Nuvico Xcel NCT-8ML-B21AF User manual

Package
Overview
Installation
1
2
3
4
►Connecting Network Cable
Warning and Caution
■If the product does not work properly, please contact your dealer or
the nearest service center. Never attempt to disassemble the camera
yourself. (We shall not be responsible for any problems caused by
unauthorized repair or maintenance.)
■In the use of the product, you must be in strict compliance with the
electrical safety regulations of the nation and region. When the product is
mounted on wall or ceiling, the device shall be firmly fixed.
■Do not allow water or liquid intrusion into the camera.
Do not use camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
.
■Do not aim the camera at the sun or extra bright place.
■Do not place the camera in extremely hot, cold (the operating
temperature shall be -22˚F~140˚F), dusty or damp locations, and do not
expose it to high electromagnetic radiation.
■To avoid heat accumulation, good ventilation is required for
operating environment.
■
NCT-8ML-B21AF Bullet Camera
Quick Start Guide
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install the camera
under dry environment.
①
the drill template.
Drill the screw holes and the cable hole on the wall according to
Camera Quick start guide
CD Plastic plug × 4
Drill template Rubber plug
4 tapping screws PA 4×25
1 machine screw PWM3×5
■Please read these instructions carefully before operating the unit
and keep it for further reference.
■All the examples and pictures used here are for reference only.
■The contents of this manual are subject to change without notice.
2
13
1 Fixed Ring
2 Mounting Base
3
4
Network connector*
Audio Input
* It is recommended to install the security cap for outdoor installation.
*If the PoE switch is used to power the camera, DC12V power supply is not
required.
Security cap
12
3
4
5
6
7
DC12V
5 Power connector*
6 Micro SD card slot
7 Reset
①Loosen the nut from the main element.
②Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
•Access the camera through Xcel IP Utility
①Make sure that the camera and the PC are well connected via LAN.
②Find the Xcel IP Utility from the CD and then install it in the
computer. After that, run the Xcel IP Utility as shown below.
Device Network Search
Immediate Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.2 26.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Netw ork Parame ter
Mac Address
IP Address
Modify
CE :98 :23 :75 :3 5 :22
192 . 168 . 226 . 201
255 . 255 . 255 . 0
192 . 168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify t he network p arameter s.
Total Device: 3 Local IP Address:192.168.1.4Subne t Mask:255.255.255.0 Gateway: 19 2.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet
Product Mod el
About
Subnet Mask
Gateway
Restore IPC Default Configuration
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 201
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So the IP
address of the camera shall be changed to 192.168.1.X and the gateway
shall be changed to 192.168.1.1. After modification, please enter the
password of the administrator and click “Modify” button to modify the
settings.
The default password of the administrator is “123456”.
NCT-8ML-B21AF450043001279 A0
④ Bracket adjustment. Before adjustment, preview the image of the
camera on a monitor and then loosen the fixed ring to adjust the view
angle of the camera.
⑤
After that, adjust Zoom or Focus to obtain an optimum image. Before
adjustment, preview the image of the camera on a monitor.
**If the camera is fixed or motorized lens, please skip this step.
Open the cover of the camera and then insert a micro SD card.
⑥Install the cover back to the camera and fix it firmly with the
screws. (Note that the cover should not be installed unevenly.)
90° Tilt
360° Rotation 360° Pan
Focus
Zoom
②Route and connect the cables .
③Secure the mounting base with camera to the wall with the screws
provided.
∅4 .6 mm
1.89 in
1.89 in
③Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the above
table to show the network information on the right hand. Modify the IP
address and gateway of the camera and make sure the network address is
in the same local network segment as that of the computer. Please
modify the IP address of your device according to the practical
situation.
④Double-click the camera listed in the Xcel IP Utility or manually enter
the IP address in the address bar of the web browser to connect IP
Camera. Then follow directions to download and install the plugin.
⑤Enter the username and password in the login interface.
The default username is admin; the default password is 123456.
Fixed Ring
Inse rt a micro
SD card
Cover
Rubber plug