C31A POS User manual

Metadata Plugins
Access Control, License Plate Recognition
and Point of Sale Solutions
Hardware & Software Installation
User Manual
Ver. 99.350.B0430.001

Intelligent Surveillance Solution
Table of Contents
page-1
TABLE OF CONTENTS
TABLE OF CONTENTS ..............................................................................................1
SYSTEM INTRODUCTION .........................................................................................2
Definition of Terms ..........................................................................................2
Product Specification ....................................................................................3
HARDWARE INSTALLATION ....................................................................................4
SCB-C31A POS data capture convertor.....................................................4
SOFTWARE INSTALLATION ......................................................................................6
SCB-C31 POS data capture convertor .......................................................6
Connection via COM Port ............................................................................7
Connection via TCP Client............................................................................7
NUUO NVR/DVR/Hybrid system installation ................................................7
SOFTWARE SETUP ....................................................................................................8
1. Metadata Device Management ............................................................8
1.1. Insert/Delete/Configure Metadata devices ...................................9
1.2. New/Edit/Delete/Import/Export Tag Filter .....................................11
1.3. Setup metadata Display Font..........................................................16
2. Smart Guard Detection ...........................................................................17
2.1. Metadata Event.................................................................................17
2.2. Instant Action on Metadata Event .................................................21
3. Playback ....................................................................................................22
4. Remote Network Service.........................................................................22
OPERATION TOOLS ...............................................................................................24
1. Live Display ................................................................................................24
2. Log Viewer Search ...................................................................................25
3. Metadata transaction data Search......................................................27
4. Playback video with metadata data ...................................................28
5. Backup video with metadata data ......................................................29
6. Remote Access.........................................................................................31

Intelligent Surveillance Solution
System Introduction
page-2
SYSTEM INTRODUCTION
NUUO Metadata plugins enable users to build integrated solutions with 3rd
party devices, currently including Access Control, License Plate
Recognition and Point of Sale Solutions. Please contact your local
distributor or sales service for the latest list of integrated solutions from
various suppliers.
Access Control
NUUO Main Console accepts feeds from Access Control servers via
Ethernet. You may configure several doors or entrances under each
Access Control Source. Filtered info will be displayed on chosen
channels, for example ID numbers or names of personnel upon each
entry or exit.
License Plate Recognition
NUUO Main Console also accepts feeds from License Plate Recognition
Systems via Ethernet. Several lanes may be configured under each LPR
Source. Filtered info will be displayed on chosen channels, including
license plate numbers or other additional information.
Point of Sale
NUUO POS provides a platform to display financial transaction data upon
video surveillance channels. The architecture is as below; POS
transaction data flows to NVR by Ethernet. Each Cash Register with an
external receipt printer is connected by DB9 cable. The transaction
information delivered in R232 format can be converted to Ethernet
through SCB-C31A POS data capture convertor. Alternatively, Cash
Registers that support TCP/IP or COM port output can connect directly to
the system without the SCB-C31A box.
Definition of Terms
Terms
Definition
Metadata Original Data
Original data from Metadata devices. Usually with a
lot of symbols and no line feed.
Metadata Transaction
Filtered result by user defined tag filter.
Metadata Event Log
Smart Guard Event Log from metadata transaction.
Includes transaction start, transaction end, POS cash
register open and other user defined events.
Abbreviation of Metadata Log.

Intelligent Surveillance Solution
System Introduction
page-3
To give you a better idea of the various source types supported by the
Point of Sale solution, the following sections (Hardware Installation and
Software Installation) are dedicated to POS Metadata and the hardware
POS box only. If you are not planning to install this solution, please
proceed directly to page 8 for Software Setup.
POS System Diagram
Product Specification
NUUO Capture Box
SCB-C31A POS
Input
RS232
Output
Ethernet
DC In
DC +10V to +15V
Power consumption
500 mA
Operating Temperature
-20 to 65℃
Operating Humidity
0-90 % Non-Condensing
Baud Rate
110 bps to 230.4 kbps
Data Bits
5, 6, 7 or 8
Stop Bits
1, 1.5 or 2
Parity
None, Even, Odd, Mark, Space
Flow Control
None, RTX/CTS, XON/XOFF, DTR/DSR

