nvent Raychem RTD7AL User manual

RTD7AL
RTD temperature sensor for temperature measurement up to
900°F (482°C) in division 1 locations Installation Instructions
WARNING:
3 in (76 mm)
2 in (51 mm)
4.25 in
(108 mm)
3/4-in NPT
(19 mm)
conduit
opening
3 in (76 mm)
2 in (51 mm)
4.25 in
(108 mm)
3/4-in NPT
(19 mm)
conduit
opening
The nVent RAYCHEM RTD7AL temperature sensor is a three-wire platinum RTD
(resistance temperature detector) typically used with monitoring and control systems
when accurate temperature control is required. The sensor is explosion proof and
approved for Division 1 and 2 hazardous locations. The RTD7AL can be used with a wide
variety of RAYCHEM monitoring and control systems.
These installation instructions detail the installation of the RTD7AL in conjunction with
existing RAYCHEM component kits.
TOOLS REQUIRED
• 3.5 mm flat-blade screwdriver
ADDITIONAL MATERIALS REQUIRED
• Pipe straps
• Conduit with 16–22 AWG shielded instrument cable or equivalent armored cable
APPROVALS
The RTD7AL is CSA Certified for use in North America by the manufacturer for use in
Division 1 and Division 2 hazardous locations as follows:
Class I, Division 1, Groups A, B, C, D
Class II, Division 1, Groups E, F, G
Class I, Division 2, Groups A, B, C, D
Class II, Division 2, Groups E, F, G
KIT CONTENTS
Qty Description
1 RTD Temperature Sensor
SPECIFICATIONS
Sensor housing Aluminum; Type 4X
Sensor sheath 316 stainless steel
Range –100 to 900°F (–73 to 482°C) max
Accuracy ±1°F (0.5°C) at 32°F (0°C)
Resistance 100 ohms at 0°C α =0.00385 ohms/ohm/°C
Connection 3/4 in. NPT conduit hub
Operating Ambient –40°F to 212°F (–40°C to 100°C) for all gas groups except
Group A. –4°F to 212°F
(–20°C to 100°C) for gas Group A
DESCRIPTION
This component is an electrical device. It must be installed
correctly to ensure proper operation and to prevent shock or
fire. Read these important warnings and carefully follow all the
installation instructions. Component approvals and performance
are based on the use of specified parts only. Do not use
substitute parts or vinyl electrical tape to make connections.

WIRING INFORMATION
The length of RTD extension wires is determined by the wire
gauge used.
To reduce the likelihood that electrical noise will affect
temperature measurement, keep RTD extension wires as short
as possible.
Use shielded instrument cable such as
RAYCHEM MONI-RTD-WIRE (22AWG, PVC insulation, –30°F to
140°F, –20°C to 60°C) or Belden 83553 (22 AWG, FEP insulation,
–95°F to 395°F,–70°C to 200°C).
Maximum RTD extension wire length
AWG Feet (meters)
16 4500 (1400)
18 2800 (880)
20 1800 (550)
22 1100 (340)
C1D1 INSTALLATION WITH HEATING CABLE
Electrical Wiring Notes:
Most electrical codes (such as NEC 725–15) permit Class 1 circuits
to occupy the same cable, enclosure, or raceway without regard
to whether the individual circuits are alternating current or direct
current, providing all conductors are insulated for the maximum
voltage of any conductors in the cable, enclosure or raceway.
Additional Materials Required
• Approved junction box (supplied by others)
• HAK-C-100
• Pipe straps
Agency approved
Div 1 junction box
(supplied by others)
HAK-C-100
Div 2
Div 1
Pipe strap
Place pipe strap under heating cable
RTD DIRECT CONNECTION
Pipe strap
Place strap under heating cable
Conduit
drain
RTD7AL WIRING
Connect the wires as shown.
1 Note: Ground RTD extension wire shield at
one end only, preferably at RAYCHEM electronics end.
2 Note: RTD housing must be properly grounded
using the screw provided.
Electrical schematic of RTD
Red (Source)
White
Red
Red Red (Compensate)
Field Wiring
White (Common return)
North America
Tel. [phone]
Fax [phone]
[email protected]
Europe, Middle East, Africa
Tel. [phone]
Fax [phone]
[email protected]
Asia Pacific
Tel. [phone]
Fax [phone]
[email protected]
Latin America
Tel. [phone]
Fax [phone]
[email protected]
nVent.com
©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its aliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specications without notice.
Raychem-IM-H56916-RTD7AL-EN-1805 PN 229056-000