Intelligent Surveillance Solution
Hardware Installation
page-4
HARDWARE INSTALLATION
SCB-C31A POS data capture convertor
To connect Cash Register, Printer, and SCB-C31A POS data capture
convertor together, please follow below steps:
Step 1: Please refer the user manual to setup Cash Register and printer.
Step 2: Using a “Y-shape” DB-9 cable, one DB-9 female connect to
POS system and one DB-9 male connect to the receipt printer
Y-shape (provided by Printer vendor).
Step 3: Using another DB-9 female connect to SCB-C31A POS Data
Capture R232/Ethernet convertor with Null modem.
Note: There are two kinds of serial cable: Straight pass-through
and Null-Modem. The connection between SCB C31A POS
Data capture box and Y-cable must be null modem (in
package).
Step 4: Check the system switch of the SCB-C31A POS is switch to OFF,
OFF position.
Step 5: Connect power source with SCB-C31A POS.
Step 6: Connect SCB-C31A POS with internet port by RJ45 LAN cable.
SCB-C31A POS
Cash register
Printer
Null Modem
Y-cable
Ethernet
Provided by printer
F
F
M
M
F

Intelligent Surveillance Solution
System Introduction
page-5
The LED Indicators:
PWR LED: System is ready (Blinking).
LINK LED: Ethernet cable connection and data active.
RXA LED: Transiting/Receiving Indicator.
TXA LED: No option of SCB-C31A POS
Reset
Switch
Power
RS-232
RS-232
RJ-45

Intelligent Surveillance Solution
Software Installation
page-6
SOFTWARE INSTALLATION
SCB-C31 POS data capture convertor
Step 1: Use IE-browser to setup SCB-C31A POS, the default IP address is
192.168.1.1
Step 2: Setup IP address and password, and then setup IP address.
Note: Each time you switch the page of the web, please click
Save at first. If you leave this page without saving, all changes
will be ignored.
Step 3: Setup Password if needed. Password is only using to activate a
security feature on the serial server. Once a password is entered
it will be required to access the menu and make change of
configuration when access.
Note: Please write down the Serial number and MAC address,
these two parameters are necessary when user forget your
password.
Step 4: Setup according to your POS or Cash Register. Usually all
devices are default setting, you can reserve your time to pass
this step.
Step 5: Please restart/reset the box after changing configurations to
active setup.
To reset the unit manually apply power, insert a small plastic

Intelligent Surveillance Solution
System Introduction
page-7
tool, and press lightly depressing reset located between the
switch (refer page 5). Hold for 3 seconds and release. The Link
and Run light will go out and turn back on. The SCB-C31A POS
will revert to the last setting.
Note: Every time you change the configuration of SCB-C31A
POS, please check the above settings, especially maximum
connection and Remote IP address to avoid connection fail.
Connection via COM Port
Please install system according to following diagram:
Connection via TCP Client
Please install system according to following diagram:
NUUO NVR/DVR/Hybrid system installation
Please refer to the Main Console user manual to complete system
installation with the NVR/DVR/Hybrid systems installation CD.

Intelligent Surveillance Solution
System Setup
page-8
SOFTWARE SETUP
1. Metadata Device Management
Each NUUO Main Console system can manage up to 64 Access control,
64 License Plate Recognition and 64 POS cash register devices. This
section will teach you how to setup configuration of your system.
Run Main Console and click on Metadata Application from the
Config menu to open the Metadata Application window.
You are able to Insert/Delete/Configure Metadata devices in this window.
Click on any device under the Metadata Tree to configure the settings
and tag filter of the device. Associated cameras will be shown in the
preview window below.
Metadata
Tree
Associated
Cameras

Intelligent Surveillance Solution
System Setup
page-9
1.1. Insert/Delete/Configure Metadata devices
To insert a metadata source
1. Click the Insert button when the Metadata tab is selected
to open the Metadata Source Setting window.
2. Configure metadata source info, including Name, Metadata Type,
Source Type, IP address and Port.
Note:
For Metadata Type POS, there are 4 source types available
including SCB-C31, SCB-C31_A, COM Port and TCP Client.
3. After setting, click Test Connection to test Metadata source
connection. If all the settings are correct, the system will popup
“Metadata server “name (IP)” is available” message to confirm the
setting is successful.
To insert a metadata channel
1. Click the Insert button when any Metadata Source tab is
selected ( , or ) to add a
metadata channel.
Note:
For Metadata Type Access Control, you may add several metadata
channels under one source. Please define each Door Name exactly
the same as your settings under the third party Access Control system.
For Metadata Type LPR, you may add several metadata channels
under one source. Please define each Lane Name and make sure
settings under the third party LPR system are exactly the same.